Autoclave Engineers Model 300mL EZ Seal w/ Control Tower Lab NOTE - THIS IS A SPARES/REPAIRS ITEM

Chamber dimensions (Ø x depth): 500 x 500 mm Capacity: 117 L See for additional info: https://www.sy (more)stec-lab.com/autoclaves/vertical-top-loading-autoclaves-40-150-l/

Convenient effective way to quickly decontaminate your micro-dissecting instruments. No more need fo (more)r messy chemicals or open flames in the lab, and the small footprint saves bench space. Effective when rapid decontamination of micro-dissecting instruments is needed.  The unique stainless steel glass bead bath remains at a constant 260ºC, allowing you to insert the tips of your instruments whenever you wish to decontaminate them. And it’s fast…most micro-dissecting instruments decontaminate within 15 seconds. Operating Temperatue: 260ºC Stainless Steel Well (⌀xH): 50 x 101 mm Suitable Glass Beads: 1.5 mm lead free glass balls Dimensions (HxWxD): 171 x 133 x 133 mm Weight: 2 kg

Priorclave PS/QCS/EV150 Top Loading Autoclave This was removed from a university lab where it was su (more)rplus to requirements. The unit powers up but has a main board fault. It is sold for spares/repairs.

DW Scientific AES Chemunex Masterclave 09 Benchtop Autoclave This was removed from a university lab (more) where it was surplus to requirements. The unit powers up but has not been tested further at our facility. It is sin good cosmetic condition with minor marks.

Boekel Scientific 25515016 Cement Autoclave The Cement Autoclave consists of a welded ASME certified (more) steel cylinder with a bolted cover mounted on a sturdy supporting frame and enclosed in a heat insulated metal housing. The unit is designed to handle pressure in the 60-350 psi (0.4 -2.4 MPa) range and consists of steam vessel, pressure regulator, pressure gauge (0-600psi), air vent valve, power switches, and a safety pop valve set at 350 psi. All components are pressure tested and designed to meet the highest safety standards. The autoclave consists of a welded steel cylinder with bolted cover, mounted on a sturdy supporting frame and enclosed in a heat insulated metal housing. The steel cylinder is fitted with a high temperature gasket and a heavy cover held in place by 16 cap screws bearing upon washers. A T-Handle wrench supplied with the autoclave may be used to tighten the nuts gradually and uniformly to make a leak-proof assembly. The cylinder assembly is designed for a safe working pressure of 525 PSIG, or one and one-half the maximum working pressure. A safety valve set to release at 350 PSIG is provided for protection and modification is not recommended for safe operation. A dial pressure gage indicates the steam pressure in PSIG. Temperature readings are taken with a No. NP22507 thermometer ASTM #2F, which is placed in the thermometer well provided in the cylinder cover. An air-vent valve allows the escape of entrapped air during the early part of the heating period and releases any steam pressure remaining at the end of the cooling period. The autoclave is heated by two electric heaters attached to the cylinder. The heating unit is controlled from a switch panel on the control box. The control box houses the pressureregulator. A main toggle switch controls the entire electrical circuit including the automatic regulator. Separate on-off toggle switches, in series with pilot lights, control the current to the two heating elements. Switch functions are indicated on the switch panel.INCLUDED: The Boekel Scientific 25515016 Cement Autoclave includes: - Wrench, Thermometer, and 5 Gaskets - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

2x EV Sx300 Speakers Lab These items were removed from a university lab where they were surplus to r (more)equirement. They are both in good cosmetic condition, however, we are unable to test them as we do not have the required power supply cables. Power supply cables are not included.

Nikon Eclipse TE300 Inverted Fluorescence Microscope System Lab This was removed from a university l (more)ab where it was surplus to requirements. This system is in good cosmetic condition with all included units in working order. 1 x Nikon Eclipse TE300 body fitted with:1 x Nikon 065851 multi position binocular neck.1 x Nikon manual stage.1 x Nikon filter holder, no filters fitted.1 x Nikon Condenser Turret fitted with 1 x LWD ∞ Ph3 & 1 x Blanking plate.The other 3 blanking plates are missing.1 x Nikon LWD 0.522 x Nikon CFI 10x/22 eyepieces.1 x Nikon Plan Flour20x/0.50Ph1 DLLObjective. 1 x Nikon LHS-H100P-1 Halogen 12v 100w Lamp.1 x Nikon TE-PSE100 Power supply with control cable. 1 x Nikon LH-M100C-1 Mercury 100w Lamp. (Run hours not known, bulb will require replacement).1 x Nikon C-SHG1 Power Supply. (Run time counter reset).

HyClone 50L Single-Use Bioreactor This was removed from a university lab where it was surplus to re (more)quirements. The unit powers up and is in good cosmetic condition with minor marks from use.

Yamato BM-100 Analog Water Bath 4L, 115V Water Tank Capacity 4L Operating Temperature Range Ambien (more)t +5-95°C Temperature Accuracy ±2°C (at 60°C) Features - Analog set up system - Thermometer is included to verify actual temperature - Protected water tank prevents burns caused by contact - CSUS316 pipe heater 500W - Comes with 1 Year Manufacturer's Warranty

Scale WLY for statistic control Scale WLY is intended to fast and precise determination of mass in l (more)aboratory and industrial conditions. The model line is the response for growing market demands concerning simple operation and maximum automation of the weighing process. The scales enables cooperation with barcode scanner, printer, label printer, RFID readers and standard PC devices (mouse, keyboard, USB storage device). Design and functionality All WLY scales is equipped with stainless weighing pan, TFT 5,7'' colourful touch screen and membrane keyboard. As an option the scale enables connection of an additional weighing platform to the terminal. The following functions are available: programmable proximity sensors, programmable printout templates, programmable text information for scale's operation, printouts. Scale WLY/PGC is equipped with modules that put packaged products control into practice. The module is supported by database containing products and operators lists. A control started by the scale is automatically stopped after controlling pre-defined quantity of packages (samples). Number of the packages is fixed by scales program depending on product batch size. Scales are equipped with 5,7" colourful, graphic touch screen display for previewing information concerning currently performed control and its result. Scale requires two staged verification process. Due to the influence of gravitational acceleration force the scale has to be adjusted on use site. Control cycle runs according to the following scheme: operator choice, product choice, control start, acquiring weighing records, automatic control end after certain packages number, control report print. Each carried out control is ended with a final report containing all information that is necessary for pre-packaged products control report. The report is automatically saved in scale memory and at the same time it can be printed by printer connected to scale. Scale coupling with computer program enables: keeping weighing records from successive weighments in the database, automatic printout of control processes from computer software level, sending user defined codes from scale to computer software; the codes match weighed product (product code, operator code, batch quantity, batch no., control Start/Stop), defining product codes and their descriptions (names) from the level of computer program, therefore user can assign an individual product name suitable for the company's branch. The purpose of the scale is the packaged goods control (PGC), so remember that verification (legalization) is necessary. We recommend ordering a scale with a proper verification (legalization).