Analytical instruments

1 2 3

Weighing range: 0 to 4100 g Readability (0 – 600 g): 0.01 g Readability (600 – 4100 g): 0.1 g Reprod (more)ucibility (0 – 600 g): 0.01 g Reproducibility (600 – 4100 g): 0.03 g Linearity (0 – 600 g): ± 0.05 g Linearity (600 – 4100 g): ± 0.02 g Weighing platform: 170 mm Dimensions (WxDxH): 194 x 316 x 68 mm Weight: 3.8 kg Including Mettler LabPac – M terminal

Partec Cyflow Space FACS stand alone system with Analytical cuvette. Equipped with: 4 measurable par (more)ameters: FCS, SSC, D3 and D4 bandpass filters (expandable to 9 parameters). Blue diode laser 20 mW 488 nm (expandable to 3 laser light sources). Sorting unit with green laser (sorting cuvette not included, but can be ordered from Sysmex). Fujitsu PC with Flowmax software for flow data analysis. Bottle rack for 1 liter bottles (for e.g. sheat fluids, buffers and waste).

Agilent 1100 system consisting of: 1x Agilent 1100 Degasser type G1379A 2x Agilent 1100 Isocratic Pu (more)mp type G1310A 1x Agilent 1100 Variable Wavelength Detector type G1314A 1x Agilent 1100 Fluorescence Detector type G1321A 2x Solvent tray Manual injector with 1 ml sample loop Laptop Agilent 1100 IsoPump: Hydraulic system: Dual piston in series pump with proprietary servo-controlled variable stroke drive, floating pistons and active inlet valve Setable flow range: 0.001 – 10 ml/min, in 0.001 ml/min increments Flow range: 0.2 – 10.0 ml/min Flow precision: < 0.3 % RSD (typically 0.15 %), based on retention time, at 1 ml/min Pressure: Operating range 0 – 40 MPa (0 – 400 bar, 0 – 5880 psi) up to 5 ml/min, Operating range 0 – 20 MPa (0 – 200 bar, 0 – 2950 psi) up to 10 ml/min Pressure pulsation: < 2 %amplitude (typically < 1 %), at 1 ml/min isopropanol, at all pressures > 10 bar (147 psi) Compressibility compensation: User-selectable, based on mobile phase compressibility Recommended pH range: 1.0 – 12.5, solvents with pH > 2.3 should not contain acids which attack stainless steel Dimensions (HxWxD): 140 x 345 x 435 mm Weight: 11 kg Agilent 1100 VWD: Detection type: Double-beam photometer Light source: Deuterium lamp Wavelength range: 190–600 nm Short term noise (ASTM): ± 0.75 x 10-5 AU at 254 nm Drift: 3 x 10-4 AU/hr at 254 nm Linearity: > 2 AU (5%) upper limit Wavelength accuracy: ± 1 nm Self-calibration with deuterium lines, verification with holmium oxide filter Band width: 6.5 nm typical Flow cell: 14-µl volume, 10-mm cell path length and 40 bar (588 psi) pressure maximum Dimensions (HxWxD): 140 x 345 x 435 mm Weight: 11 kg Agilent 1100 FLD: Detection type: Multi-signal fluorescence detector with rapid on-line scanning capabilities and spectral data analysis Light source: Xenon flash lamp Pulse frequency: 296 Hz for single signal mode, 74 Hz for spectral mode Excitation monochromator: range; 200 – 700 nm and zero-order,  bandwith; 20 nm, monochromator; concave holographic grating F/1.6 blaze 300 nm Emission monochromator: range; 280 – 900 nm and zero-order,  bandwith; 20 nm, monochromator; concave holographic grating F/1.6 blaze 400 nm Spectrum acquisition: Excitaiotn or emmision spectra, scan  speed; 28 ms per data point, step size; 1 – 20 nm Wavelength characterisric: Repeatability; ±0.2 nm, accuracy; ±3 nm Flow cell: 8 µl volume and 20 bar pressure, quartz Dimensions (HxWxD): 135 x 345 x 435 mm Weight: 11.5 kg

A Sartorius balance, type GE811 with a weighing range of 810 g and a readability of 0.1 g. dim. (wei (more)ghing platform): 145 x 175 mm.

Capacity: 410 g Readability: 1 mg Repeatability: 0.9 mg Linearity: ±2 mg Calibration type: Internal  (more)Dimensions (WxDxH): 194 x 366 x 276 mm Usable heigh of draft shield: 175 mm Weighing platform: 127 x 127 mm Weight: 7.6 kg

TSP HPLC P4000 + AS3000

Capacity: 3100 g Readability: 0.1 g Repeatability: 0.05 g Linearity: ± 0.1 g Taring range: 0 – 3100  (more)g Stabilization time: 1 – 2 s Dimensions (WxDxH): 204 x 385 x 90 mm Weighing platform dimensions (DxW): 204 x 204  mm Weight: 6.2 kg

Weighing range: 50g – 6500g Readability: 0,1g Dimensions (h x w x d): 110mm x 300mm x 250mm

Wavelength Range: 190 – 1100 nm Wavelength Accuracy: ± 0.5nm across wavelength range Wavelength Repr (more)oducibility: ± 0.1 nm Lamp Source: Xenon Beam: Double Beam Optical System: Czerny-Turner Monochromator Bandwidth: 2 nm Detector: Dual Solid State Silicon photodiode Photometric Range: -4.000 A to 4.000 A Stray Light: < 0.050%T at 220 nm (NaI), < 0.050%T at 340 nm (NaNO2) Zero Stability: ± 0.001A/hr at 500 nm Baseline Flatness: ± 0.002 A 220 to 900 nm Noise: <0.002 A peak to peak, 0.0008 A RMS near 2 A at 500 nm. <0.00020 A RMS at 0 A at 500 nm over 20 measurements Photometric Accuracy: ± 0.002 A at 0.5 A, ± 0.004 A at 1 A, ± 0.006 A at 2 A at 440 nm, 456 nm, 546.1 nm, 590 nm, 635 nm ± 0.005 A using 60 mg/L K2Cr2O7 Photometric Reproducibility: ± 0.002 A at 1 A Spectral Scanning: Yes (up to 1100 nm) Measurement Type: Fixed Wavelength, Abs/%T, Abs ratio, Abs difference, concentration (standard curve), concentration (factor), multiwavelength, kinetics, Life Science Methods, user log-on, Equation editor Cell Holder: Dual (sample and reference) Method Storage: Up to 90 on-board, unlimited via USB Display: Colour Touchscreen Data Interface: USB Dimensions (WxDxH): 535 x 440 x 335 mm Weight: 17.5 kg

See attached document for more information.

Maximum capacity: 810 g Minimum sample weight: 800 mg Readability: 10 mg Repeatability: 8 mg Lineari (more)ty deviation: 20 mg Setting time: 1.2 s Dimensions (WxDxH): 194 x 366 x 96 mm Weighing platform dimensions (WxD): 170 x 205 mm

System consists of: Agilent G1322A Degasser Agilent G1311A Quaternary Pump Agilent G1313A Autosample (more)r Agilent G1316A Thermostatted Column Compartment Agilent G1314A Variable Wavelength Detector

System consisting of: Gilson GX-281 sample robot 2 Gilson 6 position valves 2 Gilson 306 pump Gilson (more) 322 pump

System consisting of: Gilson GX-281 sample robot 2 Gilson 6 position valves Gilson 306 pump Gilson 1 (more)59 UV-Vis detector Gilson 321 pump Software

System contains: 2 Solvent cabinets 2 Capillary pumps 1 Well-plate samplers 2 Autosampler thermostat (more)s 1 Thermostatted colomn compartment 1 Diode array detector 1 Handheld control module Vacuum degasser cel is missing in the vacuum degasser Capillary pump: Settable column flow range: 0.01 – 20 µl/min Recommended column flow range: 1 – 20 µl/min Column flow precision: < 0.7 % RSD or 0.03 % SD (typically 0.4 % RSD or 0.02 % SD), at 10 µl/min and 50 µl/min column flow (based on RT, default setting) Optimum composition range: 1 to 99% or 5 µl/min per channel (primary flow), whatever is greater Composition precision: < 0.2 % SD, at 10 µl/min (20 µl flow sensor), 50 µl/min (100 µl flow sensor) and 1 ml/min (normal mode) default setting Delay volume: Typically 3 µl from the electronic flow control to the pump outlet for flow rates up to 20 µl/min. Pressure range: 20 to 400 bar (5880 psi) system pressure Compressibility compensation: User-selectable, based on mobile phase compressibility Recommended pH range: 1.0 – 8.5, solvents with pH < 2.3 should not contain acids which attack stainless steel. Upper pH range is limited by fused silica capillaries. Well-plate sampler: Safety features: Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display Injection range: 0.01 – 8 µl in 0.01 µl increments Precision: Typically < 0.5 % RSD of peak areas from 5 – 40 µl, Typically < 1 % RSD from 1 – 5 µl, Typically < 3 % RSD from 0.2 – 1 µl Sample viscosity range: 0.2 – 5 cp Sample capacity: 2 × well-plates (MTP) + 10 × 2 ml vials, 100 x 2 ml in one tray, 40 x 2 ml in half tray Injection cycle time: Typically < 30 s using following standard conditions: Default draw speed: 4 µl/min, Default eject speed: 10 µl/min, Injection volume: 0.1 µl Carry-over: Typically < 0.05 % using the following conditions: Column: 150 x 0.5 mm Hypersil ODS, 3 µm Mobile phase: Water/Acetonitrile = 85/15 Column Flow rate: 13 µl/min Injection volume: 1 µl caffeine (=25ng caffeine), 1 µl water to test carryover. Outside wash of needle before injection: 20 sec with water using flush port Autosampler thermostat: Temperature range: setable from 4 °C to 40 °C in 1 ° increments Temperature accuracy at ambient temperatures < 25 °C and humidity < 50%: – 1°C to + 4 °C at a setpoint of 4 °C Temperature accuracy at ambient temperatures > 25 °C and/or humidity > 50%: – 1°C to + 5 °C at a setpoint of 4 °C Thermostatted colomn compartment: Temperature range: 10 degrees below ambient to 80 °C, up to 80 °C: flow rates up to 5 ml/min Temperature stability: ± 0.15 °C Temperature accuracy: ± 0.8 °C (± 0.5 °C With calibration) Column capacity: Three 30 cm Warm-up/cool-down time: 5 minutes from ambient to 40 °C, 10 minutes from 40 – 20 °C Dead volume: 3 µl Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN via other series module Safety and maintenance: Extensive diagnostics, error detection and display (through control module and Agilent ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Diode array detector: Detection type: 1024-element photodiode array Light source: Deuterium and tungsten lamps Wavelength range: 190 – 950 nm Short term noise (ASTM) Single and Multi-Wavelengt: ± 1 × 10-5 AU at 254 and 750 nm Drift: 2 × 10-3 AU/hr at 254 nm Linear absorbance range: > 2 AU (upper limit) Wavelength accuracy: ± 1 nm Self-calibration with deuterium lines, verification with holmium oxide filter Wavelength bunching: 1 – 400 nm Programmable in steps of 1 nm Slit width: 1, 2, 4 , 8, 16 nm Programmable slit Diode width: < 1 nm Flow cells: 13 µl volume, 10 mm cell path length and 120 bar (1760 psi) pressure maximum Control and data evaluation: Agilent ChemStation for LC Analog outputs: Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, two outputs Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Safety and maintenance: Extensive diagnostics, error detection and display through control module and ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. GLP features: Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user-settable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with built-in holmium oxide filter. Handheld control module: The control module provides complete local control and monitoring of a single module or an entire Agilent series system. There is no data evaluation in the control module. The control module allows you to do a variety of HPLC tasks including automated sample preparation and injection, isocratic, gradient and multiple method analyses.

(dynamic) weighing, counting LCD with background light Capacity indication 230 VAC feed or rechargea (more)ble battery RS232 outlet with date and time Solid aluminum housing with stainless steel weighing platform Readibility: 0,2 gram Dimensions weighing platform: 240 x 200 mm

Solvent delivery method: Parallel-type double plunger Plunger capacity: 10µL Maximum discharge press (more)ure: 40MPa Flow-rate setting range: 0.0001 to 10.0000 mL/min Flow-rate accuracy: No more than 1% or 0.5µL/min, whichever is greater (0.01 to 2 mL/min.) Flow-rate precision: No more than 0.06% RSD or 0.02 min SD, whichever is greater Pulsation: 0.1 MPa (for water at 1.0 mL/min. and 7MPa) Constant-pressure solvent delivery: Supported Plunger rinsing mechanism: Manual rinsing or automatic rinsing using optional product Safety measures: Liquid-leakage sensor, high-pressure/low-pressure limits Gradient type: Low-pressure mixing Number of mixed solvents: 4 max Dimensions (WxHxD): 260 x 140 x 420 mm Weight: 10 kg

Ultra high performance means the highest resolution, highest sensitivity and fastest analysis – in o (more)ther words, a superlative LC system. Flexar FX-15 is the ultimate in UHPLC with maximum throughput and minimum stress for you. Getting more sample information in less time lets you be more productive.

Dual beam, Czerny-Turner monochromator, 190–1100 nm wavelength range, approximately 1.5 nm fixed spe (more)ctral bandwidth, full spectrum Xe pulse lamp single source with exceptionally long life, dual Si diode detectors, quartz overcoated optics, scan rates up to 24000 nm/min, 80 data points per s maximum measurement rate, non-measurement phase stepping wavelength drive, room light immunity, central control by PC with Microsoft Windows operating system.

Refractive index range: 1.00 – 1.75 Noise: 2.0 x 10-8 RIU (THF at 24°C with restrictor coil) Sensiti (more)vity: 1 (minimum) to 1024 (maximum) with scale factor Cell volume: 10µl Cell pressure (maximum): 7bar Flow rate: 0.3 – 10.0 ml/min (analytical), 0.3 – 20ml/min (with semi-prep option) Temperature control (internal heater): 30°C – 50°C Recorder output: 0 – 10 mV Intergrator output: Sensitivity setting 1 – 1V,  sensitivity setting 2 – 2V, sensitivity setting 4 – 4V, sensitivity setting 8 – 8V, sensitivity setting 16 to 1024 – 10V Measurement range: 5 x 10-3  RIU maximum FS (SENS = 1 and SF = 1), 5 x 10-8 RIU minimum FS (SENS = 1024 and SF = 100) Maximum drift: 2.5 x 10-7  RIU/hr (static with THF) Dimensions (H x W x D): 240 x 285 x 480 mm Weight: 18kg

Autosampler: Isocratic pump: