Confocal microscopes

This was removed from. a university lab where it was surplus to requirements. It seems there are som (more)e parts missing. What is included is listed below; Table/Rack on wheelsDimensions - L111 W70 H62cm Fitted inside:-Carl Zeiss ECU-LSM 5 Live PC - Powers on but the Hard drive has been removed. Carl Zeiss LSM 510 META Laser Head Casing - The casing is in bits and it looks like there are parts missing Carl Zeiss Remote for LSM 510 R3.5/LSM 5 Live Box full of all the connection cables Keyboard & Mouse Box of small parts/accessories including:-Software discs and Fujitsu Recovery DVD'sCarl Zeiss MicroImaging LSM 510 META 4.0 Software DongleSeveral USB CablesLots of small parts/accessories

This was removed from. a university lab where it was surplus to requirements. It seems there are som (more)e parts missing. What is included is listed below; Table/Rack on wheelsDimensions - L111 W70 H62cm Fitted inside:-Carl Zeiss ECU-LSM 5 Live PC - Powers on but the Hard drive has been removed. Carl Zeiss LSM 510 META Laser Head Casing - The casing is in bits and it looks like there are parts missing Carl Zeiss Remote for LSM 510 R3.5/LSM 5 Live Box full of all the connection cables Keyboard & Mouse Box of small parts/accessories including:-Software discs and Fujitsu Recovery DVD'sCarl Zeiss MicroImaging LSM 510 META 4.0 Software DongleSeveral USB CablesLots of small parts/accessories

This was removed from a university lab where it was surplus to requirements. All units are in good u (more)sed cosmetic condition but they do have various signs of general use. The system consists of: 1 x Bio-Rad Radiance 2000 Laser Scanning System.1 x Bio-Rad Motorised Focus Unit.1 x Bio-Rad Optical Unit. All of the rubber on the wheels of the Radiance has broken off. The wheels do still roll though. The Bio-Rad Radiance 2000 powers up fine, but was not tested any further.

This Leica TCS SP 2 Confocal Microscope System was removed from a university lab due to a fault. The (more) university reported "Apparently it was a computer issue, in that the computer failed and would no longer talk to the confocal and nothing could be done to remedy the issue since Leica wont support it, I’m told the actual microscope and lasers are fine (if old!)" From our assessment, the microscope appears to be fully working and it could be split from the main system and used on its own. The controllers etc for the automated stage also appeared to work fine. It is just the AOBS head and control system that doesn't want to communicate with the PC. The system has been fully connected up at our facility. We have replaced the PCi card but that did not generate any success either. When starting the Leica PC program it shows the following message: "AOBS Crystal Ctrl (2)" reports 0 unlocked PLL channel(s)! Please lock channel(s) or reset controller. The AOBS is the scanner head which is attached to the main control desk. We have also tried the system with another identical head that we have in stock. That gave us exactly the same result. It is sold for spares/repairs. Please note that the marble table in the photos was retained by the lab.

Leica Microsystems Type - TCS SP2 Confocal Microscope System This was removed from a university lab  (more)where it was surplus to requirements. What is included is in good working order, but the system is not complete. It is missing the following; Table topCooling unitMicroscope isolation tableCameraFlexi tube for prior unit.Bulb for prior unit.There may be more missing parts, but we are unable to confirm. It is in good cosmetic condition with minor marks. Included are; Leica TCS SP2 MicroscopeModel: RCS SP2Serial#: 142400026 Attached to microscope:Leica ∞/0.17/E HCX PL APO 40x/1.25-0.75 OIL CS Leica ∞/-/C HC PL APO 20x/0.75 Leica ∞/0.17/E HC PL APO 10x/0.40 CS 2 x Eyepieces HC PLAN S 10x/22 Leica Condenser 0.53 S 23 (521500)Leica C Mount Adaptor 0.5x : 1/2" = 16 (541511) All other items included: Prior Lumen200Model: L200/CSerial#: 70808 Ernst Leitz Wetzlar GmbhType: 307-072.45Hg 100 W Bulb Leica Power Supply for DiodeLaser COH 405nm, 25mWPart#: 1530910001 03 Leica DM R ManualLeica Confocal SoftwareLeica TCS User Manual Leica PC with Software installed. Leica Dust cover for Microscope and PC.

Leica DM2500 Confocal Microscope System w/ Application Suite X Software Lab This system was removed  (more)from a laboratory where it was surplus to requirements. The client has stated the following: "The systems are fully working and Leica still offer user support for the systems if the new owners so wish. "The system is in good cosmetic condition. All units power up and communicate through the included Leica Application Suite X software.However, there is no camera included, so microscope images cannot currently be viewed via the PC. The system consists of: - 1 x Leica DM2500 microscope - Fitted with: - 1 x Leica 1531144511 Stage - 1 x Leica 11504058 Lamp - 1 x Leica 15-6504-202 Light Supply - 1 x Leica 1531323 Mirror Junction Box - 2 x Leica 507802 HC PLAN 10x/20 Eyepieces - 1 x Leica 507902 ACS APO 10x/0.30 CS Objective - 1 x Leica 507900 ACS APO 63x/1.30 OIL CS Objective - 1 x Leica EL6000 BZ02 with Lightpipe (LCD screen may be faulty, lamp timer not functional) - 1 x Leica TCS SPE Laser Head with Leica Supply Unit RGBV - 1 x Life Imaging Services 'the box' environmental chamber (with 2 x hoses) - 1 x Speirs Robertson Isolation Plate (75cm x 90cm x 5.5cm) - 1 x HP Z420 PC with 2 x Monitors, Keyboard & Mouse (running Leica Application Suite X 3.1.2.16221) - Includes Leica TCS SPE to SPE II USB licence stick

Zeiss LSM 510 Meta High Resolution Confocal Microscope System This was removed from a university lab (more) where it was surplus to requirements. The units are all generally in reasonably good used cosmetic condition. All parts do power up individually but we could not get the system to run. We believe there should be a PC containing software that we do not have. The lab believed it was suitable to sell only for spares/repairs. The system consists of: 1 x Zeiss Axioskop 2 FS mot Microscope (452314)Fitted with:1 x Zeiss LSM 510 Meta VIS/NLO 1305-590 Scan Head. 1 x Zeiss 1320-560 Fitted with:1 x HBO 100 Lamp1 x Zeiss NDD2 1104867 Detection Module.1 Zeiss NDD3 1104-867 Detection module. 1 x Zeiss 1269-455 Switching Mirror, Fitted with:1 x HAL 100 Lamp1 x Zeiss 1058-431 Transmitted Light Channel LSM/Pascal. The following filter cubes are fitted: 1 - None2 - FITC3 - unreadable4 - DAPI5 - NDD The following objectives are fitted: 1 x Zeiss W Plan-APOCHROMAT421462-990040x/1.0 DIC VIS-IR∞/0 1 x Zeiss 44 00 39ACHROPLAN10x/0,30w Ph1∞/0 2 x Carl Zeiss W-Pl 10x/23 1016-758 Eyepieces. 1 x Zeiss Laser Module RGB 1373-790.Unit appears to be dated Nov 07. 1 x Zeiss Remote LSM 510 R3.5/LSM LIVE 1260-157. 1 X LUIGS & NEUMANN Microscope Remote. 1 x Carl Zeiss 1128-574 SNT 12V 100W Power Supply. 1 x HBO 100 Power Supply. 1 x Carl Zeiss 1298-260 Safety Box. 1 x LASERMODUL NIR. 1 x Carl Zeiss RT-PC 2720.Not sure if this is a spare for the one inside the LSM unit?It does power up and run. The white bench is not included.

Olympus Lext OLS3100 Confocal Microscope w/ MM6-ASPS Controller & OLS3000 PSU This was remo (more)ved from a university lab where it was surplus to requirements. All parts power on and appear to be in working condition. The control unit and emergency stop button are working correctly. The stage control appears to be working correctly with a smooth motor. Only the cables shown are included. The system is in good cosmetic condition, but the rubber foot ends are crumbling. There is no software included with the system. Items included:Main Units:Olympus Lext OLS3100Dimensions: 464(W)x559(D)x620(H)mmWeight: 56.5kg Olympus MM6-ASPS ControllerDimensions: 381(W)x304.8(D)254(H)mmWeight: 14.33kg Olympus OLS3000 Power SupplyDimensions: 355.6(W)x177.8(D)355.6(H)mmWeight: 9kg Accessories:Olympus U-DICROlympus U-P03Olympus U-AN360-3

Leica CTR 6000 TCS SP5 Laser Scanning Confocal Microscope This system was removed from a laboratory  (more)where it was surplus to requirements. The system powers on, with all units functional, including the stage and light sources. According to the previous owner, the system features a Leica SP5 confocal with 3 PMT and 2 hybrid detectors, along with an FCCS system that includes 2 SPAD detectors. The filters for the detectors are beginning to delaminate and will need replacing. The SP5 computer is relatively new and has been updated to Windows 10. A full environmental chamber for temperature and CO2 control is also included. The system consists of: - TCS SP5 Control Desk, Microscope, and Scan Unit (Serial No. 510000038, Year: 2007) - Leica CTR 6000 Controller (Serial No. 280210) - Leica CMS Detection Unit (Part No. BS054407) - Leica APD Detection (Serial No. 65031) - Leica Scan Head/Trigger Box (Serial No. 0051) - Leica Switch Console V3 (Serial No. 0028960) - Leica Cooling Fan and Flexible Duct (Part No. 1531229001) - Leica Mercury Lamp Box (Type 11307072071/BZ) - LEJ Mercury Bulb Controller (Type ebq 100mc-L, Serial No. 06 2380802161, 217 hours bulb run time) - Leica Stage Controller (Part No. 11505180) - The Box polycarbonate microscope enclosure - The Cube CB02A Enclosure Heater with probe (Serial No. 10585) - The Brick Air Humidity and CO2 Regulator (Serial No. 10654) - Gecomp PC running Windows XP Pro (Serial No. 071362) - HP Z4 PC running Windows 10 (Serial No. CZC026C55L, Product No. 1JP11AV) - 2 x NEC 1990SXi Monitors (Serial Nos. 6Z009731YB, 6Y008209YB) - Cherry Keyboard (Model MY 3000 USB, Serial No. G0006934) - HP KB-1469 Keyboard (Serial No. 803180-L31) - 2 x HP Mice (Part Nos. 672651-001, 458407-002) The microscope is fitted with five objectives: - Leica 784 HCX PL APO 100x/1.4-0.7 oil cs - Leica 510 HCX PL APO 63x/1.4-0.6 oil cs - Leica 214 HCX PL APO 20x/0.70 1MM corr bl - Leica 506251 HCX PL APO 40x/1.25-0.75 oil - Leica 506279 HCX PL APO 63x/1.2 W corr cs Additional components: - Twin binocular eyepieces HC PLAN s 10x/125 M - 7 x colour filter and mirror blocks, 2 x filter block covers - 12 x stage parts - 1 x humidity water cylinder for The Brick Included Software & Manuals: - Leica Software Discs: Confocal Software v. 2.585 (2x), LAS AF v. 2.73-9723, SP5 WS Premium Recovery, SP5 SP8 Standard G4 Recovery W10, SP5 Workstation Recovery - 2 x copies of Windows XP Professional OS - Manuals: Newport PR 50 compact high-speed rotation stage, Coherent Sapphire 488-20 & 410-10 OEM Laser, The Brick operating manual, The Cube 2 temperature controller manual

If you buy a High Resolution Scale HY10 by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. Fast and Stable Measurement The scale displays the final result even in one second. High Maximum Capacity and Accuracy in a Single Device On the large weighing pan of an HRP scale, you can weigh a load of 150 kg with a readability of 1 g and impressive repeatability. Minimum Eccentricity Error Over the Entire Range On the HRP scales, you can also weigh irregularly shaped items with a centre of gravity significantly displaced from the weighing pan axis. Parameter Stability Over Time and After Transport Retain the correct metrological parameters even after prolonged, intensive use and transport of the scale due to its resistant and robust mechanical design. Weighing Pan Dimensions Adapted to the Accuracy of the Balance Weigh with the highest readability of 0.02 g on the 360 x 280 mm weighing pan and with a readability of 20 g on the 1,250 x 1,000 mm weighing pan. Maximum Robustness IP 67 platforms with additional sealing elements to protect against dust, dirt and moisture and can be cleaned with a pressure washer. New, lmproved MONOBLOCK® The new, taller and larger MONOBLOCK® enables the best repeatability and speed in its class of weighing platforms. New HRP Platform HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. Readability of 0.01 g at 10 kg maximum capacity and 0,2 g at 120 kg maximum capacity. Repeatability down to 0.01. Higher resistance to changes in ambient conditions. The platforms are so robust that they can be cleaned with a pressure washer. Transport protection that stiffens the structure during transport, eliminating any unwanted stresses. Platforms with a maximum capacity starting at 300 kg include transport handles, which makes them easy to move. Platforms of IP 67. PUE HY10 Terminal HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. High Level of Protection HRP scales have additional sealing elements to protect them from dust, dirt and moisture. This allows them to be cleaned with a pressure washer.