Rigaku - XRD Parts MicroMax-007HF Rotating Anode X-Ray Generator, AFC-11R NOTE - THIS IS A SPARES/REPAIRS ITEM

Oxford Diffraction Xcalibur PX Ultra Crystal Diffraction X-ray Generator System This system was remo (more)ved from a university lab where it was surplus to requirements. The system is in very good cosmetic condition, but several units encountered issues during testing, and no PC or control software is included. As such, the system is listed for spares/repair. - Further information regarding issues faced are stated below. The lab stated it had been not used for some time but had some issues. The system units include: - Oxford Diffraction Xcalibur PX Ultra - Serial No.: XXH-127/05 - Year: 2005 - Powered on with mains light, Shutter Closed status light, inner display screen, and hand-held remote keypad all functioning - Oxford Diffraction X-ray Protection Cabinet - Serial No.: XPD-127/05 - Year: 2005 - Thermo Scientific Neslab ThermoFlex 10,000 Recirculating Chiller - Serial No.: 1111473501170217 - Powered on but shut off after 1 second with error code "PHEr" (limit fault) - Oxford Diffraction KMW200CCD CCD Detector Chiller Unit - Serial No.: CCA 73/06 - Year: 2006 - Powered on, but no further testing possible - Oxford Diffraction KMC3000C X-ray Tube Chiller - Serial No.: CAC-142/05 - Year: 2005 - Powered on, pump ran, thermostat seemed functional, but not fully tested - Oxford Diffraction Cryodrive 2.0 - Serial No.: R72-0558 - 6944 running hours - Powered on, but no further testing without gas supply - Oxford Cryosystems Cobra Controller 700 Series Cold Head Controller - Serial No.: 741174 - Powered on, displayed ambient temperature, status lights, and responsive buttons - Parker NitroFlowLab Nitrogen Generator - Model No.: 4278 - Serial No.: 4278-13NFLC0008 - Powered on, displayed a message "writing information to an SD card," and did not allow further actions - Oxford Cryosystems Standard Cobra Nitrogen Control Pump - Serial No.: CB171 - Agilent HS 602 Vacuum Pump with NW25 Oil Exhaust Filter - Model: 849-9365R001 - Serial No.: 232830 - Year: 2006 - Produced a vacuum but failed a PAT test on insulation Additional notes: - All units passed a PAT test except for the Agilent vacuum pump, which failed due to insulation issues. - The Xcalibur unit and Neslab chiller were only visually tested due to larger power plugs. Manuals included: - Oxford Instruments Object Bench Software handbook - Xcalibur Series user manual - Thermo Scientific Recirculating Chiller Operation, Installation, and Maintenance manual - Oxford Diffraction KMC3000C user manual - Oxford Cryosystems Cobra operation guide - Safety Matters cryogenic safety manual - 2 x CrysAlis Pro user manuals - Oxford Instruments Cryojet Controller UMC002 manual - Workstation 4 VMware v4.52 Virtual Machine Software and manual Accessories included: - 1 x set of keys for safety cabinet - 1 x Long Fine Focus unit (Type OD2773/00, No. 163054) - 3 x glass vacuum traps (2 litres approx.) - 2 x vacuum pump platforms - 2 x Parker wound filter cartridges (Part No.: M11R10A) - 2 x Agilent KMW3000 filter cartridges (Part No.: IJ-00-01-002) - 1 x carbon filter nitroflow mobile - 6 x data cables - 4 x Cobra stainless steel line drier units - 1 x 4-way valve purge block - 1 x box of stainless armoured hose pipe and 1/4" plastic tubing

Rigaku X-ray Diffractometer (XRD) Ultima III This system was removed from a university lab where it  (more)was surplus to requirements. The system is in reasonable used cosmetic condition. It has not been powered on at our site due to our on-site risk assessments surrounded X-Rays. Various components and parts are included as listed below, along with a PC setup, although no Rigaku software programs appear to be installed on the PC.However, there are the following software disks included: - Rigaku Basic Software (Cat No.: 9240J101) - Rigaku TTRAX3 and Ultima3 Software (Cat No.: 9240J101) - Rigaku Special Order Software (U30megaP) (Cat No.: 9999) System Specifications: - Model: Ultima III - Cat No.: 2035M410 - Serial No.: DD3654N - 6 Station Holder - Model: SA-HEM3 - Cat No.: 4057J101 - Serial No.: 00563702 - Patlite Beacon - Model: LMS-L (SN-06X03M) - Rigaku DC Motor Controller - SN: DD12866 - Rigaku Long Fine Focus - Type: R01-29-0202 - NC: 9430 022 73201 - No. DK 402688 - Rigaku CBO Cross Beam Optics - Cat No.: 2220B101 - SN: DD12793 - Additional Rigaku parts: - Cat No.: 5738E402 (SN-DD061813) - Cat No.: 2155G101 (SN-DD12804) - Cat No.: 4601K831 (SN-DD12154) - Cat No.: 4253A101 (SN-DD11586 - Vexta Stopping Motor - Model: PK543-A - SN: UR70J32307 PC Setup: - Dell Optiplex 9020 with monitor, keyboard, and mouse - The PC is in working order with all passwords cleared. It contains a few Rigaku files, but no software programs appear to be installed. Included Manuals/Software: - 2 x Rigaku D/MAX 2000/PC Series Instruction Manual - X-Ray Diffractometer Instruction Manual - Rigaku Basic Software (Cat No.: 9240J101) - Rigaku TTRAX3 and Ultima3 Software (Cat No.: 9240J101) - Rigaku Special Order Software (U30megaP) (Cat No.: 9999) Loose spare parts included: - Rigaku Cat No.: 2701E201 (SN-AD08851) - Container of round parts: Rigaku 900003 SH, w/Groove - 2 x Small containers with unknown parts - Scintag Generator Key - Key labeled: "Microscope" - Container of small metals, including: - 1 x Bag labeled "Silicon" - 1 x 640d Silicon Powder - 2 x Tubs UCAR Spectroscopic Powder - 1 x Tub labeled "Tung Flake" - Approximately 20 x small containers of Silicon metal

Rigaku MicroMax-007HF Rotating Anode X-Ray Generator, AFC-11R System Lab This system was removed fro (more)m a university where it was surplus to requirement. All units are in excellent cosmetic condition. This Rigaku X-ray generator is reportedly in working condition according to the previous owner. However, some parts, such as the detector, were removed for spares to keep another system running. No testing was conducted, as the main unit requires a transformed three-phase 400-volt to a 200-volt three-phase supply. Therefore, we cannot confirm its working condition and therefore it is listed as Spares/Repair. This system comprises the following: Rigaku MicroMax-007HFModel RA-MICRO7HFM_RACSerial No. ID211302 The main control system is mounted on a cabinet 100 cm x 60 cm x 90 cm high with a metric 2.5 cm hole spacing isolation tabletop.The operating unit mounted on the table is 40 cm x 30 cm x 55 cm high Rigaku Model AFC-11R detector base and positioning unitSerial No. ID02493 Technifab Products cryogenic sample preparation unit52 cm platform with 9 cm central hole with insulated bung26 cm diameter x 22 cm deep stainless vessel Accessories: 1 x Rigaku Osmic Varimax Optical Fixture Serial No. 25001 x Rigaku Crystallography X-ray XRF Model CU 4364F5012 x Rigaku X-Ray Diffractometer Instruction ManualsSeveral lengths of colour coded 5mm tubing1 x Hampton Research HR4-767 XYZ heated goniometer head1 x Hampton Research HR4-643 XYZ short standard goniometer head1 x PEX4S553B PCB/card to interface with 4 coms sockets

Job Lot of STOE XRD Crystallography Parts Lab These items were removed from a university where they  (more)were surplus to requirement. All XRD items are in reasonably good cosmetic condition, none of them have been powered or tested. The PC has been powered on and has the following software installed:- Winxpow Software No password is required (press 'Cancel' when the computer asks for a password).This PC runs on Microsoft Windows 95. This item is also supplied with various keys and power cables.

Vertex Velp digital thermoregulator The instrument can be combined with the most common heating magn (more)etic stirrers and is supplied ready for use, complete with temperature probe and power cable for direct connection to AREX, AREC.X, AREX-6 heating magnetic stirrers. Thanks to the PW 10 branch element, VTF can be used with all types of heating devices such as water and oil baths, hot plates, thermometers, etc. Temperature Accuracy The VTF thermoregulator can be used in many applications where precision, reliability and flexibility of use are required, as it is equipped with Fuzzy Logic, which allows the thermoregulation to be automatically adapted to different situations, such as power, load and heat loss. The highly sensitive probe offers state-of-the-art temperature control performance, with an accuracy of ± 0.5 ° C Exclusive Fixing System VTF is equipped with an exclusive and innovative integrated fixing system that facilitates the positioning of the Pt100 probe inside the most common beakers. The two lateral clamps allow the height adjustment of the VTF, while the friction system ensures its movement on the horizontal plane. No system will be as comfortable! - Integrated Digital Timer Another unique feature of the VTF is the integrated timer. It is in fact possible to select up to a maximum time of 24 hours and 59 minutes, while at the end of the countdown the instrument will automatically switch off the thermoregulation. The timer mode can be recognized by the alternating flashing of the 2 arrows on the left side of the display. - Technical features: Structure: technopolymer Fixing on rods: from Ø 10 to 13 mm Pt 100 stainless steel probe: length 250 mm and Ø 3 mm Display: LCD Degree of protection CEI EN 60529: IP 54 Power supply: 12 Vdc Weight: 0.3 Kg Dimensions (LxHxP): 75x145x120 mm Adjustment range: -10 ... +300°C Accuracy: ± 0.5°C Resolution: 0.2°C Timed operation: from 0:00 to 24:59 (h: min) Remaining time display: possible Display of maximum temperature reached: possible Display visualization and automatic switching off of the heating plate in case of: - Probe shorted - Probe interrupted

This Zeiss LSM 510 Meta Confocal High Resolution Microscope System was removed from a university lab (more) as it developed a fault. The university reported: "We have a confocal microscope (Zeiss LSM510 Meta) which we are hoping to sell. It powers up but doesn’t fully work, there must be a loose connection somewhere but I don’t have the time or space to work out where." The units are all generally in reasonable used cosmetic condition. All parts do power up individually but we could not get the system to run either. We believe there should be a PC containing software that we do not have. The system is sold for spares/repairs. The system consists of: 1 x Zeiss Axiovert 200M Microscope (1312-732)Fitted with:1 x Zeiss 1269-455 Dual Illumination Source Motorised Mirror Switch.1 x Zeiss 1058-431 Transmitted Light Channel LSM/Pascal.2 x Zeiss 1016-758 W-PI 10x /23 eyepieces.1 x HBO 100 Lamp 098.0042.000 (01/03163).1 x HAL 100 Lamp 42 30 00.With EBQ 100 Isolated Lamp PSU. 1 x Zeiss Laser Module 1294-260.Two of the wheels are broken, so they have all been removed and it has been put on a pallet. 1 x Zeiss LSM510 Meta System.Release 3.5 META 1305-593.With Zeiss Remote 1260-157. 1 x Microscope isolation table. Measures: 150cm L x 80cm W x 77cm H. 1 x Zeiss Temperature Control - 37 (0115.000). 1 x Zeiss AIM-SYSTEM Interface box 2436000101.

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

MT2853 Perkin Elmer API 150 EX LC/MS (liquid chromatography / mass spectrophotometry) Single Quad AP (more)I 150EX The PE Sciex Single Quadrupole API 150EX is a LC/MS Liquid Chromatography Mass Spectrometer. This system can be used in conjunction with various HPLC systems. System is suitable for the analysis of, amongst others, pharmaceuticals, pesticides, proteins and peptides. Machine is complete with : – Heated Nebulizer – Turbo Ion spray – Manuals – Maintenance records – Macintosh Power Mac G3 w. Analyst software (v 1.1) w. back up facilities and libraries. Mass Range: m/z 30 to 3000,  Scan Speed: 2400 amu/sec,  Polarity Switching Speed: + ion to – ion in 700 ms back to + ion in 700 ms,  Dymanic Range: 1 cps to 4 x 10^6 cps (pulse counting),  Mass Accuracy: 0.01% over entire mass range,  Mass Stability: 0.1 amu over 8 hrs,  Mass Resolution: 0.7 ± 0.1 amu at half height,  Dimensions (cm): 52D x 86L x 59H,  Weight: 90 kg, .

Roller mixer with external control for use in an incubator.

Dimensions (HxWxD): 600 x 1200 x 330 mm Internal dimensions (HxWxD): 550 x 570 (x2) x 270 mm