Leica CTR 6000 TCS SP5 Laser Scanning Confocal Microscope System Lab

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

This Leica TCS SP 2 Confocal Microscope System was removed from a university lab due to a fault. The (more) university reported "Apparently it was a computer issue, in that the computer failed and would no longer talk to the confocal and nothing could be done to remedy the issue since Leica wont support it, I’m told the actual microscope and lasers are fine (if old!)" From our assessment, the microscope appears to be fully working and it could be split from the main system and used on its own. The controllers etc for the automated stage also appeared to work fine. It is just the AOBS head and control system that doesn't want to communicate with the PC. The system has been fully connected up at our facility. We have replaced the PCi card but that did not generate any success either. When starting the Leica PC program it shows the following message: "AOBS Crystal Ctrl (2)" reports 0 unlocked PLL channel(s)! Please lock channel(s) or reset controller. The AOBS is the scanner head which is attached to the main control desk. We have also tried the system with another identical head that we have in stock. That gave us exactly the same result. It is sold for spares/repairs. Please note that the marble table in the photos was retained by the lab.

Zeiss LSM 510 Meta High Resolution Confocal Microscope System This was removed from a university lab (more) where it was surplus to requirements. The units are all generally in reasonably good used cosmetic condition. All parts do power up individually but we could not get the system to run. We believe there should be a PC containing software that we do not have. The lab believed it was suitable to sell only for spares/repairs. The system consists of: 1 x Zeiss Axioskop 2 FS mot Microscope (452314)Fitted with:1 x Zeiss LSM 510 Meta VIS/NLO 1305-590 Scan Head. 1 x Zeiss 1320-560 Fitted with:1 x HBO 100 Lamp1 x Zeiss NDD2 1104867 Detection Module.1 Zeiss NDD3 1104-867 Detection module. 1 x Zeiss 1269-455 Switching Mirror, Fitted with:1 x HAL 100 Lamp1 x Zeiss 1058-431 Transmitted Light Channel LSM/Pascal. The following filter cubes are fitted: 1 - None2 - FITC3 - unreadable4 - DAPI5 - NDD The following objectives are fitted: 1 x Zeiss W Plan-APOCHROMAT421462-990040x/1.0 DIC VIS-IR∞/0 1 x Zeiss 44 00 39ACHROPLAN10x/0,30w Ph1∞/0 2 x Carl Zeiss W-Pl 10x/23 1016-758 Eyepieces. 1 x Zeiss Laser Module RGB 1373-790.Unit appears to be dated Nov 07. 1 x Zeiss Remote LSM 510 R3.5/LSM LIVE 1260-157. 1 X LUIGS & NEUMANN Microscope Remote. 1 x Carl Zeiss 1128-574 SNT 12V 100W Power Supply. 1 x HBO 100 Power Supply. 1 x Carl Zeiss 1298-260 Safety Box. 1 x LASERMODUL NIR. 1 x Carl Zeiss RT-PC 2720.Not sure if this is a spare for the one inside the LSM unit?It does power up and run. The white bench is not included.

Olympus Lext OLS3100 Confocal Microscope w/ MM6-ASPS Controller & OLS3000 PSU This was remo (more)ved from a university lab where it was surplus to requirements. All parts power on and appear to be in working condition. The control unit and emergency stop button are working correctly. The stage control appears to be working correctly with a smooth motor. Only the cables shown are included. The system is in good cosmetic condition, but the rubber foot ends are crumbling. There is no software included with the system. Items included:Main Units:Olympus Lext OLS3100Dimensions: 464(W)x559(D)x620(H)mmWeight: 56.5kg Olympus MM6-ASPS ControllerDimensions: 381(W)x304.8(D)254(H)mmWeight: 14.33kg Olympus OLS3000 Power SupplyDimensions: 355.6(W)x177.8(D)355.6(H)mmWeight: 9kg Accessories:Olympus U-DICROlympus U-P03Olympus U-AN360-3

Leica CTR 6000 TCS SP5 Laser Scanning Confocal Microscope This system was removed from a laboratory  (more)where it was surplus to requirements. The system powers on, with all units functional, including the stage and light sources. According to the previous owner, the system features a Leica SP5 confocal with 3 PMT and 2 hybrid detectors, along with an FCCS system that includes 2 SPAD detectors. The filters for the detectors are beginning to delaminate and will need replacing. The SP5 computer is relatively new and has been updated to Windows 10. A full environmental chamber for temperature and CO2 control is also included. The system consists of: - TCS SP5 Control Desk, Microscope, and Scan Unit (Serial No. 510000038, Year: 2007) - Leica CTR 6000 Controller (Serial No. 280210) - Leica CMS Detection Unit (Part No. BS054407) - Leica APD Detection (Serial No. 65031) - Leica Scan Head/Trigger Box (Serial No. 0051) - Leica Switch Console V3 (Serial No. 0028960) - Leica Cooling Fan and Flexible Duct (Part No. 1531229001) - Leica Mercury Lamp Box (Type 11307072071/BZ) - LEJ Mercury Bulb Controller (Type ebq 100mc-L, Serial No. 06 2380802161, 217 hours bulb run time) - Leica Stage Controller (Part No. 11505180) - The Box polycarbonate microscope enclosure - The Cube CB02A Enclosure Heater with probe (Serial No. 10585) - The Brick Air Humidity and CO2 Regulator (Serial No. 10654) - Gecomp PC running Windows XP Pro (Serial No. 071362) - HP Z4 PC running Windows 10 (Serial No. CZC026C55L, Product No. 1JP11AV) - 2 x NEC 1990SXi Monitors (Serial Nos. 6Z009731YB, 6Y008209YB) - Cherry Keyboard (Model MY 3000 USB, Serial No. G0006934) - HP KB-1469 Keyboard (Serial No. 803180-L31) - 2 x HP Mice (Part Nos. 672651-001, 458407-002) The microscope is fitted with five objectives: - Leica 784 HCX PL APO 100x/1.4-0.7 oil cs - Leica 510 HCX PL APO 63x/1.4-0.6 oil cs - Leica 214 HCX PL APO 20x/0.70 1MM corr bl - Leica 506251 HCX PL APO 40x/1.25-0.75 oil - Leica 506279 HCX PL APO 63x/1.2 W corr cs Additional components: - Twin binocular eyepieces HC PLAN s 10x/125 M - 7 x colour filter and mirror blocks, 2 x filter block covers - 12 x stage parts - 1 x humidity water cylinder for The Brick Included Software & Manuals: - Leica Software Discs: Confocal Software v. 2.585 (2x), LAS AF v. 2.73-9723, SP5 WS Premium Recovery, SP5 SP8 Standard G4 Recovery W10, SP5 Workstation Recovery - 2 x copies of Windows XP Professional OS - Manuals: Newport PR 50 compact high-speed rotation stage, Coherent Sapphire 488-20 & 410-10 OEM Laser, The Brick operating manual, The Cube 2 temperature controller manual

If you buy a High Resolution Scale HY10 by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. Fast and Stable Measurement The scale displays the final result even in one second. High Maximum Capacity and Accuracy in a Single Device On the large weighing pan of an HRP scale, you can weigh a load of 150 kg with a readability of 1 g and impressive repeatability. Minimum Eccentricity Error Over the Entire Range On the HRP scales, you can also weigh irregularly shaped items with a centre of gravity significantly displaced from the weighing pan axis. Parameter Stability Over Time and After Transport Retain the correct metrological parameters even after prolonged, intensive use and transport of the scale due to its resistant and robust mechanical design. Weighing Pan Dimensions Adapted to the Accuracy of the Balance Weigh with the highest readability of 0.02 g on the 360 x 280 mm weighing pan and with a readability of 20 g on the 1,250 x 1,000 mm weighing pan. Maximum Robustness IP 67 platforms with additional sealing elements to protect against dust, dirt and moisture and can be cleaned with a pressure washer. New, lmproved MONOBLOCK® The new, taller and larger MONOBLOCK® enables the best repeatability and speed in its class of weighing platforms. New HRP Platform HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. Readability of 0.01 g at 10 kg maximum capacity and 0,2 g at 120 kg maximum capacity. Repeatability down to 0.01. Higher resistance to changes in ambient conditions. The platforms are so robust that they can be cleaned with a pressure washer. Transport protection that stiffens the structure during transport, eliminating any unwanted stresses. Platforms with a maximum capacity starting at 300 kg include transport handles, which makes them easy to move. Platforms of IP 67. PUE HY10 Terminal HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. High Level of Protection HRP scales have additional sealing elements to protect them from dust, dirt and moisture. This allows them to be cleaned with a pressure washer.

Weighing capacity: 220 g Minimum Weight (USP, 0.1%, typical): 160 mg Readability: 0.1 mg Repeatabili (more)ty: 0.08 mg Stabilization time: 2 s Calibration: Internal Recommended for: Chemical,Pharma,Food & Beverage Recommended for QC foodstuffs: Yes Weighing pan diameter: 90 mm Dimensions (DxHxW): 344 x 344 x 210 mm

Stainless steel platform scale with four sensors No matter where you place the load on the platform, (more) the result will always be correct. This is due to the four sensors built into the platform. You will appreciate this especially when weighing an irregularly shaped object. It has been with us for years, and will stay for a long time to come The LCD display has accompanied us for long years. During this time it has proven its reliability. It guarantees the readability of the result from many angles and is energy efficient. Inner power No access to mains power? Power failure? No problem. Thanks to its internal rechargeable battery, the H315 scale works anyway (up to 7 hours). Power supply is available at an extra charge. As standard, the scale is equipped with a RS232 cable, to which you can connect most of the accessories from our range. Not just weighing But also parts counting, percent weighing, animal weighing and peak hold. The power of H315’s working mods. Do you require fast and repeatable weight measurement under difficult conditions? The H315 scale is made for that! Work as you like The PUE H315 terminal sits on a 3-meter cable that allows you to hang the terminal on the wall. This allows you to arrange your weighing workplace in many ways. The power of steel The use of stainless steel guarantees you a long life for the scale. It is not afraid of contact with moist objects or accidental splashes. The membrane keyboard is another argument in the discussion of the water resistance of this scale. If you need a dual-range scale, we can make one for you at an extra cost.

Waterproof platform scales H315/HR series is designed for operation in locations with high humidity  (more)or direct contact with water. The scales is easily used in areas with no access to power supply from mains, as it features an internal rechargeable accumulator. Design Single load cell stainless steel platform scales H315 HR series is based on a terminal PUE H315 series. The terminal features large backlit LCD display and function buttons for easy operation. The terminal is installed on a pillar for easy readout of measurement result. Optionally, the scales is offered with indicator installed on a cable for mounting it on a wall. The weighing platform structure is made of stainless steel class AISI 316 with a stainless steel load cell providing the highest IP rating of 68. The scales features RS 232 interface, and optionally an additional display socket. The scales is powered from mains or internal rechargeable accumulator. Optionally, the scales can be powered from mains - 110/120VAC 60Hz (non-standard factory option).

Multifunctional scales TMX H is designed to fast and precise determination of mass in industrial con (more)ditions. TMX H Multifunctional scales TMX H comprises terminal PUE 5 and a weighing platform. Labelling system series TMX H is used to print labels for marking weighted goods e.g. in the process of packing. The program can generate standard labels for single goods. Functionality of the software: a function of weight control (weighing control + / -), previewing weighments carried out on weighing terminal as a table of weighments, simplified reporting module allowing the report to be generated, creation of label templates from labels in weighing terminal, identification of goods by using the code EAN-13 and EAN-128, quick search using the range of barcode scanner, the availability of databases: the operators, products, clients, warehouses, tares (packages), etc. The application enables measurements execution and their record into a local database or on the server. Networked terminals allow transmission of the measurements to the parent database installed on the server. The ability to work with a computer program E2R SYSTEM. Terminal types: PUE 5.15R, PUE 5.19R – resistive touch screen technology. Protection class IP68. High resistance to moisture and dust. In comparison to remaining models, limited brightness and lower resistance to shocks and scratches. Possibility of operation using gloves preventing scratches (latex, material). PUE 5.15IR, PUE 5.19IR – infrared touch screen technology. Protection class IP68. Very high brightness and readability level. High resistance to moisture and dust. High mechanical resistance, possibility of operation using gloves (made of latex, material or even steel chain). PUE 5.15C, PUE 5.19C – capacitive touch screen technology. Protection class IP68. High brightness and readability level. High resistance to moisture and dust, good mechanical resistance. Absolute precision of touch detection, sensing multiple points of touch (multi-touch).

The high resolution MPS module operates on the basis of electromagnetic force converter. The device  (more)may be easily integrated into existing system owned by the customer. Compact design and integrated electronics provide various possibilities of MAS module adaptation into technological lines and installation inside laboratory equipment or devices. Measurements can be carried out using either weighing pan or under-pan weighing system, i.e. solution enabling the load to be suspended beneath the module. By cause of high measurement accuracy, it is recommended to install the module inside customer's device (e.g. in a draft shield) in order to reduce the influence of ambient conditions on the measurement result. The MPS module comes standard with a dedicated power supply. Features: Brand new design of the electromagnetic mechanism housed in an aluminium enclosure, Readability of 0.01 g, Ease of adaptation to the required storage space, Internal adjustment, Various options of hardware configuration. The module has been equipped with RS232 and USB type B interfaces. Dedicated freeware, the R Panel, has been designed to enable control of the module via a computer. It provides access to all the keys and functions available directly from the operation panel, e.g. taring, zeroing, setup, etc. Innovative algorithm for automatic search of electromagnetic weighing modules facilitates connection to a computer. R Panel software makes complete functionality of the R series balances available via the PC. R Panel functionality has been implemented in RLab program as one of its numerous functions.

Corepoint Scientific NSWDUF171JWJ-0 -50C to -86C Upright Ultra Low Temperature Laboratory Freezer, 1 (more)15V Temperature Setpoint Range -50°C to -86°C Capacity 17 cu. ft. Defrost Method Manual Features - Five insulated inner doors - Microprocessor controller specifications - Touch pad keys and four line display for easy programming - Large LED temperature readout - Audible and visual alarms with silence key for audible alarms - Programmable high and low temperature alarm set points - Programmable access code to limit access to set points and controller configuration - Automatic voltage boost to compensate for low line voltages - Normally open, normally closed alarm contacts and 4-20mA signal available to connect to central alarm system - RS-232 serial output - Battery backup on electronics during power outages The Corepoint Scientific NSWDUF171JWJ-0 is an upright ultra low temperature laboratory freezer designed to maintain temperatures between -50°C to -86°C, ideal for demanding cold storage applications. This 17 cu.ft. capacity freezer features a solid swing exterior door with five insulated inner doors, a triple gasket seal, and a vacuum relief port for quick access after door closures. It is equipped with a microprocessor controller, touch pad keys, and a large LED temperature readout for easy programming and monitoring. The freezer includes audible and visual alarms with programmable high and low temperature set points, an automatic voltage boost, and battery backup for electronics during power outages. For security, it offers a programmable access code, a key lock on the cam action handle, and door switch alarms. The interior boasts four heavy-duty stainless steel adjustable shelves and four heavy-duty swivel casters with locks for mobility. Additionally, the freezer uses CFC-free refrigerant and is made in the USA, ensuring high efficiency and low noise operation with two compressors and a 300 BTUh reserve capacity. INCLUDED: The Corepoint Scientific NSWDUF171JWJ-0 -50C to -86C Upright Ultra Low Temperature Laboratory Freezer, 115V includes: - Key for Door Lock - 4 x Adjustable Shelves - Power Cord - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty