VACUUBRAND RC 6 Chemistry-HYBRID Pump

Technical features Flow rate 0.2-1.3 l / min Suction (max.) 3 mWg Operating pressure (max.) 4 bar (r (more)el.) Permitted fluid temperature 5-80°C Maximum permissible viscosity 150 cSt FFKM valve material Membrane material PTFE coating Pump head material PTFE, PP, PVDF Applications Transfer of liquids Qualitative characteristics Small footprint Simple and intuitive use Manual control Self-priming, it can run dry Splash-proof with IP65 protection rating Available with different material configurations for chemical resistance Maintenance free Pump head materials: PP, PVDF, PTFE Membrane material: PTFE coating Valve material: FFKM Simriz® VERSIONS S (standard): the flow rate can only be set manually, using the knob on the upper side, as shown in the photo. RC (remote control): the range can be controlled remotely, such as from a PC, including a fault alarm; a connection cable will be supplied. Supplied with fittings for 8 mm internal diameter tube. NOT SURE WHICH VACUUM PUMP YOU NEED? Try following our guide to KNF pumps: VACUUM PUMPS FOR THE LABORATORY Or download the KNF guide: THE IDEAL DIAPHRAGM PUMP FOR EVERY APPLICATION

The N 840.3 FT.40.18 is a two-stage pump with an integrated “self-drying” system for automatic conde (more)nsate drain. The “SD” series is widely used in laboratories, especially when the vapors are humid and a clean and ecological vacuum is required. Typical applications are: vacuum ovens (for drying chemicals, drying biological samples, heat treatments), autoclaves for sterilizing instruments, containers, filters and textiles. Thanks to the use of anti-corrosion materials, it is possible to vacuum even corrosive products. The heart of the pump is the diaphragm with differentiated structure in PTFE, optimized to guarantee high performance with reduced dimensions and at the same time, long life even in heavy applications. When the humid gases are sucked in, it can happen that condensation forms in the pump head: consequently the performance decreases, considerably increasing the emptying time. To eliminate condensation, the 'drying system' then opens a solenoid valve that allows ambient air to enter the heads. Once the condensation has been eliminated, the solenoid valve closes and the pump sucks from the stove in full capacity. Over time, condensation could form again and then the cycle is repeated. The time interval between one cycle and the next can be adjusted as desired, as well as the duration of the air injection. Technical features Flow Rate (max.) 34 l / min Ultimate Vacuum (max.) 10 mbar (abs.) Pressure (max.) 1 bar (rel.) Permissible Medium Temperature 5-40°C Valve Material FFPM Diaphragm Material PTFE coated Pump Head Material PTFE Applications Rotary evaporation Vacuum oven Qualitative characteristics Clean operation, 100% oil-free Corrosion resistant PTFE / FFPM flow path Ideal for extremely aggressive / corrosive gases and vapors Compact, silent and reliable The self-drying system removes condensation without altering the vacuum level Maintenance free Download the data sheet for further information and accessories. NOT SURE WHICH VACUUM PUMPS YOU NEED? Try following our guide to KNF pumps: VACUUM PUMPS FOR THE LABORATORY Or download the KNF guide: THE IDEAL DIAPHRAGM PUMP FOR EVERY APPLICATION

Heidolph 036150390 Single-Channel Pump Head SP Quick, 1.6mm Features: - Fast and convenient tube cha (more)nges - Low pulsation due to 5 roller system - Pump head features ball bearings - Rollers made of stainless steel - For tubes with a 1.6-mm wall thickness (wt) - Depending on drive and tubing, flow rate ranges from 0.38 to 3,436 ml per minute Click Here to View Product Video INCLUDED: The Heidolph 036150390 Single-Channel Pump Head SP Quick, 1.6mm includes: - 3 Year Manufacturer's Warranty

KNF IP65 FEM 1.02 KT.18RCP Liquid Pump KNF SIMDOS diaphragm pumps offer a variety of options to suit (more) most laboratory liquid metering and dosing needs. The FEM 1.02 KT.18RCP version has a liquid transfer flow rate of 0.03 – 200 mL/min and discreet dosing volumes of 0.03 – 999 mL. It is constructed with the following chemically-resistant flow path materials: polypropylene head, PTFE covered diaphragm, and FFKM valves. The easy-to-read display combined with a touch control knob makes programming and access of all functions very intuitive. Besides onboard manual control, this pump offers analog control, start/stop and reset/prime TTL logic control, output signal fault alarm, and RS 232 PC control. A RC control interface cable and RS 232 cable with D-Sub 9 connector are included. A foot switch for start and stop impulses is available. All SIMDOS pumps are simple and intuitive to operate, compact, and quiet, making them a welcome addition to any business or academic lab. They are effective against pressures of up to 85 psig and transfer viscous media up to 500 centistokes (reduced flow rate above 150 cSt). The integrated software permits the transfer parameters to be modified for a range of different viscosities at the touch of a button. With a durable and IP65 splash-proof design, these pumps are maintenance free, and provide trouble-free ±2% accuracy and ±1% repeatability performance. SIMDOS 02 pumps are self-priming up to 6.6 feet of water, and can run dry indefinitely without damage. Also, unlike peristaltic pumps, there are no troublesome tubing to break or fatigue. INCLUDED: The KNF IP65 FEM 1.02 KT.18RCP Liquid Pump includes: - Power Cord - Operator's Guide - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Applikon Biotechnology EZ-Control Z310110010 Bioreactor System This was removed from a laboratory w (more)here it was surplus to requirements. Included are; Applikon Biotechnology EZ-Control Bioreactor SystemCat no. Z310110010SN - P18662/39Unit dimensions - L41 W37 H72cmThe unit powers on and boots up. Parts:-Applikon Type P100eCat no. Z510000010SN - P323750/22 Applikon Water Console Applikon 7L Glas Biorector Vessel with Heat jacket Trolley Dimensions - L108 W61 H144cmBottom Shelves - 70 x 59cm Consumables/Accessories:-Applikon 20L Appliflex Reusable pH & DO Sensors Cat no. Z650002040Applikon 10L Appliflex Reusable pH & DO Sensors Cat no. Z650001040Box of 2 x AppliSens Sensor ProbesBox of 1 x AppliSens Sensor ProbeMembrane Kit Z110000426Ethernet cableVarious metal partsApplikon Slotted Blindstopper M18 X 1.52 x Applikon Air Inlet Pipe+Porous Sparger 7LApplikon Ribbed Blindstopper M30X1Applikon Assembly Holder M10Ass holder 6mm tube M18x1.5Various probe cablesApplikon Licence file EZ Control + Manuals Dongle Z310110010Heat Jacket - Powers on and heats up

Labconco CentriVap Complete Acid-ResistantVacuum ConcentratorTheall-in-one CentriVap Complete Vacuum (more) Concentrator houses every component youneed to begin processing multiple samples; vacuum concentrator, -50C coldtrap, diaphragm pump, rotor and CentriZap strobe light. Just add your samplesin the containers of your choice and start concentrating. Using centrifugalforce, vacuum and controlled heat, the CentriVap Complete speeds concentrationof samples used in a variety of applications found in molecular biology,proteomics, genomics, cell biology, microbiology, biochemistry, drug discoveryand analytical chemistry.Acid-resistantmodels are available for corrosive chemical use. Other models feature HeatBoost, which surrounds the chamber wall, to further speed evaporation of highboiling point solvents. Click Here to View Product Video INCLUDED: The Labconco 7315021 CentriVap Complete Acid-ResistantVacuum Concentrator, 115V, 60Hz includes: - Coupling Insert - Rotor, 12-13 mm - Glass Jar - Power Cord - Operator's Guide - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

Vacuum systems are widely used for the aspiration and disposal of liquid waste, for instance, when r (more)emoving media from cell cultures, supernatant after centrifugation, and wash solutions from immunoassay well plates. The aspiration of waste liquids is a routine yet time-consuming task. The user-friendly VACUSAFE system streamlines this repetitive workflow, freeing up lab personnel to perform other vital tasks. It also provides a secure alternative to do-it-yourself liquid waste disposal systems typically found in laboratories, protecting operators from exposure to liquids and aerosols for a safer working environment. The system additionally features optional liquid level detection to prevent overfilling, and a filter to protect the vacuum source from contamination. Vacuum range: -300 to -600 mbar (adjustable) Pump flow rate: 8 l/min (air) Liquid aspiration rate: 17 ml/s (aspiration pipet) Noise emission: <50 dB(A) at 1 m Dimensions (HxWxD): 530 x 180 x 320 mm Weight: 3.4 kg

It is the ideal solution for laboratories and institutions requiring the highest precision. The cyli (more)ndrical mass standards are made from the highest quality materials, ensuring their stability and resistance to changes in environmental conditions. This makes them perfect for the calibration of precise measuring instruments. Product Features: Highest Class of Accuracy: Class E1 is the highest standard of accuracy, making these standards ideal for calibrating precision measuring instruments. Cylindrical Shape: The cylindrical shape of the standards ensures ease of handling and precise placement on weighing platforms. Wooden Packaging: The standards are delivered in an elegant wooden box, which ensures their safe storage and transport. Set Includes: 17 mass standards, 2 pairs of tweezers, 2 brushes and 1 pair of gloves. Applications E1 class standards are ideal for the calibration and verification of precise analytical and laboratory balances, indispensable in metrology laboratories, as well as in research and industrial institutions where maintaining the highest standards of accuracy is necessary. By choosing the E1 class mass standard set from RADWAG, you invest in reliability, precision, and durability, which translates to excellent quality in your laboratory work.

Horizontal laminar flow hood OPTIGEL 12 ADS LAMINAIRE Work in a sterile environment and Product Prot (more)ection - Complies with ISO Class 5 (ISO 14644 Standard) Useful dimensions (WxHxD): 1225 x 575/620 x 570 mm Overall dimensions (WxHxD): 1245 x 813 x 916 mm Flow rate (m3/h): 1000 Fan type: DF 280 ECM Absolute filter (on blowing): M14-612-250-A-P Prefilter: W0412202C Power supply: Mono 220 + T 16 A 50 Hz Power: 500 W Weight: Approximately 100 kg Lighting level 600 to 800 lux on the worktop Year of manufacture: 2022 Hour counter: 20000h Original filters