Rötzmeier Sicherheitsbehälter (Edelstahl) TK 51

The G 7883 washer-disinfector is suitable for reusing laboratory glassware for analytical experiment (more)s in, for example, industrial, environmental and research laboratories. This appliance has a large two-tier wash area and can be built-in under a continuous worktop or used free-standing. After an intensive main cleaning phase, disinfection takes place at >90°C and a storage time of 5 minutes. The final rinse is performed with deionized water without rinsing agents. Control/programs: Multitronic Novo Plus control (certain process parameters can be changed), with 10 standard cleaning programs Program operation/display: Operation via one-button program selector, display of program cycles, display of temperature and program duration, display of program end, optical and acoustic signal, indicator lights for service and fault messages Cleaning mechanisms: Rotating: two spray arms on top and bottom of the chamber, third spray arm on top basket. Dosing devices: Valve dispensers for powdered detergent and liquid detergents. Circulation pump: 400 l/min Temperature: Freely adjustable up to 93°C Drain: 1 drain hose Drying capacity: Gravity convection drying system, 10 minutes. Can be turned on or off in any cycle Water connection: 1x hot water, 1x cold water, 1x purified water Dimensions (WxDxH): 600 x 600 x 850 mm Weight: 74 kg

MORE DETAILS TO FOLLOW

Steelco LAB 500 SCDL Laboratory Washer This was removed from a university lab where it was surplus t (more)o requirements. The unit powers up and is in good working order. It is in good cosmetic condition with minor marks from use.

Miele Dishwasher G7883 / Aqua Purifier G 7895 / Dosing unit DOS G60 Lab These items were removed fro (more)m a university lab, where they were surplus to requirement. All units are in good cosmetic condition and working order. Included are the following: - Miele Dishwasher Model: G 7883      L69cm x W60cm x H85cm - Aqua Purifier Model: G 7895      L60cm x W30cm x H87cm - Dosing Unit Model: DOS G60

Lancer 820 LX Undercounter Laboratory Washer and Dryer This was removed from a university lab where  (more)it was surplus to requirements. The unit powers up and is in full working order. It is in good cosmetic condition with minor marks. Internal dimensions - D51 W52 H52cm

Muffle furnace Selecta SELECT HORN. Chamber capacity 9 L. Adjustable temperature up to 1150 °C. Accu (more)racy ±1 °C. Resolution: 1 digit. Digital electronic temperature and time controller that allows programming a ramp of up to 8 segments or two of 4 segments. Heating elements evenly distributed. Fiber-ceramic insulation. Up-and-over door with disconnection of operation in opening. It has some flaws in the paint that do not prevent its operation. Dimensions: inside 15*20*30 cm, outside 58*59*65 cm; 70KG. 3000 W. User manual. The Selecta SELECT HORN muffle furnace is high-quality equipment designed to carry out calcination, heat treatment and other processes at high temperatures in a precise and controlled manner. With a heavy-duty heating chamber and a digital control system, this oven guarantees uniform heat distribution and a constant temperature throughout its interior. With a capacity of up to 1150°C, the Selecta SELECT HORN muffle furnace is ideal for research laboratories, chemical and metallurgical industries, as well as applications in the field of ceramics and jewelry. Its compact design and robust construction make it easy to use and maintain, ensuring reliable, long-lasting performance in every work cycle. In addition, the Selecta SELECT HORN muffle furnace has a safety system that protects both the equipment and the user, avoiding possible accidents during its operation. With an intuitive interface and programmable functions, this oven offers versatility and precision in each process, making it an indispensable tool for any laboratory or industry that requires high controlled temperatures.

Agilent 1100 system consisting of: 1x Agilent 1100 Degasser type G1379A 2x Agilent 1100 Isocratic Pu (more)mp type G1310A 1x Agilent 1100 Variable Wavelength Detector type G1314A 1x Agilent 1100 Fluorescence Detector type G1321A 2x Solvent tray Manual injector with 1 ml sample loop Laptop Agilent 1100 IsoPump: Hydraulic system: Dual piston in series pump with proprietary servo-controlled variable stroke drive, floating pistons and active inlet valve Setable flow range: 0.001 – 10 ml/min, in 0.001 ml/min increments Flow range: 0.2 – 10.0 ml/min Flow precision: < 0.3 % RSD (typically 0.15 %), based on retention time, at 1 ml/min Pressure: Operating range 0 – 40 MPa (0 – 400 bar, 0 – 5880 psi) up to 5 ml/min, Operating range 0 – 20 MPa (0 – 200 bar, 0 – 2950 psi) up to 10 ml/min Pressure pulsation: < 2 %amplitude (typically < 1 %), at 1 ml/min isopropanol, at all pressures > 10 bar (147 psi) Compressibility compensation: User-selectable, based on mobile phase compressibility Recommended pH range: 1.0 – 12.5, solvents with pH > 2.3 should not contain acids which attack stainless steel Dimensions (HxWxD): 140 x 345 x 435 mm Weight: 11 kg Agilent 1100 VWD: Detection type: Double-beam photometer Light source: Deuterium lamp Wavelength range: 190–600 nm Short term noise (ASTM): ± 0.75 x 10-5 AU at 254 nm Drift: 3 x 10-4 AU/hr at 254 nm Linearity: > 2 AU (5%) upper limit Wavelength accuracy: ± 1 nm Self-calibration with deuterium lines, verification with holmium oxide filter Band width: 6.5 nm typical Flow cell: 14-µl volume, 10-mm cell path length and 40 bar (588 psi) pressure maximum Dimensions (HxWxD): 140 x 345 x 435 mm Weight: 11 kg Agilent 1100 FLD: Detection type: Multi-signal fluorescence detector with rapid on-line scanning capabilities and spectral data analysis Light source: Xenon flash lamp Pulse frequency: 296 Hz for single signal mode, 74 Hz for spectral mode Excitation monochromator: range; 200 – 700 nm and zero-order,  bandwith; 20 nm, monochromator; concave holographic grating F/1.6 blaze 300 nm Emission monochromator: range; 280 – 900 nm and zero-order,  bandwith; 20 nm, monochromator; concave holographic grating F/1.6 blaze 400 nm Spectrum acquisition: Excitaiotn or emmision spectra, scan  speed; 28 ms per data point, step size; 1 – 20 nm Wavelength characterisric: Repeatability; ±0.2 nm, accuracy; ±3 nm Flow cell: 8 µl volume and 20 bar pressure, quartz Dimensions (HxWxD): 135 x 345 x 435 mm Weight: 11.5 kg

Lauda CS 6-D recirculating bath with heating. Ambient temperature range +5ºC to +199.9ºC. Great temp (more)erature stability. Internal dimensions (HWD) 15 x 13 x 15 cm. External dimensions (HWD): 23 x 40 x 40 cm. It has some scratches and other cosmetic damage that does not affect its operation. The Lauda recirculating bath type CS6 is suitable for applications that require a precise temperature. It is equipped with a built-in circulation pump making it ideal for uniform heating of reaction mixtures.

Stainless steel platform scale with four sensors No matter where you place the load on the platform, (more) the result will always be correct. This is due to the four sensors built into the platform. You will appreciate this especially when weighing an irregularly shaped object. It has been with us for years, and will stay for a long time to come The LCD display has accompanied us for long years. During this time it has proven its reliability. It guarantees the readability of the result from many angles and is energy efficient. Inner power No access to mains power? Power failure? No problem. Thanks to its internal rechargeable battery, the H315 scale works anyway (up to 7 hours). Power supply is available at an extra charge. As standard, the scale is equipped with a RS232 cable, to which you can connect most of the accessories from our range. Not just weighing But also parts counting, percent weighing, animal weighing and peak hold. The power of H315&rsquo;s working mods. Do you require fast and repeatable weight measurement under difficult conditions? The H315 scale is made for that! Work as you like The PUE H315 terminal sits on a 3-meter cable that allows you to hang the terminal on the wall. This allows you to arrange your weighing workplace in many ways. The power of steel The use of stainless steel guarantees you a long life for the scale. It is not afraid of contact with moist objects or accidental splashes. The membrane keyboard is another argument in the discussion of the water resistance of this scale. If you need a dual-range scale, we can make one for you at an extra cost.

M1 Mass Standard - knob weights. Nominal value - 200 kg.

Heidolph Hei-FLOW Core 600 Peristaltic Pump This pump of the Hei-Flow Core series is particularly su (more)itable when high volumes need to be transported easily. A flow rate of 4.0 - 4,151 ml / min can be set for this purpose. This model is designed for the use of single-channel pump heads.Even with a load change, the speed of 50 — 600 rpm is kept constant at a control accuracy of ±5%. It is easy to switch to the reverse direction of rotation. Click Here to View Product Video INCLUDED: The Heidolph Hei-FLOW Core 600 Peristaltic Pump includes: - Power Cord - Operator's Guide - Full 3 Year Manufacturer's Warranty