Panalytical Epsilon 1 XRF Analyzer

Job Lot of STOE XRD Crystallography Parts Lab These items were removed from a university where they  (more)were surplus to requirement. All XRD items are in reasonably good cosmetic condition, none of them have been powered or tested. The PC has been powered on and has the following software installed:- Winxpow Software No password is required (press 'Cancel' when the computer asks for a password).This PC runs on Microsoft Windows 95. This item is also supplied with various keys and power cables.

Rigaku MicroMax-007HF Rotating Anode X-Ray Generator, AFC-11R System Lab This system was removed fro (more)m a university where it was surplus to requirement. All units are in excellent cosmetic condition. This Rigaku X-ray generator is reportedly in working condition according to the previous owner. However, some parts, such as the detector, were removed for spares to keep another system running. No testing was conducted, as the main unit requires a transformed three-phase 400-volt to a 200-volt three-phase supply. Therefore, we cannot confirm its working condition and therefore it is listed as Spares/Repair. This system comprises the following: Rigaku MicroMax-007HFModel RA-MICRO7HFM_RACSerial No. ID211302 The main control system is mounted on a cabinet 100 cm x 60 cm x 90 cm high with a metric 2.5 cm hole spacing isolation tabletop.The operating unit mounted on the table is 40 cm x 30 cm x 55 cm high Rigaku Model AFC-11R detector base and positioning unitSerial No. ID02493 Technifab Products cryogenic sample preparation unit52 cm platform with 9 cm central hole with insulated bung26 cm diameter x 22 cm deep stainless vessel Accessories: 1 x Rigaku Osmic Varimax Optical Fixture Serial No. 25001 x Rigaku Crystallography X-ray XRF Model CU 4364F5012 x Rigaku X-Ray Diffractometer Instruction ManualsSeveral lengths of colour coded 5mm tubing1 x Hampton Research HR4-767 XYZ heated goniometer head1 x Hampton Research HR4-643 XYZ short standard goniometer head1 x PEX4S553B PCB/card to interface with 4 coms sockets

Rigaku X-ray Diffractometer (XRD) Ultima III This system was removed from a university lab where it  (more)was surplus to requirements. The system is in reasonable used cosmetic condition. It has not been powered on at our site due to our on-site risk assessments surrounded X-Rays. Various components and parts are included as listed below, along with a PC setup, although no Rigaku software programs appear to be installed on the PC.However, there are the following software disks included: - Rigaku Basic Software (Cat No.: 9240J101) - Rigaku TTRAX3 and Ultima3 Software (Cat No.: 9240J101) - Rigaku Special Order Software (U30megaP) (Cat No.: 9999) System Specifications: - Model: Ultima III - Cat No.: 2035M410 - Serial No.: DD3654N - 6 Station Holder - Model: SA-HEM3 - Cat No.: 4057J101 - Serial No.: 00563702 - Patlite Beacon - Model: LMS-L (SN-06X03M) - Rigaku DC Motor Controller - SN: DD12866 - Rigaku Long Fine Focus - Type: R01-29-0202 - NC: 9430 022 73201 - No. DK 402688 - Rigaku CBO Cross Beam Optics - Cat No.: 2220B101 - SN: DD12793 - Additional Rigaku parts: - Cat No.: 5738E402 (SN-DD061813) - Cat No.: 2155G101 (SN-DD12804) - Cat No.: 4601K831 (SN-DD12154) - Cat No.: 4253A101 (SN-DD11586 - Vexta Stopping Motor - Model: PK543-A - SN: UR70J32307 PC Setup: - Dell Optiplex 9020 with monitor, keyboard, and mouse - The PC is in working order with all passwords cleared. It contains a few Rigaku files, but no software programs appear to be installed. Included Manuals/Software: - 2 x Rigaku D/MAX 2000/PC Series Instruction Manual - X-Ray Diffractometer Instruction Manual - Rigaku Basic Software (Cat No.: 9240J101) - Rigaku TTRAX3 and Ultima3 Software (Cat No.: 9240J101) - Rigaku Special Order Software (U30megaP) (Cat No.: 9999) Loose spare parts included: - Rigaku Cat No.: 2701E201 (SN-AD08851) - Container of round parts: Rigaku 900003 SH, w/Groove - 2 x Small containers with unknown parts - Scintag Generator Key - Key labeled: "Microscope" - Container of small metals, including: - 1 x Bag labeled "Silicon" - 1 x 640d Silicon Powder - 2 x Tubs UCAR Spectroscopic Powder - 1 x Tub labeled "Tung Flake" - Approximately 20 x small containers of Silicon metal

Oxford Diffraction Xcalibur PX Ultra Crystal Diffraction X-ray Generator System This system was remo (more)ved from a university lab where it was surplus to requirements. The system is in very good cosmetic condition, but several units encountered issues during testing, and no PC or control software is included. As such, the system is listed for spares/repair. - Further information regarding issues faced are stated below. The lab stated it had been not used for some time but had some issues. The system units include: - Oxford Diffraction Xcalibur PX Ultra - Serial No.: XXH-127/05 - Year: 2005 - Powered on with mains light, Shutter Closed status light, inner display screen, and hand-held remote keypad all functioning - Oxford Diffraction X-ray Protection Cabinet - Serial No.: XPD-127/05 - Year: 2005 - Thermo Scientific Neslab ThermoFlex 10,000 Recirculating Chiller - Serial No.: 1111473501170217 - Powered on but shut off after 1 second with error code "PHEr" (limit fault) - Oxford Diffraction KMW200CCD CCD Detector Chiller Unit - Serial No.: CCA 73/06 - Year: 2006 - Powered on, but no further testing possible - Oxford Diffraction KMC3000C X-ray Tube Chiller - Serial No.: CAC-142/05 - Year: 2005 - Powered on, pump ran, thermostat seemed functional, but not fully tested - Oxford Diffraction Cryodrive 2.0 - Serial No.: R72-0558 - 6944 running hours - Powered on, but no further testing without gas supply - Oxford Cryosystems Cobra Controller 700 Series Cold Head Controller - Serial No.: 741174 - Powered on, displayed ambient temperature, status lights, and responsive buttons - Parker NitroFlowLab Nitrogen Generator - Model No.: 4278 - Serial No.: 4278-13NFLC0008 - Powered on, displayed a message "writing information to an SD card," and did not allow further actions - Oxford Cryosystems Standard Cobra Nitrogen Control Pump - Serial No.: CB171 - Agilent HS 602 Vacuum Pump with NW25 Oil Exhaust Filter - Model: 849-9365R001 - Serial No.: 232830 - Year: 2006 - Produced a vacuum but failed a PAT test on insulation Additional notes: - All units passed a PAT test except for the Agilent vacuum pump, which failed due to insulation issues. - The Xcalibur unit and Neslab chiller were only visually tested due to larger power plugs. Manuals included: - Oxford Instruments Object Bench Software handbook - Xcalibur Series user manual - Thermo Scientific Recirculating Chiller Operation, Installation, and Maintenance manual - Oxford Diffraction KMC3000C user manual - Oxford Cryosystems Cobra operation guide - Safety Matters cryogenic safety manual - 2 x CrysAlis Pro user manuals - Oxford Instruments Cryojet Controller UMC002 manual - Workstation 4 VMware v4.52 Virtual Machine Software and manual Accessories included: - 1 x set of keys for safety cabinet - 1 x Long Fine Focus unit (Type OD2773/00, No. 163054) - 3 x glass vacuum traps (2 litres approx.) - 2 x vacuum pump platforms - 2 x Parker wound filter cartridges (Part No.: M11R10A) - 2 x Agilent KMW3000 filter cartridges (Part No.: IJ-00-01-002) - 1 x carbon filter nitroflow mobile - 6 x data cables - 4 x Cobra stainless steel line drier units - 1 x 4-way valve purge block - 1 x box of stainless armoured hose pipe and 1/4" plastic tubing

Weighing capacity: 1500/3000/6200 g Readability (0 – 1500 g): 0.01 g Readability (1500 – 3000 g): 0. (more)02 g Readability (3000 – 6200 g): 0.05 g Repeatability (0 – 1500 g): ≤ ±0.01 g Repeatability (1500 – 3000 g): ≤ ±0.01 g Repeatability (3000 – 6200 g): ≤ ±0.03 g Linearity (0 – 1500 g):  ≤ ±0.02 g Linearity (1500 – 3000 g):  ≤ ±0.02 g Linearity (3000 – 6200 g):  ≤ ±0.05 g Response time (average): ≤ 1.5 s Weighing pan: 190 x 204 mm Dimensions (WxDxH): 213 x 342 x 88 mm Weight: 4.7 kg

K.E Developments Cambridge Infrared Chamberscope System This was removed from a university lab where (more) it was surplus to requirements. It is in good cosmetic condition but has not been tested.

Twinbird Corporation SC-UE15R FPSC Module UE15 with Heat Absorption Ring This item was removed from  (more)a university lab where it was surplus to requirements. It is in good cosmetic condition but has not been powered on, as it requires wiring into a power supply. Specifications:- Model: SC-UE15R - Serial No.: 3 5Z16

HX7 H scale’s multi functions Many functions, many interfaces and great robustness (IP66/ IP68 (more)) mean many possibilities for you to use this advanced scale. Tomorrow you can apply it to a different process than today – that’s the multifunctionality. That’s the saving! Use the potential Barcode scanners, receipt printers, label printers, external displays, control buttons, light signalling towers and other controlling/ signalling devices – thanks to multipurpose software, HX7 scale can work with all of them. You can easily connect them thanks to the fact that the balance is equipped with interfaces: RS232, RS485, USB, Ethernet, 4 IN/ 4 OUT. Optionally, the balance can be equipped with 12 IN/ 12 OUT and analog output module. You can find all accessories in our regular offer. And if you have questions about compatibility, our experts will help you. Easy and pleasant Simple and convenient operation with a 7-inch color display. Perfectly visible messages additionally supported by bargraph. The top part of the operation panel features a bar graph consisting of 9 red and green diode fields. The bar graph is a graphic visualisation informing the user on a current net weight of a product presented with reference to the scale range or declared min and max thresholds. The bracket allows the terminal to be placed on any flat horizontal surface or screwed to the wall with adjustable angle. The power of steel The use of stainless steel guarantees you a long life for the scale. It is not afraid of contact with moist objects or accidental splashes. The construction of the scale is made of a stainless steel. This guarantees you work for many years. Not just weighing But also parts counting, dosing, percent weighing and formulations. The power of HX7’s working mods. Do you need ALIBI? There you have it. ALIBI memory is like a black box of a scale. It records all measurements taken on the device. The ALIBI memory cannot be modified or erased. Referring to stored weighings you can generate weighing reports, formulation reports and reports on performed control processes. Single weighing is stored in the ALIBI memory as long as it is specified by a Weighing Storage Period (days) parameter.

Julabo FT902 Immersion Cooler, 115V/60Hz (NRTL Certified) Working Temperature Range -90°C to 30°C R (more)efrigerant R404A/R23 Fluid Type Water, Silicone, Fluorinert/Galden Features - Rapid cooling of liquids down to low temperatures - Counter-cooling of liquids in combination with heating circulators - Environmentally friendly by saving precious tap water - User-friendly operation and handling - Compact design, small footprint - Dry ice substitution - Integrated temperature control and display - With external Pt100 sensor (200 x 6 mm dia., stainless steel) JULABO Immersion Coolers provide counter-cooling when connected to a heating circulator or rapidly cool fluids down to a low temperature. With easy operation the units are suitable for a variety of cooling applications. Units are an alternative to cooling with dry ice or tap water. The FT200, FT400 and F900 units simply turn on and the probe cools. Models FT402, FT902 and FT903 include an external Pt100 sensor and display for input of temperature set point. The FT200 has a 9 cm long x 4 cm diameter cooling dumbell. The FT400 / FT402 have a 12 cm long x 5 cm diameter cooling dumbell. The FT900 / FT902 have a flexible cooling probe 65 cm long / 1.5 cm diameter. The FT903 has a solid coil 2.2″ high and 5.5″ diameter. INCLUDED: The Julabo FT902 Immersion Cooler, 115V/60Hz (NRTL Certified) includes: - Power Cord - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty