N-Biotek NB-101S RC Orbital Shaker

IKA MS2 Minishaker / laboratory vortex Laboratory use Voltage: 230V, 50-60Hz Power: 31W Stirring fre (more)quency: 0 – 2500 1/min Mini shaker dimensions (L) x (D) x (H): 11.5 x 23 x 8cm Orbital displacement of 4.5 mm Plate dimensions (ø): 7 cm 2 modes: continuous rotation or pulse

Microplate shaker with microprocessor control that can accommodate two or four microplates, deep wel (more)l plates or two microtube racks. Variable speed over a wide range can be adjusted to suit the application; a low speed ensures that the contents of the well are not ejected, more vigorous stirring provides effective aeration over the small surface area of each of the wells. Ideal for use in immunology, biotechnology, microbiology and pharmacology applications. Two independent LED displays show speed and time Integrated timer, 1 s to 160 hours, shows elapsed time or counts down, automatic switch-off and acoustic alarm when program is completed Can be used at −10 to +60 °C (80% relative humidity, non-condensing), in an incubator, CO₂ incubator or cold room Speed: 100 – 1200 rpm Speed accuracy: ±2% Circular movement: 3.0mm Number of places for microplates: 4 Dimensions (WxDxH): 280 x 430 x 100 mm Weight: 10 kg

This Thermo Scientific MaxQ 6000 Incubator Shaker Model - 4360 was removed from a university la (more)b where it was surplus to requirements. The unit has a power board fault. It is in reasonably good cosmetic condition with some marks from use. The door also does not close properly. Internal dimensions - D52 x W55 x H67cm1 Shelf - 52 x 54cmShaker Plate - 45 x 45cm It is sold for spares or repairs due to the electrical fault.

Ohaus SHHD2325DG Heavy Duty ShakerThe OhausSHHD2325DG Digital 23 kg Capacity Heavy Duty Orbital Shak (more)er is designed forapplications with heavy duty loads. Shaker provides reproducible motion that isevenly distributed throughout the entire surface of the tray.With a loadcapacity up to 50 lbs and over 70 accessory options and with microprocessorcontrol to provide variable speed and consistent shaking, while ramping to theset speed. Microprocessor displays the last set-point and will restart if poweris interrupted. Built-in tray and non-slip rubber mat included with theSHHD2325AL.Touchpadcontrols with independent LEDs for speed/time allow operator to view allsettings at once. Timer displays elapsed time or when programmed to a set time,will turn off when time reaches zero.Speed rampingfeature slowly increases the speed to desired setpoint to avoid splashing. Theload sensor detects unbalanced conditions and automatically reduces rpm to asafe speed to protect samples.Click Here to View Product Video INCLUDED: The Ohaus SHHD2325DG Heavy Duty Shaker includes: - Non-Skid Rubber Mat - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

IKA HS 260 Control Shaker Type of Movement Reciprocating Speed Range 10 to 300 RPM Shaking Stroke 20 (more) mm Features - Electronic adjustment of speed and timer - Digital display makes it possible to read the speed, timer function and operating modes - Electronic time switching clock: 0 - 9 h 59min or continuous operation (endless) - With integrated endpoint positioning (for automated robot-controlled sampling) - All functions can be controlled and documented with labworldsoft® software - Wide range of attachment combinations makes it possible to use almost all shapes and sizes of vessels - Attachments are not included, please order separately The HS 260 control open air reciprocating shaker is a reliable and efficient solution for laboratory applications that require gentle mixing of samples. It has a compact and flat design, making it easy to fit into any lab space. With a maximum shaking weight of 7.5 kg, it can handle a variety of vessel sizes and shapes. The shaker's integrated end point positioning function is highly useful for automated robot-controlled sampling.

Water bath from 25°C to 99.9°C for the laboratory The shaking water baths of the LAUDA Hydro series  (more)stir laboratory samples with linear or orbital motion, depending on the model. They are reliable instruments, ideal for any laboratory application, be it biological, medical or biochemical, guaranteeing a homogeneous distribution of the temperature. The integrated speed controller enables a load-independent, continuously adjustable stirring movement with soft start. The H 20 SW and H 20 SOW shaking water baths are equipped with a cooling coil as standard. The temperature range can be extended to a minimum of +10°C by connecting them to the domestic water supply or commercially available circulating chillers. Qualitative characteristics - Digital regulation of the temperature and indication via LED display - Load-independent, continuously variable stirring with soft start - Electronic monitoring of the thermoregulator functions, with two fuses for under/over temperature protection - Tank, frame, cover with condensation channel, shaking basket and heater in stainless steel - No dripping condensation – arched insulating lid to reduce heat loss and prevent condensation from dripping onto samples Operation All water baths come standard with a perforated pan and no racks are required. Flasks and containers can be placed directly on the bottom. The drain valve is located on the rear side. Controllers The control panel consists of a large, high-contrast TFT display and a membrane keyboard with four softkeys, protected against dirt and water drops. The menu will guide you on how to use the bain-marie correctly. Esempi applicativi - Bacteriological tests - Molecular biology - Demulsivity studies - Processing of chemical reactions - Thawing - Metallurgical analyses - Incubation of microbiological assays - heating reagents - Environmental studies - Food Processing (QC) - Water quality research - Cytochemistry Accessories available Water level regulator. The heating element is located directly under the sieve plate for even temperature distribution in the tank. Electronic monitoring of the temperature regulator. Two independently operating temperature fuses. Improved visual and audible alarms for increased sample safety. Control elements tilted back for increased splash protection and improved operating comfort. - Perforated plate to place the glassware directly on the bottom. - Fill mark max. to prevent overflows. - Easy removal of sieve plate for cleaning. Highest quality materials: tank interior, lid, sieve and heating element made of stainless steel. Heat insulating lid in stainless steel, double walled with internal curvature to guide the condensate. Limescale deposits inside the water bath can be removed with normal commercial descalers. The internal tray can be easily disassembled and lifted for quick and thorough cleaning. Recommended accessories - Water level regulator. Thanks to this accessory, the loss of water inside the instrument (through evaporation) is compensated and the water level is kept constant. Furthermore, it allows use at temperatures below ambient temperatures, with a minimum of approx. 3°C above tap water temperature.

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Particle size measurement instruments typically employ deionized or even untreated water as a suspen (more)sion medium for particle dispersion during analysis. Usually, this water contains undesirable levels of dissolved gases, most often those commonly present in the atmosphere. During analysis, these gases can come out of solution, forming minute bubbles that can have important effects on the analytical results. Regardless of the relative size of the bubbles, their presence distorts the reported distribution of sizes; it also degrades the repeatability of analyses. The more powerful the analyzer, the more pronounced these effects can be. When using a highly sensitive instrument such as the Micromeritics Saturn DigiSizer, removal of the dissolved gases (that subsequently lead to bubble formation) is therefore extremely desirable for obtaining the most accurate particle size data possible. The Micromeritics AquaPrep is a highly-effective system for freeing water of dissolved gases for use with the Saturn DigiSizer. The AquaPrep recirculates water through a hydrophobic capsule consisting of many thin-walled capillaries. A vacuum pump provides low pressure on the outside of the capillaries, causing a diffusion of dissolved air from the water through the capillary walls and into the vacuum pump. The air removed from the water is subsequently exhausted through a small tube at the front of the instrument, which is connected to a bubbler-type apparatus for performance monitoring. During typical operation, the AquaPrep can prepare approximately 5 liters of water for analysis in less than 2 hours. Because air bubbles scatter light as do particles, the AquaPrep enhances even further the high-accuracy analysis of small particles. Its compact, rugged, and reliable design make it ideal for use in a wide variety of aqueous particlesizing applications.

Convenient Transportation of Small Mass Standards The mass standards tweezers are tongs/ pliers that (more) will enable you to conveniently and precisely grasp and transport small mass standards. With it, you can easily and quickly place or lay an object (for example, a mass standard) on the pan and remove it from the pan. The tweezers protect the mass standards from finger grease, moisture and other factors that interfere with the measurement. It is indispensable in the daily use of laboratory balances. Tweezers 250 mm Material: stainless steel with a silicone tip for standards up to 500 g What Kind of Tweezers for Mass Standards? TWEEZERS LENGHT APPLICATION Standard 105 mm up to 50 g 160 mm up to 200 g 250 mm up to 500 g 300 mm up to 500 g Made of carbon fiber 105 mm up to 50 g With a carbon fiber tip 105 mm up to 50 g 155 mm up to 200 g 185 mm up to 200 g 200 mm up to 200 g

Memmert UN55 Natural Convection Oven 53L, 115V Temperature Range Ambient +5°C to 300°C Convection T (more)ype Natural Convection Chamber Volume 53L Features - 53-liter chamber volume accommodates various sample sizes, enhancing lab versatility - Precise temperature control from +5°C above ambient to 300°C for sensitive applications - Ergonomic PID controller with high-definition TFT display for intuitive adjustments - Durable stainless steel interior and exterior, corrosion-resistant for rigorous use - Natural convection ensures uniform heat distribution for delicate samples - Pre-heated fresh air admixture with adjustable air flap for temperature uniformity - Adaptive settings include programmable temperature, timer, and setpoint wait for workflow optimization - AtmoCONTROL software for data logging and remote monitoring via Ethernet - Easy-to-clean stainless steel interior with reinforced ribbing, ideal for frequent use The Memmert UN55 Natural Convection Oven 53L, 115V delivers precise temperature control from +5°C above ambient to 300°C, making it ideal for a variety of sensitive applications. Featuring an ergonomic digital PID controller with a high-definition TFT display, this oven offers intuitive settings and rapid access to temperature adjustments. Built for rigorous lab environments, its durable stainless steel construction resists corrosion, while the natural convection system ensures even, consistent heating distribution across all samples. Fully adjustable safety controls, including a built-in overtemperature monitor, provide added protection and peace of mind. With an easy-to-clean interior and robust stainless steel shelving, the UN55 maximizes efficiency in daily operations, delivering reliable performance for years to come. INCLUDED: The Memmert UN55 Natural Convection Oven 53L, 115V includes: - 1 Stainless Steel Grid - Tilt Protection Wall Bracket - Calibration Certificate - Power Cord - Operator's Manual - Manufacturer's Documentation - 3 Year Manufacturer's Warranty

Edwards XDS35iE Enhanced Dry Scroll Pump Ultimate Vacuum 0.03 mbar (0.02 Torr) Peak Pumping Speed 3 (more)5 CFM (21 m3/h-1) Inlet Connection DN 40 ISO-KF (NW40) Features - Proven dry, clean vacuum solutions for a broad range of applications - Features smart drive technology for optimal global performance - Enhanced with double start scroll form technology and by-pass valves - Reduced peak power requirements at roughing pressures for efficient operation - Continuous higher roughing speeds to handle special application needs - High flow gas ballast feature allows pumping of vapours, including water vapour up to 240 gh-1 - Simple single-sided scroll design facilitates quick and easy maintenance - Offers up to 25% increased pumping speed at roughing pressures for frequent cycling - Equipped with DN 40 ISO-KF (NW40) inlet and DN 25 ISO-KF (NW25) outlet for effective connectivity The Edwards XDS35iE Enhanced Dry Scroll Pump represents a cutting-edge solution in dry, clean vacuum technology, suitable for a wide array of applications. This pump is equipped with double start scroll form technology and by-pass valves, enhancing the original XDS35i family by increasing the roughing performance and capacity for large volume evacuations. The pump's smart motor drive ensures consistent global performance, includes overload protection, and facilitates remote start/stop operations. A key feature is the high flow gas ballast, allowing the handling of water vapour and other vapours up to 240 gh-1. Maintenance is streamlined thanks to its simple single-sided scroll design, ensuring low ownership costs and maximum uptime. Additionally, the pump features reduced peak power requirements by up to 20% during initial pump down and provides up to 25% more pumping speed at roughing pressures, ideal for high frequency cycling applications. The pump achieves an ultimate vacuum of 0.03 mbar (0.02 Torr), which slightly increases with gas ballast usage, and offers a peak pumping speed of 35 CFM. It is designed with a DN 40 ISO-KF (NW40) inlet and a DN 25 ISO-KF (NW25) outlet, ensuring efficient connectivity and robust performance. Click Here to View Product Video INCLUDED: The Edwards XDS35iE Enhanced Dry Scroll Pump includes: - Power Cord - Operator's Manual - Manufacturer's Documentation - 1 Year Manufacturer's Warranty