BINDER BF-115 incubator / drying oven with forced convection 100°C

FISHER SCIENTIFIC AU125 universal oven / incubator / 200 °C / 125 Litres Maximum temperature: 200 °C (more) Temperature range: Ambient + 5 ° C -> 200 ° C With forced convection FISHERBRAND Capacity: 125 Litres 2 perforated stainless steel shelves Approximate interior dimensions: 500 x 500 x 470 mm Approximate exterior dimensions: 700x 700 x 800 mm (WxHxD) 1500 W / 220V Tested at 50 ° C / 100 ° C / 150 ° C It must be set to 156 ° C to have 150 ° C. It is therefore necessary to add 4% to the desired value. (for example to have 105°C you have to put 109°C) In terms of linearity and fluctuation, it is very good, the temperature fluctuates by more or less 0.3°C light traces inside and the stainless steel exterior walls

Temperature range: +12°C above ambient temperature to 300°C Temperature uniformity at 150°C: ± 2.4 K (more) Temperature fluctuation at 150°C: ± 0.6 K Heating up time to 150°C: 25 min Recovery time after door was opened for 30 s at 150°C: 6 min Air change rate at 100°C: 5 x/h Volume: 741 L Permitted load: 315 kg Internal dimensions (WxHxD): 1000 x 1300 x 574 mm Dimensions (WxHxD): 1160 x 1590 x 816 mm Weight: 166 kg

Thermo Hybaid Maxi 14 Rotisserie Hybridisation Oven This was removed from a university lab where it (more) was surplus to requirements. The unit powers up and has been tested with a digital thermometer (not included). It is in good working order. The shaking plate and Rotisserie shaker are both in good working order. It is in good cosmetic condition with minor marks.

Yamato DKN-302C Programmable Forced Convection Oven 27L, 115V Temperature Range Ambient +10°C to 26 (more)0°C Temperature Distribution Accuracy ± 2.5°C (at 210°C) Chamber Volume 27L Features - Best seller based on excellent performance and affordability - Superior temperature accuracy - DKN302C/312C/402C/412C/602C/612C models come with observation windows - Programmable PID controller for easy program settings (30-step, 3-pattern program controller with repeat functions) - Fixed setting, Quick Auto stop, Auto stop, Auto start, Program operating modes with easy control capabilities - Increased safety and self-diagnostic functions - Overheating prevention and calibration off-set are possible with auxiliary functions - Easy to use and maintain - Built in exhaust ports The Yamato DKN-302C Programmable Forced Convection Oven 27L with extended functions and safety features. Bestseller based on excellent performance and affordability. Superior temperature accuracy. Comes with an observation window. Programmable PID controller for easy program settings (30-step, 3-pattern program controller with repeat functions). Fixed setting, Quick Auto stop, Auto stop, Auto start, Program operating modes with easy control capabilities. Overheating prevention and calibration off-set are possible with auxiliary functions. Easy to use and maintain. Equipped with built in exhaust ports. Operating temp ambient +10~260°C. INCLUDED: The Yamato DKN-302C Programmable Forced Convection Oven 27L, 115V includes: - 2 x Shelves w/ Brackets - Power Cord - Operator's Manual - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

Memmert UN75PA Natural Convection Paraffin Oven 74L, 115V Setting Temperature Range +20°C to +80°C (more) Setting Temperature Accuracy 0.1 °C Chamber Volume 74 L (2.6 cu. ft.) Features - Internal volume of 74 L (2.6 cu. ft.) for versatile storage and heating applications - Temperature range from +20°C to +80°C with 0.1°C accuracy for precision heating - Equipped with dual Pt100 sensors in a 4-wire circuit for reliable temperature monitoring - TwinDISPLAY control panel with high-definition screens and PID microprocessor technology - AtmoCONTROL software for easy programming and data management via USB or Ethernet - AutoSAFETY with integrated over- and undertemperature monitoring and audible alarms - Durable stainless steel interior, reinforced with ribbing and protected large-area heating - Designed with natural convection for uniform heat distribution throughout the chamber The Memmert UN75PA Natural Convection Paraffin Oven 74L, 115V is engineered to provide precise and uniform heating, making it ideal for applications requiring controlled temperature environments. With a spacious 74-liter (2.6 cu. ft.) capacity, it offers a setting temperature range of +20°C to +80°C, maintaining accuracy within 0.1°C, thanks to its dual Pt100 sensors in a 4-wire circuit. The oven’s TwinDISPLAY control panel features high-definition TFT color displays and a digital PID microprocessor for optimal temperature consistency, while natural convection ensures uniform heat distribution without additional airflow disturbances. Enhanced safety features make this paraffin oven reliable for intensive laboratory settings. The AutoSAFETY function includes integrated over- and undertemperature monitors that follow a preset tolerance range, with audible and visual alarms to alert users of temperature deviations. With AtmoCONTROL software for easy programming and data transfer via USB or Ethernet, the oven allows customizable temperature, program time, and time zone settings. Built with a fully insulated stainless steel door, two-point locking system, and a reinforced, easy-to-clean stainless steel interior, the UN75PA is designed for durability and ease of use. INCLUDED: TheMemmert UN75PA Natural Convection Paraffin Oven 74L, 115V includes: - 2 Stainless Steel Grid - Tilt Protection Wall Bracket - Calibration Certificate - Power Cord - Operator's Manual - Manufacturer's Documentation - 3 Year Manufacturer's Warranty

IKA Oven 125 Basic Drying Oven w/ Glass Door Heat Output 1500 W Working Temperature room temp. +5  (more)- 250 °C Operating Area Inner chamber 550 x 525 x 450 mm Features - Temperature range: RT + 5°C to 250°C - Capacity: 125 l - Electronically adjustable ventilation - Clear display and control menu - Key lock function - Timer - Adjustable temperature limit - Glass Door Universal oven for tempering, drying, aging and heating application in the laboratory. The IKA OVEN 125 basic dry covers applications in industry, schools / universities, research, quality control and science. Fast heat up times and a precise temperature control guarantee reproducible test results. A special odorless insulation also ensures lower operating costs. The oven can be controlled by USB and test parameters can be recorded for further analyses. INCLUDED: The IKA Oven 125 Basic Drying Oven w/ Glass Door includes: - IKA Oven 125 basic dry - glass - IO T 1.00 (2x) - Tilt protection (2x) - Screwdriver (for adjustment of temperature limit) - USB cable - Calibration certification - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer Warranty ( + Additional Free 1 Year Warranty Extension with IKA Registration) IKA Oven 125 Basic Drying Oven w/ Glass Door Specifications Heat output1500 WWorking temperatureroom temp. +5 - 250 °CAdjustment and display resolution0.1 KTemperature stability (150°C, center, standard door)0.5 ±KTemperature displayyesTimeryesTimer display7 segment LEDTime setting range1 - 144000 minNumber of trays max. 6Load for one tray max. 30 kgOperating area inner chamber 550 x 525 x 450 mmTotal volume inner chamber125 lAir outlet port diameter inside48 mmDimensions (W x H x D)700 x 825 x 650 mmWeight81 kgPermissible ambient temperature5 - 40 °CPermissible relative humidity80 %Protection class according to DIN EN 60529IP 20USB interfaceyesVoltage220 - 240 / 115 / 100 VFrequency50/60 HzPower input1550 WPower input standby2 WComparison of ModelsSpecificationsIKA Oven 125 BasicIKA Oven 125 Basic w/ Glass DoorIKA Oven 125 ControlIKA Oven 125 Control w/ Glass DoorHeat Output1500 W1500 W1500 W1500 WWorking Temperature RangeRoom temp. +5 - 250 °CRoom temp. +5 - 250 °CRoom temp. +5 - 300 °CRoom temp. +5 - 300 °CTimer Display7 segment LED7 segment LEDLCDLCDTime Setting Range1 - 144000 min1 - 144000 min1 - 142560 min1 - 142560 minInner Chamber (WxDxH)550 x 525 x 450 mm550 x 525 x 450 mm550 x 525 x 450 mm550 x 525 x 450 mmTotal Volume Inner Chamber125 L125 L125 L125 LExternal Dimensions (WxHxD)700 x 825 x 650 mm700 x 825 x 650 mm700 x 825 x 650 mm700 x 825 x 650 mmRS 232 InterfaceNoNoYesYesUSB InterfaceYesYesYesYesVoltage220 - 240 / 115 / 100 V220 - 240 / 115 / 100 V220 - 240 / 115 / 100 V220 - 240 / 115 / 100 V.comparison-table tr td:nth-child(3) { background-color: #fffacd; }

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

The LC-NMR-MS Interface is designed to sit between an HPLC system, an NMR spectroscopy probehead and (more) an MS unit. It would normally be mounted on top of the MS table immediately in front of the MS input connector. The BNMI-HP consists of 3 medium pressure (> 60Bar) syringe pumps, a 1:20 splitter, an 8-Port valve, 3 mixing chambers (T-Pieces) and associated control and interface electronics. The flow of the HPLC separations to the MS unit can be modified by pumping additional solvent from the syringe pumps. This improves the MS peak detection and shortens the time needed for the split separation to reach the MS. Separations can also be stored as a result of an MS peak detection as well as through UV absorption peak detection. The splitter splits the fluid flow from the HPLC in a 1:20 ratio. i.e. ca. 5% of the fluid is directed to the MS and the remainder to either the NMR probehead for immediate analysis or to the BPSU36 storage cassette for storage and later analysis.  The fluid directed to the MS is mixed in the mixing chamber (T-Piece) with the solvent pumped from the syringe pumps. The two left hand syringe pumps pump alternatively to guarantee a constant ’makeup’ flow. The 3rd pump at the right hand side is used to pump a calibration fluid into the flow path to allow the MS to be calibrated (or simply synchronized) at the start and end of each measurement cycle. The 8-Port valve is used to direct the fluid flow. Control of the BNMI Unit is performed using the HyStar program via an ethernet interface. Commands received from HyStar are interpreted in the BNMI Control Board. The control board then sets up the BNMI unit accordingly e.g.: Starts the pumps, changes the flow rate, turns the 8-Port valve. The splitter has a fixed mechanical function and cannot be controlled or adjusted. It simply accepts a fluid flow and splits it into 2 paths in a 1:20 ratio. However, other split ratios are available (for example 1:100 may be preferred if you have very high sample concentrations).

Beam scales H315/4P2 series is stable and proved four load cells weighing solution with more versati (more)le application than standard pallet scales. The adjustable distance between the beams (up to 5 meters) enables fitting the H315/4P2/H scales to different loads (cases, long bars, heavy sections). The load to be weighed can be placed on the beams by a standard fork-lift truck. Beam scales H315/4P2/H series is manufactured in stainless steel version. Optionally, the number of beams in a scale can be increased to 4. Beam scales features handles for easy transporting the scales to its place of use. The scales comes standard with an indicator PUE H315 in stainless steel housing, featuring backlit LCD display and function buttons. The indicator is installed on a long cable. The scale is powered from mains 230V AC, RS 232 interface comes standard. Scales is available in dual range version on surcharge.

C315 Load Cell Platform Scale Precision weight determination in light industrial environments at an  (more)even lighter price. Wherever fast weighing is important. The C315 scale is equipped with the PUE C315 weighing terminal with a backlit LCD display. This long-established technology guarantees reliability and low power consumption, and most importantly, a very long display life. Don’t worry about robustness The construction of the scale is made of powder-coated steel with a stainless steel weighing pan. This guarantees you work for many years, and what’s more, powder-coated steel is more environmentally friendly than traditional painting methods. You will not run out of energy The scale has two power sources: mains and rechargeable. Thanks to its well-designed electronics and LCD display, the device consumes only 5W of energy, which will allow you to work for up to 8 hours without mains power. You get battery power as standard.

HX7 scale’s multi functions Many functions, many interfaces and great robustness (IP66/ IP68)  (more)mean many possibilities for you to use this advanced scale. Tomorrow you can apply it to a different process than today – that’s the multifunctionality. That’s the saving! Use the potential Barcode scanners, receipt printers, label printers, external displays, control buttons, light signalling towers and other controlling/ signalling devices – thanks to multipurpose software, HX7 scale can work with all of them. You can easily connect them thanks to the fact that the balance is equipped with interfaces: RS232, RS485, USB, Ethernet, 4 IN/ 4 OUT. Optionally, the balance can be equipped with 12 IN/ 12 OUT and analog output module. You can find all accessories in our regular offer. And if you have questions about compatibility, our experts will help you. Easy and pleasant Simple and convenient operation with a 7-inch color display. Perfectly visible messages additionally supported by bargraph. The top part of the operation panel features a bar graph consisting of 9 red and green diode fields. The bar graph is a graphic visualisation informing the user on a current net weight of a product presented with reference to the scale range or declared min and max thresholds. The bracket allows the terminal to be placed on any flat horizontal surface or screwed to the wall with adjustable angle. The power of steel The use of stainless steel guarantees you a long life for the scale. It is not afraid of contact with moist objects or accidental splashes. The construction of the scale is made of powder-coated steel with a stainless steel weighing pan. This guarantees you work for many years, and what’s more, powder-coated steel is more environmentally friendly than traditional painting methods. Not just weighing But also parts counting, dosing, percent weighing and formulations. The power of HX7’s working mods. Do you need ALIBI? There you have it. ALIBI memory is like a black box of a scale. It records all measurements taken on the device. The ALIBI memory cannot be modified or erased. Referring to stored weighings you can generate weighing reports, formulation reports and reports on performed control processes. Single weighing is stored in the ALIBI memory as long as it is specified by a Weighing Storage Period (days) parameter.

Corepoint Scientific NSBF231WSW-0 -15C to -35C Single Solid Door Plasma Freezer Temperature Setpoint (more) Range -15°C to -35°C Capacity 23 Cu. Ft. Defrost Method Cycle Optimized, Automatic Features - Provides a spacious 23 cubic feet of storage, ideal for storing a large volume of blood-based products in compliance with FDA and AABB standards. - Features a top-mounted, variable speed compressor with a temperature setpoint range of -15°C to -35°C. - Equipped with seven standard 304 stainless steel drawers that can each hold up to 65 lbs. - Utilizes high-density urethane foam for both cabinet and door, enhancing thermal efficiency and maintaining uniform temperature. - Proportional Integral Derivative (PID) microprocessor with a clear LCD display and °C/°F switchable settings, providing precise control and easy monitoring. - Includes a full suite of alarms such as power failure, temperature sensor failure, and door ajar notifications, ensuring safety and compliance. The Corepoint Scientific NSBF231WSWCR-0 Single Solid Door Plasma Freezer is engineered to meet the rigorous standards required for the storage of blood-based products, conforming to FDA Class II medical device guidelines and AABB requirements. This plasma freezer offers a 23 cubic feet capacity and operates within a temperature setpoint range of -15°C to -35°C, ensuring optimal conditions for the preservation of critical materials. It features seven 304 stainless steel drawers that facilitate organized storage and easy access. The unit is built with high-density urethane foam insulation for superior temperature stability (+/- 0.1°C) and uniformity (+/- 0.7°C), and the exterior is finished in white powder-coated steel for durability. Mobility is enhanced with four swivel casters, front casters locking for secure placement. The plasma freezer includes a keyed door lock for restricted access, ensuring content security. Notable features include a Proportional Integral Derivative (PID) controller for precise temperature management. The freezer uses eco-friendly R600a refrigerant, aligning with EPA SNAP compliance for environmental responsibility. The dimensions of this freezer are 27.8 inches wide, 36.3 inches deep, and 81.5 inches high, and it weighs 360 pounds, making it a robust and reliable solution for any medical or laboratory setting requiring stringent blood storage regulations. INCLUDED: The Corepoint Scientific NSBF231WSW-0 -15C to -35C Single Solid Door Plasma Freezer includes: - 7 Drawers - 4 Swivel Casters - Key for Door Lock - Power Cord - Operator's Manual - 2 Year Manufacturer's Warranty