IKA RV05 Rotary Evaporator Motor

Yamato REV-202M Rotary Evaporator with Vacuum Regulator, Water Bath, and Selectable Glassware, 115V  (more)Speed Range 5 to 315 RPM Evaporation Capacity Up to 23 ml/min Pressure Setting Range 0 to 1013 hPa Features - Rotate faster & slower (315 RPM – 5 RPM) than any other rotary evaporator on the market to test new SOPs and develop better methods - Unit is easy to disassemble and clean after use - Program rotation direction changes, ramps, and other automations to get more done in the lab at once - Automatic on/off and suction speed adjustment via wireless vacuum controller - Easily analyze the residue left over after distillation - Orient for left or right-handed operation based on your limited bench space Standard rotary evaporator designed with vacuum controller and a slide jack mechanism for convenient height adjustment. Set includes the VR102S Vacuum Controller, BM302-A Water Bath, and your choice of glassware. Market leader in rotation speed range at 5 to 315 RPM. Designed with set inversion function where glassware and bath can be set on either side, left or right, depending on user’s dominant hand and installation location. Standard equipped with condenser insulation kit to suppress condensation on the condenser’s surface. INCLUDED: The Yamato REV-202M Rotary Evaporator with Vacuum Regulator, Water Bath, and Selectable Glassware, 115V includes: - Glassware Set Selected Above - VR102S Vacuum Regulator - BM302-A Water Bath - Rotary Joint - 1L Evaporation Flask - 1L Receiving Flask - Ball Joint Clamp - Flask Clip - Vacuum Seal - Condenser Insulation Kit - Condenser Bracket (Only for Glassware Sets B & C) - Hex Wrench - Power Cord - Operator's Manual - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

IKA RV 10 Digital Flex Rotary Evaporator Features - 4L Heating Bath with optimized heating bath volu (more)me allowing for fast-heat up - Left or right flask rotation with a speed range of 20 to 270 RPM - Features smooth start function along with a timer function - RS-232 digital interface for remote control and IR interface - Easy and safe operation due to ergonomical design of the user interface Motorized lift with Safety-Stop function, which lifts the receiving flask from the heating bath in case of a power failure Integrated push-off mechanism to loosen tightly fitting or stuck glassware for easy flask exchange Safety temperature circuits are featured, along with Dry-run protection for an adjustable lower end stop and lock function for the heating bath The RV 10 digital represents the continual enhancement of the IKA RV 10 Rotary Evaporator line. The unit comes with a new universal heating bath, vertical glassware, state-of-the-art safety features and digital connectivity. The RV 10 digital is a robust and reliable lab companion. Its optimized bath volume allows for fast heat-up times. The condenser unit has special designed glass tubes that utilize the 1500 cm² surface extremely efficient. That’s why the RV 10 basic delivers reliable and reproducible process results that are usually reserved for more costly systems. Additional features such as smooth start, left-right interval or timer function capability support the user in their daily lab work. Another important aspect of the RV 10 digital are the sophisticated safety features. The motorized lift has an automated lift-out function in case of power outage to prevent superheating of the solvent. Safety temperature circuits can be set individually. Dry-run protection, adjustable lower end stop and lock function of bath setting complete the line of safety features. Furthermore, IKA offers a choice of coated glassware for increased safety needs. The RS 232 interface allows for remote control via IKAs “labworldsoft”. The Heating bath is controlled via the IR interface from the main unit. INCLUDED The IKA RV 10 Digital Flex Rotary Evaporator includes: - RV 10 digital - HB digital S099 Heating Bath - RV 05.10 Balljoint clamp - RV 10.73 Vapor tube (NS 24/40) - RV 10.8001 Seal - RV 3.4 Woulff bottle - RV 3.1 Support pole - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer Warranty (+ Additional Free 3 Year Warranty Extension with IKA Registration) IKA RV 10 Digital Flex Rotary Evaporator SpecificationsType of coolingverticalCooling surface0 cm2Motor principleDCSpeed range5 - 280 rpmReversible direction of rotationyesLiftMotorStroke140 mmHeating temperature rangeroom temp. - 180 °CHeat output1350 WSet temperature resolution1 ±KFilling volume max.4 lTimer yes Dimensions (W x H x D)500 x 430 x 440 mm Weight18.5 kg Permissible ambient temperature5 - 40 °CPermissible relative humidity80 %Protection class according to DIN EN 60529IP 20RS 232 interfaceyesVoltage220 - 240 / 115 / 100 - 240 / 100 - 120 / 100 - 115 VFrequency50/60 HzPower input1400 WComparison of ModelsSpecificationIKA RV 10 Auto Pro FlexIKA RV 10 Digital FlexIKA RV 3 FlexIKA RV 8 FlexType of CoolingWithout CondenserVerticalN/AVerticalCooling Surface1500 cm²0 cm²N/A1500 cm²Speed Range5 - 300 rpm5 - 280 rpm20 - 300 rpm5 - 300 rpmLiftMotorMotorManualManualStroke140 mm140 mm150 mm120 mmHeating Temperature RangeRoom Temp. - 180 °CRoom Temp. - 180 °CRoom Temp. - 99 °CRoom Temp. - 180 °CTimerYesYesN/AN/ADimensions (W x H x D)500 x 430 x 440 mm500 x 430 x 440 mm440 x 530 x 330 mm510 x 490 x 345 mmWeight18.6 kg18.5 kg12 kg22.366 kgRS 232 InterfaceYesYesN/AN/AUSB InterfaceYesYesN/AN/AVoltage100 - 240 V220 - 240 / 115 / 100 - 240 / 100 - 120 / 100 - 115 V100 - 240 V100 - 240 V.comparison-table tr td:nth-child(3) { background-color: #fffacd; }

IKA RV 10 Auto V-C Rotary Evaporator Features - 4L heating bath optimized for rapid achievement of w (more)orking temperature, with a temperature safety circuit and boil-dry protection - Integrated vacuum controller and timer function - Bright, high-contrast, TFT, color-graphic control panel with simple menu navigation and programming for up to ten individual procedures - Automatic cooling water management, heating bath management, and ventilation - Right or left flask rotation with push-off mechanism for tightly-fitting flasks - Digital interfaces: USB port and RS-232 interface for remote control Motorized lift with Safety-Stop function, which lifts the receiving flask from the heating bath in case of a power failure Precise setting of distillation method per solvent with direct volume and efficiency control Integrated solvent library with 40 preset solvents and the ability to expand to incorporate new processes The completely revised RV 10 auto is the flagship of the IKA Rotation Evaporator product line. Its impressive features include an innovative control concept with a bright, high-contrast, TFT, color-graphic control panel, an integrated vacuum controller, cooling water monitoring and mature safety standards. The RV 10 auto offer all properties required for efficient, safe, and cost-effective operations. These include automatic control of the vacuum and cooling water volume. Its intuitive handling concept quickly leads its users to their desired results in every application. Thanks to specially designed glass guides, the condenser makes extremely efficient use of the 1500 cm² cooling surface. Thanks to its extended ramp programming capability, the RV 10 auto allows users to carry out customized procedures. Other innovative features, such as smooth start, interval mode, right-left operation in interval mode, or the timer function for time-lapse tests, make everyday work in the laboratory much easier. Safety is ensured by the motorized lift with safety-stop function that automatically lifts the evaporation flask out of the heating bath in the case of power failure. Additional safety for users is provided by individually adjustable temperature safety circuits, protection against boiling dry, adjustable end-point recognition to prevent glass breakage, and a locking function. The receiving flask and the condenser are also available in coated versions. The USB port or the RS-232 interface enable remote control with the IKA “labworldsoft” software package and an update option with the firmware update tool. The device comes complete with vacuum hoses and hose connectors for your in-house cooling water supply. INCLUDED The IKA RV 10 Auto V-C Rotary Evaporator includes: - RV10 control - RV 10 auto pro FLEX - HB digital S099 Heating Bath - VACSTAR digital Vacuum Pump - RV 10.910 Glassware vertical coated - RV 10.73 Vapor tube (NS 24/40) - RV 10.8001 Seal - Vacuum hose (2 x 0.55 m) - Water discharge hose (1 x 1 m) - Water discharge hose (1 x 1 m) - USB cable - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer Warranty (+ Additional Free 3 Year Warranty Extension with IKA Registration) IKA RV 10 Auto V-C Rotary Evaporator Specifications Type of coolingVertical condenser coatedCooling surface1500 cm2Speed range5 - 300 rpmReversible direction of rotationyesSpeed tolerance set rotation speed < 100rpm1 ±rpmSpeed tolerance set rotation speed 100rpm1 ±%LiftMotorStroke140 mmHeating temperature rangeroom temp. - 180 °CHeat output 1350 WSet temperature resolution1 ±KFilling volume max. 4 lVacuum controller integrated yesTimeryesDimensions (W x H x D)500 x 430 x 440 mmWeight31.56 kgPermissible ambient temperature5 - 40 °CPermissible relative humidity80 %Protection class according to DIN EN 60529IP 20RS 232 interfaceyesUSB interfaceyesAnalog outputyesVoltage100 - 240 VFrequency50/60 HzPower input100 WPower input standby3.3 WComparison of ModelsSpecificationRV 10 Auto Pro V-CRV 10 Auto V-CRV 10 Digital V-CRV 3 V-CRV 8 V-CType of CoolingVertical CondenserVertical Condenser CoatedVerticalVerticalVerticalSpeed Range5 - 300 rpm5 - 300 rpm5 - 280 rpm20 - 300 rpm5 - 300 rpmLiftMotorMotorMotorManualManualStroke140 mm140 mm140 mm150 mm120 mmHeating Temperature RangeRoom Temp. - 180 °CRoom Temp. - 180 °CRoom Temp. - 180 °CRoom Temp. - 99 °CRoom Temp. - 180 °CVacuum Controller IntegratedYesYesN/AN/AN/ATimerYesYesYesN/AN/ADimensions (W x H x D)500 x 430 x 440 mm500 x 430 x 440 mm500 x 430 x 440 mm440 x 530 x 330 mm510 x 490 x 345 mmWeight52.65 kg31.56 kg32.67 kg22.31 kg26.07 kgRS 232 InterfaceYesYesYesN/AN/AUSB InterfaceYesYesYesN/AN/AVoltage100 - 240 V100 - 240 V220 - 240 / 115 / 100 - 240 / 100 - 120 / 100 - 115 V100 - 240 V100 - 240 V.comparison-table tr td:nth-child(3) { background-color: #fffacd; }

Speed: 30 – 240 rpm Without glassware as-is

LABORATORY INCUBATORS CLN SMART POL-EKO CLN - NATURAL AIR CONVECTION CLN Series incubators maintain  (more)a constant temperature from 5°C above room temperature to a maximum of 100°C. Large touch display, programming, alarms, lock, stainless steel interior are just a small part of what you will find below! Continue reading, you will be surprised! ABSOLUTE CONTROL The SMART control panel is among the most complete you can find on the market. Large symbols and temperature values ​​guarantee comfortable and clear reading, combined with disarming ease of use. The latest generation touch screen responds to commands even if touched with latex gloves and is equipped with a large display: all values ​​are perfectly readable from any angle, regardless of the intensity of the light. DO YOU KNOW THE ADVANTAGES OF AN ADVANCED CONTROLLER LIKE THE SMART PANEL? - Sharp 4.3' color touch screen - Quick and easy data transfer: via LAN or USB - Fast, multi-segment, time and temperature programming - Visual and audible alarms with colored bar on display - Internal memory for programs and data storage - User manual downloadable directly from the controller - Loop function up to 255 times or infinite - Controls can be managed even when wearing latex gloves - Recording of the minimum, average and maximum temperature value for each segment - Overview of the set and current parameters during operation - Operation in temperature or time priority mode - ... and much more More and more? POL-EKO has already thought about it. For those who want cutting-edge functions and the freedom of transfer and remote use, POL-EKO offers you the SMART PRO controller. You can find all the differences between the SMART and SMART PRO panel in our dedicated post: insights on SMART and SMART PRO. With the SMART PRO versions, more accessories and options will also be available. QUALITY FIRST Resistant. Durable. POL-EKO incubators are designed and built to guarantee the best performance. They are a smart purchase, for customers who want to invest in the future of their laboratory. By choosing these products you will have precise results for years and years, repeatable and in complete comfort. The CLN SMART series incubators are built with the best materials and equipped with the most important accessories, to give you a complete and ready-to-use standard product. - Double door: solid external; glass interior - Powder coated sheet metal structure (graphite front panel) - Interior in acid-resistant stainless steel according to DIN 1.4301 - Insulated door with lock - Protection class 2.0 - Protection class 3.1 (DIN 12880) as option → - Stainless steel shelves - USB port for downloading recording data, events, manuals, service - LAN port - Open door alarm - Access port for external sensor - Rear air-flap - Quality control protocol (at +37°C) CLN SMART SERIES The six models of the CLN series cover most of your needs: from mini stoves to the 245 liter internal volume model. For larger volumes, look at the SLW series stoves. DETAILS AND ACCESSORIES Every detail of your POL-EKO models is designed to make routine work as simple and comfortable as possible. Below, the front and rear view. 1 - Rating plate 2 - Access port ø30mm for external sensor 3 - Internal glass door (for CL models) 4 - Adjustable feet 5 - Shelf 6 - External solid door 7 - Temperature sensors 8 - Open door sensor 9 - Touch control panel 10 - USB port 11 - Handle with key lock 1 - Main switch 2 - Connector for connecting a hose with nitrogen (only for SLWN models) 3 - Air-flap 4 - LAN port 5 - Fuse 6 - Main power socket C20 OPTIONS POL-EKO allows you to increase the possibilities of your incubator with quality accessories; to better adapt to particular applications or to equip the instrument with safety systems and advanced connections. - Stainless steel shelf - Perforated shelf - Stainless steel basins - Door with viewing window - LabDesk software - IQ OQ PQ calibration and qualification - Overtemperature protection class 3.1 according to DIN 12880 - Backup battery for the display in case of power failure - Clean contact - LAN cable - Non-standard 20 / 60 / 100 mm access door - Additional 30 mm access door - Castors - Table with castors

Cooling recirculator model ULK 1002 FRYKA The universal chiller for laboratory and industry, charact (more)erized by its flexibility in various applications. A great economical alternative to running water cooling systems. The 9.5-liter tank allows for wide-ranging methods of use: when full, it ensures high temperature stability over time and, at a minimum, a rapid cooling system for the most immediate needs. The new modern space-saving design, low weight, innovative technical features with low-noise cooling unit, also make it suitable for direct use at the workplace. Energy efficient: - fan with EC technology Low noise level: - particularly quiet components - the fan adjusts its speed to the required value Easy to use: - integrated funnel - self-sealing hose connector with quick coupling - drain cock High quality components: - touchscreen controller with high quality glass screen and integrated digital flow and fill level indicators - components from renowned German manufacturers - refrigeration unit: completely hermetically sealed, air cooled, low maintenance High operational reliability: - thermal overload protection - dry-running protection - optical and acoustic alarm - error messages are displayed in plain text Proven standard: - MOD bus interface Technical features: Operation from -10°C to +40°C Control accuracy +/- 0.5K Cooling capacity in watts at + 20°C 1200W; at + 10°C 850W; at -10°C 400W Circulation pump: flow rate 12 l / min Flow pressure: 2.9 bar External dimensions [LxWxH]: 35 x 44.5 x 66 cm Weight: 41 kg Ambient temperature from +12°C to +30°C Electrical connection: 230 V / 50 Hz Max current: 3.5 A Coolant tank from 2.5 to 9.5 l Fitting for 12 mm hose

Ohaus HB4DG Digital Dry Block Heater, 4 Block Temperature Range Ambient +5°C to 120°C Control Digita (more)l Uniformity Within the Block ± 0.1°C at 37°C Features - Offers accurate and fast sample heating with PID microprocessor temperature control - Supports four interchangeable modular blocks with over 40 configurations - Tool-free block setup for easy operation - Enhanced tube-to-block contact for maximum heat retention and efficiency - Robust painted steel housing for durability - Equipped with a clear LED display and easy-to-use touchpad controls with independent displays for temperature and time - Timer from 1 second to 9,999 minutes - Includes a unique single point calibration feature to match the block heater's display to a known external temperature standard for 3 temperature setpoints - Versatile utility across various laboratory applications - Designed for long-lasting performance in demanding settings The Ohaus HB4DG Digital Dry Block Heater offers accurate and fast sample heating with PID microprocessor temperature control, making it perfect for various applications that demand consistent heating. This heater accommodates four interchangeable modular blocks, providing over 40 configuration choices to suit different needs. The modular blocks are designed for effortless setup without requiring tools, ensuring optimal tube-to-block contact for superior heat retention and efficient operation. The HB4DG features a robust painted steel housing and is equipped with a clear LED display, easy-to-use touchpad controls with independent displays for temperature and time, and an audible alarm, enhancing usability and precision. This Dry Block Heater also includes a unique single point calibration feature to match the block heater's display to a known external temperature standard for 3 temperature setpoints, making it a superior choice for modern lab environments.Please Note: Blocks are sold separately and are REQUIRED for operation. Please view the Accessories tab. INCLUDED: The Ohaus HB4DG Digital Dry Block Heater, 4 Block includes: - Support Rod Holder with Locking Knob - Power Cord - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Hermle 3 x 100ml insert for Z496-1000-RBUK 2/pk The Hermle 3 x 100ml insert is a specially designed  (more)accessory for use with the Hermle Z496-1000-RBUK rectangular buckets. This insert comes in a pack of 2 and is capable of accommodating tubes with a maximum diameter of 40mm and length of 123mm. With a maximum capacity of 3 x 100ml per adapter, this insert allows for efficient processing of medium size sample volumes. The compatibility with Hermle Z496-1000-RBUK rectangular buckets makes this insert a versatile addition to any laboratory looking to improve their sample processing workflow. The use of this insert ensures that tubes are securely held in place during centrifugation, preventing any sample loss or contamination. INCLUDED: The Hermle 3 x 100ml insert for Z496-1000-RBUK 2/pk includes: - Set of 2 Adapters - Manufacturer's Documentation - 2 Year Manufacturer's Warranty