Netzsch 404 Pegasus

Zinc oxide (ZnO) has being recognised as a potentially interesting thermoelectric material, allowing flexible tuning of the electrical properties by donor doping. This work focuses on the assessment of tantalum doping effects on the relevant structural, microstructural, optical and thermoelectric properties of ZnO. Processing of the samples with a nominal composition Zn1−xTaxO by conventional solid-state route results in limited solubility of Ta in the wurtzite structure. Electronic doping is accompanied by the formation of other defects and dislocations as a compensation mechanism and simultaneous segregation of ZnTa2O6 at the grain boundaries. Highly defective structure and partial blocking of the grain boundaries suppress the electrical transport, while the evolution of Seebeck coefficient and band gap suggest that the charge carrier concentration continuously increases from x = 0 to 0.008. Thermal conductivity is almost not affected by the tantalum content. The highest ZT~0.07 at 1175 K observed for Zn0.998Ta0.002O is mainly provided by high Seebeck coefficient (−464 V/K) along with a moderate electrical conductivity of ~13 S/cm. The results suggest that tantalum may represent a suitable dopant for thermoelectric zinc oxide, but this requires the application of specific processing methods and compositional design to enhance the solubility of Ta in wurtzite lattice.

undefined Arias-Serrano, undefined Xie, undefined Aguirre, undefined Tobaldi, undefined Sarabando, undefined Rasekh, undefined Mikhalev, undefined Frade, undefined Weidenkaff, undefined Kovalevsky. Materials, 12 (13), 2057, 2019.

Low-density polyethylene (LDPE) composites reinforced with finely powdered waste glass were identified as a potential material for 3D printed structures for use in low-duty frictional applications. A recently published 3D printing model was used to calculate the limits in the filament feed rate and printing speed. Tribological tests (pin-on-disc method) of the printed composites were performed for different print-path directions. Differential scanning calorimetry (DSC) was performed on the samples and the composites showed a higher crystallinity compared with LDPE, which partially explains the higher elastic modulus of the composites determined during static tensile tests. Using a fine glass powder as reinforcement improved the wear resistance of LDPE by 50% due to the formation of a sliding film on the sample’s surface. An evident effect of friction direction vs. the printed path direction on wear was found; which was likely related to differences in the removal of friction products from the friction area for different print-path directions. The LDPE composites with fine waste glass particles are promising materials for low-duty frictional applications and should be the subject of further research.

Piotr Olesik, Marcin Godzierz, Mateusz Kozioł. Materials, 12 (16), 2520, 2019.

The energy released by the active metal phase in fine-grained Fe/Al energetic materials enables the replacement of conventional materials in new types of weapons. This paper describes an experiment designed to study the energy-release characteristics of fine-grained Fe/Al energetic jets under impact loading. By means of dynamic mechanical properties analysis, the physical and chemical properties of Fe/Al energetic materials with specific content are studied, and the preparation process is determined. The energy-release properties of fine-grained Fe/Al jets subject to different impact conditions are studied based on experimental data, and energy-release differences are discussed. The results show that for fine-grained Fe/Al energetic materials to remain active and exhibit high strength, the highest sintering temperature is 550 °C. With increasing impact energy, the energy release of fine-grained Fe/Al energetic jets increases. At an impact-energy threshold of 121.1 J/mm2, the chemical reaction of the fine-grained Fe/Al energetic jets is saturated. The experimental data and microscopic analysis show that when the impact energy reaches the threshold, the energy efficiency ratio of Fe/Al energetic jets can reach 95.3%.

undefined Li, undefined Du. Materials, 12 (20), 3317, 2019.

The rapid solidification of melt spinning has been widely used in the fabrication of high-performance skutterudite thermoelectric materials. However, the microstructure formation mechanism of the spun ribbon and its effects on the mechanical properties are still unclear. Here, we report the microstructure evolution and mechanical properties of La–Fe–Co–Sb skutterudite alloys fabricated by both long-term annealing and melt-spinning, followed by sintering approaches. It was found that the skutterudite phase nucleated directly from the under-cooled melt and grew into submicron dendrites during the melt-spinning process. Upon heating, the spun ribbons started to form nanoscale La-rich and La-poor skutterudite phases through spinodal decomposition at temperatures as low as 473 K. The coexistence of the micron-scale grain size, the submicron-scale dendrite segregation and the nanoscale spinodal decomposition leads to high thermoelectric performance and mechanical strength. The maximum three-point bending strength of the melt spinning sample was about 195 MPa, which was 70% higher than that of the annealed sample.

Huiyuan Geng, Jialun Zhang, Tianhong He, Lixia Zhang, Jicai Feng. Materials, 13 (4), 984, 2020.

Influence of Cu content on thermodynamic parameters (configurational entropy, Gibbs free energy of mixing, Gibbs free energy of amorphous phase formation), crystallization kinetics, structure and magnetic properties of Fe86-xCuxB14 (x = 0, 0.4, 0.55, 0.7, 1) alloys is investigated. The chemical composition has been optimized using a thermodynamic approach to obtain a minimum of Gibbs free energy of amorphous phase formation (minimum at 0.55 at.% of Cu). By using differential scanning calorimetry method the crystallization kinetics of amorphous melt-spun ribbons was analyzed. It was found that the average activation energy of α-Fe phase crystallization is in the range from 201.8 to 228.74 kJ/mol for studied samples. In order to obtain the lowest power core loss values, the isothermal annealing process was optimized in the temperature range from 260 °C to 400 °C. Materials annealed at optimal temperature had power core losses at 1 T/50 Hz—0.13–0.25 W/kg, magnetic saturation—1.47–1.6 T and coercivity—9.71–13.1 A/m. These samples were characterized by the amorphous structure with small amount of α-Fe nanocrystallites. The studies of complex permeability allowed to determine a minimum of both permeability values at 0.55 at.% of Cu. At the end of this work a correlation between thermodynamic parameters and kinetics, structure and magnetic properties were described.

Tymon Warski, Patryk Wlodarczyk, Marcin Polak, Przemyslaw Zackiewicz, Adrian Radon, Anna Wojcik, Maciej Szlezynger, Aleksandra Kolano-Burian, Lukasz Hawelek. Materials, 13 (6), 1451, 2020.

Laser beam-based deposition methods such as laser cladding or additive manufacturing of metals promises improved properties, performance, and reliability of the materials and therefore rely heavily on understanding the relationship between chemical composition, rapid solidification processing conditions, and resulting microstructural features. In this work, the phase formation of four Ni-Cr-Si alloys was studied as a function of cooling rate and chemical composition using a liquid droplet rapid solidification technique. Post mortem x-ray diffraction, scanning electron microscopy, and in situ synchrotron microbeam X-ray diffraction shows the present and evolution of the rapidly solidified microstructures. Furthermore, the obtained results were compared to standard laser deposition tests. In situ microbeam diffraction revealed that due to rapid cooling and an increasing amount of Cr and Si, metastable high-temperature silicides remain in the final microstructure. Due to more sluggish interface kinetics of intermetallic compounds than that of disorder solid solution, an anomalous eutectic structure becomes dominant over the regular lamellar microstructure at high cooling rates. The rapid solidification experiments produced a microstructure similar to the one generated in laser coating thus confirming that this rapid solidification test allows a rapid pre-screening of alloys suitable for laser beam-based processing techniques.

Xiaoshuang Li, Kai Zweiacker, Daniel Grolimund, Dario Ferreira Sanchez, Adriaan B. Spierings, Christian Leinenbach, Konrad Wegener. Materials, 13 (9), 2192, 2020.

This paper reports the results of the designing, manufacturing and characterization of a jewel obtained by means of coupling the dogmas of industrial design to the analytical engineering approach. The key role in the design of the jewel was played by an in-house synthesized Neodymium (Nd)-doped phosphate glass, selected due to its easy handling and capability to change color according to the incident light wavelength. The glass core was covered by a metal alloy to mitigate its relatively high fragility and sensitivity to thermal shock and, at the same time, to highlight and preserve its beauty. The selection of the proper metal alloy, having thermo-mechanical properties compatible with those exhibited by the glass, was carried out by means of Ashby’s maps, a powerful tool commonly adopted in the field of industrial design.

Diego Pugliese, Federico Simone Gobber, Ilaria Forno, Daniel Milanese, Marco Actis Grande. Materials, 13 (10), 2321, 2020.

In this article, the modification effects on Al–Mg2Si before and after heat treatment were investigated with Ca, Sb, and (Ca + Sb). In comparison with single Ca or Sb, the samples with composition modifiers (Ca + Sb) had the optimal microstructure. The sample with a molar ratio for Ca-to-Sb of 1:1 obtained relatively higher properties, for which the Brinell hardness values before and after heat treatment were remarkably increased by 31.74% and 28.93% in comparison with bare alloy. According to differential scanning calorimetry analysis (DSC), it was found that the nucleation behavior of the primary Mg2Si phase could be significantly improved by using chemical modifiers. Some white particles were found to be embedded in the center of Mg2Si phases, which were deduced to be Ca5Sb3 through X-ray diffraction (XRD) and field-emission scanning electron microscope (FESEM) analyses. Furthermore, Ca5Sb3 articles possess a rather low mismatch degree with Mg2Si particles based on Phase Transformation Crystallography Lab software (PTCLab) calculation, meaning that the efficient nucleation capability of Ca5Sb3 for Mg2Si particles could be estimated.

Min Zuo, Boda Ren, Zihan Xia, Wenwen Ma, Yidan Lv, Degang Zhao. Materials, 13 (12), 2714, 2020.

The as spun amorphous (Fe78Si9B13)99.5Zr0.5 (Zr0.5) and (Fe78Si9B13)99Zr1 (Zr1) ribbons having a Fenton-like reaction are proved to bear a good degradation performance in organic dye wastewater treatment for the first time by evaluating their degradation efficiency in methylene blue (MB) solution. Compared to the widely studied (Fe78Si9B13)100Zr0 (Zr0) amorphous ribbon for degradation, with increasing cZr (Zr atomic content), the as-spun Zr0, Zr0.5 and Zr1 amorphous ribbons have gradually increased degradation rate of MB solution. According to δc (characteristic distance) of as-spun Zr0, Zr0.5 and Zr1 ribbons, the free volume in Zr1 ribbon is higher Zr0 and Zr0.5 ribbons. In the reaction process, the Zr1 ribbon surface formed the 3D nano-porous structure with specific surface area higher than the cotton floc structure formed by Zr0 ribbon and coarse porous structure formed by Zr0.5 ribbon. The Zr1 ribbon’s high free volume and high specific surface area make its degradation rate of MB solution higher than that of Zr0 and Zr0.5 ribbons. This work not only provides a new method to remedying the organic dyes wastewater with high efficiency and low-cost, but also improves an application prospect of Fe-based glassy alloys.

Qi Chen, Zhicheng Yan, Hao Zhang, Lai-Chang Zhang, Haijian Ma, Wenlong Wang, Weimin Wang. Materials, 13 (17), 3694, 2020.

Magnetic and magnetocaloric properties of the amorphous Fe92−xZr8Bx ribbons were studied in this work. Fully amorphous Fe89Zr8B3, Fe88Zr8B4, and Fe87Zr8B5 ribbons were fabricated. The Curie temperature (Tc), saturation magnetization (Ms), and the maximum entropy change with the variation of a magnetic field (−ΔSmpeak) of the glassy ribbons were significantly improved by the boron addition. The mechanism for the enhanced Tc and −ΔSmpeak by boron addition was studied.

Xin Wang, Qiang Wang, Ben Zhen Tang, Ding Ding, Li Cui, Lei Xia. Materials, 13 (23), 5334, 2020.

Different fractions of hemp shives are used in the mixtures of the hemp–lime composite. The market offers shives of different granulation. It depends on the type of industrial hemp and on the capabilities of decortication machines. The aim of the research presented in the article is to check differences in the mechanical and hygro-thermal properties of composites with different shives fractions. The research part of the paper presents the preparation method and investigation on hemp–lime composites. Apparent density, total porosity, thermal conductivity, capillary uptake, vapor permeability, specific heat, mass absorptivity, flexural and compressive strength were examined. The results confirm that the shives fraction influences the individual properties of the composites. Hemp–lime composites with fine shives are characterized by higher water absorption, thermal conductivity, mechanical strength, vapor permeability as well as lower capillary-lifting capacity and specific heat than composites with thick shives.

Przemysław Brzyski, Mateusz Gładecki, Monika Rumińska, Karol Pietrak, Michał Kubiś, Piotr Łapka. Materials, 13 (23), 5383, 2020.

Al-based metallic glasses have a special atomic structure and should have a unique degradation ability in azo dye solutions. The Al88Ni9Y3 (Y3), Al85Ni9Y6 (Y6) and Al82Ni9Y9 (Y9) glassy ribbons are melt spun and used in degrading methyl orange (MO) azo dye solution with adding H2O2. With increasing cY, the as-spun ribbons have an increasing GFA (glass formability) and gradually decreased the degradation rate of MO solution. TEM (transmission electron microscopy) results show that the Y3 ribbon has nano-scale crystallites, which may form the channels to transport elements to the surface for degrading the MO solution. After adding H2O2, the degradation efficiency of Al-based glasses is improved and the Y6 ribbon has formed nano-scale crystallites embedded in the amorphous matrix and it has the largest improvement in MO solution degradation. These results indicate that forming nano-scale crystallites and adding H2O2 are effective methods to improve the degradation ability of Al-based glasses in azo dye solutions.

Qi Chen, Zhicheng Yan, Hao Zhang, KiBuem Kim, Weimin Wang. Materials, 14 (1), 39, 2020.

Degradation of the mechanical integrity of cobalt-based superalloys can occur as the carbide network is progressively oxidised during high temperature service. In this study, a heat-treatment aimed at redistributing the carbides was tested on two similar commercial Co-based superalloys, one with high C content (Co-101) and one with low C content (Stellite-21), to determine its influence on oxidation resistance. It was found that the carbide phases in the lower C-containing alloy could be solutioned more readily than the higher C-containing alloy, enabling the continuity of the carbide network to be reduced. This resulted in a reduced attack of the carbides down the interdendritic channels during oxidation testing, but increased thickness of the oxide overscale.

James P. Moffat, Tamsin E. Whitfield, Katerina A. Christofidou, Ed J. Pickering, Nicholas G. Jones, Howard J. Stone. Metals, 10 (2), 248, 2020.