Leica TCS SP 2 Confocal Microscope System - PC Comms Fault Lab NOTE - THIS IS A SPARES/REPAIRS ITEM

This was removed from. a university lab where it was surplus to requirements. It seems there are som (more)e parts missing. What is included is listed below; Table/Rack on wheelsDimensions - L111 W70 H62cm Fitted inside:-Carl Zeiss ECU-LSM 5 Live PC - Powers on but the Hard drive has been removed. Carl Zeiss LSM 510 META Laser Head Casing - The casing is in bits and it looks like there are parts missing Carl Zeiss Remote for LSM 510 R3.5/LSM 5 Live Box full of all the connection cables Keyboard & Mouse Box of small parts/accessories including:-Software discs and Fujitsu Recovery DVD'sCarl Zeiss MicroImaging LSM 510 META 4.0 Software DongleSeveral USB CablesLots of small parts/accessories

This Leica TCS SP 2 Confocal Microscope System was removed from a university lab due to a fault. The (more) university reported "Apparently it was a computer issue, in that the computer failed and would no longer talk to the confocal and nothing could be done to remedy the issue since Leica wont support it, I’m told the actual microscope and lasers are fine (if old!)" From our assessment, the microscope appears to be fully working and it could be split from the main system and used on its own. The controllers etc for the automated stage also appeared to work fine. It is just the AOBS head and control system that doesn't want to communicate with the PC. The system has been fully connected up at our facility. We have replaced the PCi card but that did not generate any success either. When starting the Leica PC program it shows the following message: "AOBS Crystal Ctrl (2)" reports 0 unlocked PLL channel(s)! Please lock channel(s) or reset controller. The AOBS is the scanner head which is attached to the main control desk. We have also tried the system with another identical head that we have in stock. That gave us exactly the same result. It is sold for spares/repairs. Please note that the marble table in the photos was retained by the lab.

Leica Microsystems Type - TCS SP2 Confocal Microscope System This was removed from a university lab  (more)where it was surplus to requirements. What is included is in good working order, but the system is not complete. It is missing the following; Table topCooling unitMicroscope isolation tableCameraFlexi tube for prior unit.Bulb for prior unit.There may be more missing parts, but we are unable to confirm. It is in good cosmetic condition with minor marks. Included are; Leica TCS SP2 MicroscopeModel: RCS SP2Serial#: 142400026 Attached to microscope:Leica ∞/0.17/E HCX PL APO 40x/1.25-0.75 OIL CS Leica ∞/-/C HC PL APO 20x/0.75 Leica ∞/0.17/E HC PL APO 10x/0.40 CS 2 x Eyepieces HC PLAN S 10x/22 Leica Condenser 0.53 S 23 (521500)Leica C Mount Adaptor 0.5x : 1/2" = 16 (541511) All other items included: Prior Lumen200Model: L200/CSerial#: 70808 Ernst Leitz Wetzlar GmbhType: 307-072.45Hg 100 W Bulb Leica Power Supply for DiodeLaser COH 405nm, 25mWPart#: 1530910001 03 Leica DM R ManualLeica Confocal SoftwareLeica TCS User Manual Leica PC with Software installed. Leica Dust cover for Microscope and PC.

Zeiss LSM 510 Meta High Resolution Confocal Microscope System This was removed from a university lab (more) where it was surplus to requirements. The units are all generally in reasonably good used cosmetic condition. All parts do power up individually but we could not get the system to run. We believe there should be a PC containing software that we do not have. The lab believed it was suitable to sell only for spares/repairs. The system consists of: 1 x Zeiss Axioskop 2 FS mot Microscope (452314)Fitted with:1 x Zeiss LSM 510 Meta VIS/NLO 1305-590 Scan Head. 1 x Zeiss 1320-560 Fitted with:1 x HBO 100 Lamp1 x Zeiss NDD2 1104867 Detection Module.1 Zeiss NDD3 1104-867 Detection module. 1 x Zeiss 1269-455 Switching Mirror, Fitted with:1 x HAL 100 Lamp1 x Zeiss 1058-431 Transmitted Light Channel LSM/Pascal. The following filter cubes are fitted: 1 - None2 - FITC3 - unreadable4 - DAPI5 - NDD The following objectives are fitted: 1 x Zeiss W Plan-APOCHROMAT421462-990040x/1.0 DIC VIS-IR∞/0 1 x Zeiss 44 00 39ACHROPLAN10x/0,30w Ph1∞/0 2 x Carl Zeiss W-Pl 10x/23 1016-758 Eyepieces. 1 x Zeiss Laser Module RGB 1373-790.Unit appears to be dated Nov 07. 1 x Zeiss Remote LSM 510 R3.5/LSM LIVE 1260-157. 1 X LUIGS & NEUMANN Microscope Remote. 1 x Carl Zeiss 1128-574 SNT 12V 100W Power Supply. 1 x HBO 100 Power Supply. 1 x Carl Zeiss 1298-260 Safety Box. 1 x LASERMODUL NIR. 1 x Carl Zeiss RT-PC 2720.Not sure if this is a spare for the one inside the LSM unit?It does power up and run. The white bench is not included.

Olympus Lext OLS3100 Confocal Microscope w/ MM6-ASPS Controller & OLS3000 PSU This was remo (more)ved from a university lab where it was surplus to requirements. All parts power on and appear to be in working condition. The control unit and emergency stop button are working correctly. The stage control appears to be working correctly with a smooth motor. Only the cables shown are included. The system is in good cosmetic condition, but the rubber foot ends are crumbling. There is no software included with the system. Items included:Main Units:Olympus Lext OLS3100Dimensions: 464(W)x559(D)x620(H)mmWeight: 56.5kg Olympus MM6-ASPS ControllerDimensions: 381(W)x304.8(D)254(H)mmWeight: 14.33kg Olympus OLS3000 Power SupplyDimensions: 355.6(W)x177.8(D)355.6(H)mmWeight: 9kg Accessories:Olympus U-DICROlympus U-P03Olympus U-AN360-3

If you buy a High Resolution Scale HY10 by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. Fast and Stable Measurement The scale displays the final result even in one second. High Maximum Capacity and Accuracy in a Single Device On the large weighing pan of an HRP scale, you can weigh a load of 150 kg with a readability of 1 g and impressive repeatability. Minimum Eccentricity Error Over the Entire Range On the HRP scales, you can also weigh irregularly shaped items with a centre of gravity significantly displaced from the weighing pan axis. Parameter Stability Over Time and After Transport Retain the correct metrological parameters even after prolonged, intensive use and transport of the scale due to its resistant and robust mechanical design. Weighing Pan Dimensions Adapted to the Accuracy of the Balance Weigh with the highest readability of 0.02 g on the 360 x 280 mm weighing pan and with a readability of 20 g on the 1,250 x 1,000 mm weighing pan. Maximum Robustness IP 67 platforms with additional sealing elements to protect against dust, dirt and moisture and can be cleaned with a pressure washer. New, lmproved MONOBLOCK® The new, taller and larger MONOBLOCK® enables the best repeatability and speed in its class of weighing platforms. New HRP Platform HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. Readability of 0.01 g at 10 kg maximum capacity and 0,2 g at 120 kg maximum capacity. Repeatability down to 0.01. Higher resistance to changes in ambient conditions. The platforms are so robust that they can be cleaned with a pressure washer. Transport protection that stiffens the structure during transport, eliminating any unwanted stresses. Platforms with a maximum capacity starting at 300 kg include transport handles, which makes them easy to move. Platforms of IP 67. PUE HY10 Terminal HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. High Level of Protection HRP scales have additional sealing elements to protect them from dust, dirt and moisture. This allows them to be cleaned with a pressure washer.

THE TOP MODEL OF THE 5 SERIES Ideal for laboratories requiring precise sample temperature control an (more)d maximum reproducibility. The AREX 5 Digital magnetic stirrer is a beautiful instrument with a dual digital display for thermoregulating samples with an accuracy of ± 1.0 °C. Thanks to the VTF system then, it will be possible to achieve an accuracy of ± 0.5°C. Pt100 and Pt1000 probes are also available as an option. RESISTANCE, SAFETY AND PERFORMANCE The plate of the AREX 5 Digital Velp model is IP42 certified and is made of aluminum alloy coated with a ceramic layer, which guarantees protection from scratches and chemical agents, making it very resistant and easy to clean. It is therefore preferred in laboratories where acids, bases and solvents are used. Safety circuits and overtemperature protection guarantee complete protection for the operators. Two light indicators inform the user when the heating function is active. Even when the instrument is switched off, a safety message ('HOT') remains on the display until the plate temperature drops below 50°C. A further alarm will detect the presence of the probe. The plate structure and the insulating disc protect the internal parts and ensure high resistance to the most demanding laboratory environments and applications, for example when working with cold fluids (below 0°C). AREX 5 is designed to last over time and like most Velp products it is guaranteed for 3 years. THERMOREGULATION When a temperature probe is connected, it is possible to choose 2 different thermoregulation modes to satisfy all laboratory needs: - FAST: the set temperature is reached quickly - FINE: the set temperature is reached more slowly, minimizing the overshoot SHAKING AREX 5 is equipped with a powerful brushless motor for daily applications, being able to agitate up to 20 liters (H2O). It is also equipped with SpeedServo™ technology, which allows the speed to be kept constant even when the viscosity of the sample varies. The combination of the powerful brushless motor and the strong magnetic coupling ensure homogeneous stirring, even in the peripheral areas of the plate, guaranteeing a constant speed in all positions. DESIGN The compact, innovative and attractive design offers comfort and safety both during benchtop applications and in laboratory fume cupboards. The inclination of the front panel is designed to optimize the user experience and the bright LED display allows easy reading and constant monitoring of the temperature and stirring speed. APPLICATIONS AREX 5 is the ideal solution for temperature sensitive applications in many industrial, research and academic laboratory sectors. THE AREX DIGITAL PANEL: BEAUTIFUL AND SIMPLE TO USE By turning the left knob it will be possible to adjust the temperature up to 310°C, while with the right one it will be possible to set the stirring speed from 50 to 1500 rpm. COMPARISON TABLE OF THE NEW VELP SERIES 5 MAGNETIC STIRRERS:

Jouan CR 412 Centrifuge This unit was removed from a university where it was surplus to requirement. (more) This item is in reasonably good cosmetic condition. It powers on, but the button functions are unresponsive to the unit, therefore unable to conduct any testing. The lid opened with manual emergency release. It is sold as Spares/Repairs. Includes the following: 2x Swinging Buckets:Part no: 11174154Volume: 450ml Bucket Vial Adaptor Inserts:1x set 7x 50ml vials - RED1x set of 7x 15ml / 16x 6ml vials - BROWN

Torrey Pines Scientific Inc Echotherm Heating/Chilling Plate IC22-2 This item was removed from a uni (more)versity where it was surplus to requirement. The unit powers up and is in good working order. It was tested with a digital thermometer (not included). It is in good cosmetic condition.

Applied Biosystems 7500 Fast Real Time PCR System This was removed from a university lab where it w (more)as surplus to requirements. The unit powers up and has passed all hardware testes. The lamp is showing 2029 hours. It is communicating with the Windows 7 PC which has ABI Life v2.3 installed. It is in excellent cosmetic condition with minor marks from use. With it are; 1x Dell PC:Model Optiplex 7010 1x Iiyama Prolite MonitorModel B2282HS21.5 inch screen 1x Dell Keyboard:The unit is in good working and cosmetic condition. 1x Dell Mouse:The unit is in good working and cosmetic condition. Connecting cables.

F1 Mass Standard - knob weights without adjustment chamber - set (1 g - 2 kg), plastic box Number of (more) pieces in the set: 15