Felder AF 12 Extraction Unit Lab

This Brook Hansen Motor with Gearbox  Type - 100 was removed from a university lab where it was (more) surplus to requirements. The item is in a reasonable, used cosmetic condition but has not been tested. It requires a 3-phase plug to be fitted. There is no on/off switch so we decided it wasn't safe to power up.

Felder AF 12 Extraction Unit Model: AF-12S/N: 401240/18/189 This was removed from a university works (more)hop where it was surplus to requirements. The unit powers up and is in good working order, the plug has since been removed. Includes dust collection bag.

Job Lot of 21 Boxes of WintWire Welding Wire Size - 3.40 x 1.20 Mild Steel Job Lot of WintWire Weldi (more)ng Wire 21 x Boxes Box info:-CUST No. HPWAAMCast no. 89699Weight - 11.9kgS.O. - 16898/6Size - 1.204 x 3.411 FREQuality - Profile Mild Steel All looks new and unused though a box has been opened for photos.

Pair of Horizon Collators MC-8 MC-8a and MC-8m These were removed from a university lab where they w (more)ere surplus to requirements. Bot units are in reasonably good cosmetic condition and power on, but due to sustained damage, they are not fully operable and therefore, listed as Spares/Repair. The damage sustained is as follows: Part 1:The front intake has completely broken off, with the back tray significantly buckled. Part 2:The rear of the device has sustained severe damage or deformation as a result of mishandling or being dropped. The plugs have since been removed after testing the 32AMP.

Job Lot of WintWire Welding Wire 38 x Boxes Box info:-Order no. HPWAAM - S3Cast no. 017011Weight - 8 (more).4kgTensile - 945 N/mm2Size - 2.50 x 3.50 FREQuality - 1.4034 All looks new and unused though a box has been opened for photos.

Dimensions (WxDxH): 1200 x 870 x 2550 mm Fume cupboard consists entirely of HPL sheets (light blue). (more) Equipped with sink/tap

Balance of the AS X7 series is an advanced analytical weighing device of the SYNERGY LAB line. The A (more)S X7 is exceptional due to a range of modern constructional and system solutions that guarantee reliability, precision and accuracy of measurement, and make everyday operation easy. Ergonomic Mechanical Design The latest AS X7 analytical balance features spacious weighing chamber, and the open-door clearance facilitates easy access to the weighing pan. With this it is possible to use laboratory glassware of various sizes. New aluminium base is a guarantee for weighing system stability. Dual-CLICK system allows tool-free assembly and disassembly of the weighing chamber, and a special design of guides for weighing chamber panes (no rims) makes keeping the device clean convenient. Innovative construction solutions increase balance durability and reliability in long-term operation. Colour Touch Screen The latest generation touch panel of 7” diagonal stands for comfort of operation, even when you have laboratory gloves on. The AS X7 analytical balances guarantee simple and intuitive communication due to wide selection of widgets. The widgets can be freely configured in accordance with user needs. Screen customization favours access to information and results directly from the home screen. The user can configure a complete set of buttons and assign it to a particular operation mode. He(she) can also define info and text fields. LevelSENSING System The in-built sensors measure tilt, and display graphic message on the weighing device screen. In accordance with GLP and GMP, the LevelSENSING system simplifies the adjustment, ensures an ongoing control of the level and informs about deviations. Internal Adjustment Modernized internal adjustment system guarantees accurate indications in extremely unfavourable conditions. SMARTLab AS X7 balances are equipped with a SMARTLab system of an extensive functionality. It ensures support and supervision over the mass measurement process and reduces hazard of error caused by so called „human factor”. Automatic adjustment Regardless of external ambient conditions, the automatic internal adjustment system guarantees 100% efficiency in eliminating balance sensitivity deviations. Sensors Touch-free operation and programmable sensors facilitate daily work and reduce the range of actions performed during the weighing procedure. Alibi memory Data safety is assured with the ALIBI memory, which is integrated into AS X7 balances. The memory enables record of up to 500 000 weighings and guarantees continuity of data collection over a long period of time. Wi-Fi Remote control of the balance via devices, operation of which is based on Android, IPhone, Windows10 systems. Data control Accessing information in the balance depends on the user's permission level. The administrator can manage three different permission levels. Automatic Weighing Records Reports on processes and partial weighings can be generated and sent for archiving via the USB to external devices. Ambient Conditions Monitoring Communication with RADWAG thermo-hygro-barometer allows monitoring of ambient conditions such as temperature and atmospheric humidity. Databases Information system of the AS X7 balances is based on 7 databases that enable operation of many users with numerous products, all the stored data can be subjected to analysis. Weighing data is recorded in 7 databases: • Operators (max 100 entries), • Products (max 5 000 entries), • Weighings (max 50 000 entries), • Packaging (max 100 entries) • Formulations (max 100 entries), • Customers (max 1000 entries), • ALIBI memory (max 512 000 weighings). Additionally it is possible to create formulation reports (max 500 reports). Communication Interfaces The functionality of AS X7 balances can be expanded using the following communication interfaces: USB-A, USB-B, RS 232, DB9 tara/print, Ethernet, Wi-Fi. The additional USB port located on the front of the balance enables easy and fast communication with the USB flash drive, it is possible to connect additional devices via this port too. AS X7 balances are equipped with Kensington Lock, which allows to secure the device against theft. Additional option: Under-pan weighing Weighing instruments purchased after 15th February 2023 will allow under-pan weighing at any time after the purchase. All you need to do is just to order a dedicated hook. THBR 2.0 System Cooperation with THBR 2.0 System for ambient conditions monitoring.

Do you need a moisture analyzer that not only determines moisture or dry matter content with impress (more)ive accuracy, but also performs a digital audit, responds to your voice commands and sends you light messages? If so, learn about the functionality of the ELLIPSIS series of moisture analyzers: It Dries in 4 Ways The MA 5Y Moisture Analyzer offers you four drying profiles: standard, mild, fast and step. The standard profile is the usually used drying profile. It allows the most accurate determination of moisture content. The mild profile is designed for drying substances that are sensitive to the rapid heat released by the filaments, which heat full power at the initial stage of the process. An example of such a substance is leather. You will use the fast profile for samples with significant moisture content – of the order of even several tens of percent. The step profile will be ideal for drying substances that contain more than 15 percent moisture. Within this profile you can define any three temperatures. You will choose the values of temperature and duration of heating experimentally. What Drying Temperature Should I Set? The drying temperature determines the duration of the process. Its value depends on the type of material. If the temperature is too low, it will under-dry the sample and, consequently, unnecessarily increase the measurement time, while if it is too high, it will cause a burning effect on the material. The drying temperature for the traditional (oven) method is determined by industry or factory standards. If there are no standards, you will select the temperature experimentally. The maximum drying temperature on the MA 5Y Moisture Analyzer is 160°C. How Do I Finish the Drying? In 4 Ways The MA 5Y Moisture Analyzer has four finish modes: automatic, manual, time-defined and user-defined. Automatic mode You define the moisture loss limit value in 60 seconds. When the moisture analyzer reaches the set criterion, the measurement will automatically end. Manual mode You terminate the measurement yourself by pressing the STOP button. Time-defined mode The measurement ends after the set time has elapsed regardless of the result. You have up to 99 hours 59 minutes to manage! User-defined mode When you remove all volatiles from a sample, by definition, its mass should be constant. During drying, the dry mass of the sample is defined by a condition: if the mass of the sample is stable within 1 mg during the observation time (Auto 1-5), we consider that all volatile components have been removed from its structure. Digital Weighing Auditor Ensures that your moisture analyzer is ready for use. What is more, it informs about the need for a moisture analyzer inspection or a periodic audit of the moisture analyzer’s accuracy and sensitivity. 10-Inch Display Bigger screen – 10’’ – means more information in one place. On the new ELLIPSIS terminal, you will see up to 3 screens, widgets, graphs, statuses, notes, handy measurement history. Uncompromising User Verification For the first time ever, the moisture analyzer will verify the user using a password, RFID card, fingerprint reader, facial recognition mechanism, or any combination of these. Ambient Light – an Innovative Way for the Moisture Analyzer to Communicate With the User The light colour will tell you about status, process results, procedures, or alerts. Hotspot Use the moisture analyzer on any device connected to it. This can be a smartphone, tablet, or computer. RFID ELLIPSIS works with RFID tags* that can be used to tag your products or formulation ingredients in the database. They can also be used to identify a user. Live Note – Note Down Your Conclusions It’s the first time you can add a voice memo to a measurement series or procedure report. If you prefer to write it down, ELLIPSIS allows you to add a text note. Handy Library This is where a series of recent measurements or a report ready for digital signature, according to 21 CFR Part 11, can be found. Widgets Prepared to display what you need most at any given moment. 21 CFR Part 11 Do you work in the pharmaceutical industry? Do you need a digital signature? We are offering the moisture analyzer which as a standalone fully meets the requirements of 21 CFR Part 11/ EU GMP Annex 11. Full data security Electronic signatures Validations Electronic records Audit trails Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13.56 MHz

Scilogex DS-160/T14 Saw-tooth Generator Probe The Scilogex DS-160/T14 Saw-tooth Generator Probe is a (more) specialized tool designed for use with the Benchmark D160 Homogenizer, specifically for homogenizing samples in a volume range of 100 to 1000ml. With dimensions of 14mm x 130mm, this generator is a 14 mm saw tooth attachment that fits easily onto the homogenizer. The saw tooth design ensures efficient and thorough homogenization of samples, while the length of the generator allows for homogenization of larger sample volumes. INCLUDED: The Scilogex DS-160/T14 Saw-tooth Generator Probe includes: - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

Julabo CF31 Cryo-Compact Refrigerated Circulator, 115V/60Hz Working Temperature Range -30°C to 200° (more)C Cooling Capacity 320W at 20°C Refrigerant R134a Features - Ergonomic design and easy operation - Small overall dimensions for lowest space requirement - Splash-proof keypad - Bright VFD display and interactive LCD dialog display - Highly precise ICC cascade temperature control - RS232/RS485 interface for PC connection - Electronically adjustable pump stages - External Pt100 sensor connection - Integrated programmer with 6x60 program steps - Early warning system for low liquid level - 3-point calibration - TCF Temperature Control Features - Adjustable high temperature cut-off - Classification 3 according to DIN12876-1 - Pump connections for external temperature applications - Bath opening for temperature control of small objects in the bath - Front drain The CF Cryo-Compact refrigerated/heating circulators have a very small footprint which is ideal for placing on a benchtop or in a fume hood with limited space. Models feature M16x1 male pump connections for external temperature applications with 8 and 12 mm hose barbs. The HighTech CF31/CF41 units have a working temperature range from -30(-40) to +200°C and include a dual screen display with numeric keypad for easy data entry and instrument reading. RS232 port for external communication and Pt100 sensor connection for external monitoring and control. A 4-speed centrifugal pressure / suction pump provides 22-26 L/min flow with 5.8-10.2 psi pressure / 2.9-5.6 psi suction. Integrated programmer with 6 x 60 program steps. INCLUDED: The Julabo CF31 Cryo-Compact Refrigerated Circulator, 115V/60Hz includes: - 2 Each Barbed Fitting for Tubing 8 and 12 mm Inner Dia. (Pump Connections M16x1 Male) - Power Cord - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty