Watson Marlow SCIQ 323 Peristaltic Pump

This listing is for 1 of 2 Watson Marlow SCIQ 323 Peristaltic Pump. The unit is in full working con (more)dition and is ready for immidate realese. The Sci-Q 323 range is designed exclusively for scientific pumping needs, and brings a stunning level of performance and quality to the benchtop.   323S high-performance manual control variable speed pump • High-performance microprocessor controlled pumps • 323S can be extended with 313X extension pumpheads to five channels • Flow rates to 2000ml/min and 133:1 speed control ratio   323S speed adjusts in 1rpm steps from 3 to 400rpm. keypad lock prevents tampering or accidental changes, auto restart for mains failure recovery, switchable between 100-120V or 220-240V, MemoDose facility for accurate single shot dosing.   323S drives may also be fitted with 314 four roller pumpheads if lower pulsing is required, or with 313D2 or 314D2 pumpheads which accept 2.4mm wall thickness tubing for higher pressure operation or pumping more viscous fluids.   For low-flow pumping, up to ten channels, 323S drives may be fitted with 314MC (four-roller) microcassette pumpheads, which can be extended to ten channels by adding one 314MCX or 318MCX extension pumphead. This pump is fitted with one 314MC head and will be supplied with an additional spare 314MC as per images   Serial# H041702   Dims 27cm (D) x 22cm (W) x 12cm (H)

This listing is for 1 of 2 Watson Marlow 520S Peristaltic Pump. The unit is in full working conditi (more)on and is ready for immidate realese. Peristaltic pumps are the simplest possible pump, with no valves, seals or glands to clog or corrode. The fluid contacts only the bore of a tube, eliminating the risk of the pump contaminating the fluid, or the fluid contaminating the pump. Peristaltic pumps can operate dry without risk. Easy to install, simple to operate and inexpensive to maintain, peristaltic pumps are ideal for most fluids, including viscous, shear-sensitive, corrosive and abrasive fluids, and those containing suspended solids. Suitable for metering, dosing and dispensing applications.   520S drive offers manual control via a large-key membrane keypad: speed adjustment; run and stop; forward/reverse; "Max" key for rapid priming and purging.   Supply voltage/frequency: 100-120V/200-240V 50/60Hz Flow rates from 4 microliters/min up to 2.4 liter/min Precise 2,200:1 speed control range from 0.1 to 220 rpm in 0.1 rpm increments Large speed/flow display and easy to use tactile membrane keypad. Incorporates keypad lock Manual control and flow rate calibration MemoDose for accurate single shot dispensing

Gilson MiniPuls 3 peristaltic pump Technical characteristics Voltage: 220-240V, 50/60Hz Power: 45VA  (more)Speed: 0-48 revolutions 8 channels Standard flow rate: 0.3 µL/min – 30 mL/min at maximum pressure 0.5 MPa Pump head speed: adjustable 0 to 48 rpm with increments 0.01 rpm to 9.99 rpm and increments 0.1 rpm to 10 rpm Standard model pipe diameter: 0.25–4 mm (ID) External dimensions (L) x (D) x (H): 15 x 17.5 x 29.5 cm

Heidolph Outlet instrument*. 12 months warranty. *Heidolph Outlet instrument can be overstocked item (more), returns, demo instrument etc. They are checked by Heidolph and in a 100% functional condition. Profit from great savings thanks to slight optical defects. - Recommended for standard applications - Convex rollers do not squeeze or crush organic cell cultures - Pump head features ball bearings - Rollers made of stainless steel and polyamide - For tubes with a 1.6-mm wall thickness (wt) - Depending on drive and tubing, the flow rate ranges from 2.0 to 4,151 ml per minute

Heidolph Hei-FLOW Expert 120 Peristaltic Pump Package w/ Adaptor for Multi-Channel Pump Heads The pu (more)mp drive of the model 01 of the Hei-FLOW Expert series can be operated with either single-channel or multi-channel pump heads. The flow rates with single-channel pump heads are in the range of 0.38 — 813 ml/min; with multi-channel pump heads from 0.005 — 329 ml/min.By integrating an analog interface, it is possible to control all functions externally. In addition, an optional foot switch can be adapted to enable dosing by foot pressure. Hands thus remain free to perform other work, for example, to hold the tubing and the vessel.A speed of 5 — 120 rpm with a control accuracy of ±3.5% guarantees optimum process results. Features:- Increase your throughput by running up to 12 individual cassettes on one single pump drive and pump head system - Separate metering into multiple vessels with different feed rates in a single operation by using different tubing dimensions to adjust flow rate - Save time: tubing change is done in just seconds - In addition to standard pump heads which feature a 4-roller system you can choose 8-roller pump heads for low pulsation - Change your cassettes easily, even during operation – there are no restrictions - Cassette adjustments and changes are simple, just click in place - No additional purchase of a pump drive needed: upgrade your single-channel pump drive with just one adaptor for multi-channel use and pick the head/cassette configuration that matches your application needs Click Here to View Product Video INCLUDED: The Heidolph Hei-FLOW Expert 120 Peristaltic Pump Package w/ Adaptor for Multi-Channel Pump Heads includes: - Heidolph Expert 120 Peristaltic Pump - Adaptor for Multi-Channel Pump Heads - Power Cord - Operator's Guide - Full 3 Year Manufacturer's Warranty

Heidolph Hei-FLOW Expert 120 Peristaltic Pump The pump drive of the model 01 of the Hei-FLOW Expert  (more)series can be operated with either single-channel or multi-channel pump heads. The flow rates with single-channel pump heads are in the range of 0.38 — 813 ml/min; with multi-channel pump heads from 0.005 — 329 ml/min.By integrating an analog interface, it is possible to control all functions externally. In addition, an optional foot switch can be adapted to enable dosing by foot pressure. Hands thus remain free to perform other work, for example, to hold the tubing and the vessel. A speed of 5 — 120 rpm with a control accuracy of ±3.5% guarantees optimum process results. Click Here to View Product Video INCLUDED: The Heidolph Hei-FLOW Expert 120 Peristaltic Pump includes: - Power Cord - Operator's Guide - Full 3 Year Manufacturer's Warranty

MA X7.A moisture analyzers are hi-tech measuring instruments intended for quick determination of rel (more)ative moisture content, dry mass content and other parameters in samples of different substances. MA.X7.A series is equipped with innovative system: the drying chamber can be opened and closed automatically using button or proximity sensors. Such solution allows: Maintaining moisture analyzer clean – operator does not touch moisture analyzer’s housing. Removing any shocks caused by manual closing of the chamber – the chamber closes automatically and always with the same intensity. Achieving high repeatability of opening and closing the drying chamber. Enhancing drying process automation. Enhancing safety of operation by eliminating contact with hot components of drying chamber. Improving operation ergonomics. MA.X7.A series features user-friendly colour touchscreen. Free configuration of the control panel can be done by means of hotkeys, customizable information fields and programmable labels. Drying process can be carried out for any temperature and – thanks to databases – particular drying process may be set for a specific product. Highlights of X7 Series moisture analyzers: Automatic opening and closing of the drying chamber 7” capacitive colour touchpad Modern interface Uncomplicated, intuitive operation Programmable display Drying profiles (standard, mild, step, fast) GLP/GMP printouts-reports Repeatable and customized applications Work optimization due to the use of halogen lamps Capacity and temperature MA.X7.A maximum capacity ranges from 50g/0.1mg to 210g/0.1mg. Moisture content is measured with the 0.01% accuracy (0.001 % for samples bigger than 1.5g). The maximum drying temperature is 160˚C (there is an optional moisture analyzer with 250˚C maximum temperature). An additional element for moisture analyzers that improves their functionality is a water vapour permeability determination set used in tanning industry for determining hygienic properties of leather. Databases: Information system of X7 series moisture analyzers is based on 8 databases, allowing many users to operate product database comprising many samples. Collected measurements may be subjected to subsequent analysis. Collected data is registered in 8 databases: Products (up to 5000 products) Users (up to 100 users) Packaging (up to 100 packagings) Customers (up to 1000 customers) Drying programs (up to 200 drying programs) Drying process reports (up to 5000 drying process reports) Ambient conditions (up to 10000 records) Weighings (up to 50000 records) The results The results obtained using the moisture analyzer (the final result of the drying process): % M – the mass loss in %; displays the mass change recorded during the drying process, expressed as a percentage, % D – the dry mass obtained during the drying process, expressed as a percentage; the result is the portion of the sample that remains on the weighing pan after the moisture has evaporated, % R – the ratio of moisture content to dry mass, obtained during the drying process, expressed as a percentage; the result is the portion of the sample that evaporated during the drying process, g – the sample mass after drying. Interfaces USB interface ensures quick transfer and copying of any results of your work (measurements, reports, databases) to a computer or other moisture analyzer. Remote access to the moisture analyzer allows for online data management. Cooperation with E2R allows for external data management which in turn increases the efficiency and results to the maximum.

MA X2.A moisture analyzers are hi-tech measuring instruments intended for quick determination of rel (more)ative moisture content, dry mass content and other parameters in samples of different substances. MA.X2.A series is equipped with innovative system: the drying chamber can be opened and closed automatically using button or proximity sensors. Such solution allows: Maintaining moisture analyzer clean – operator does not touch moisture analyzer’s housing. Removing any shocks caused by manual closing of the chamber – the chamber closes automatically and always with the same intensity. Achieving high repeatability of opening and closing the drying chamber. Enhancing drying process automation. Enhancing safety of operation by eliminating contact with hot components of drying chamber. Improving operation ergonomics. MA.X2.A series features user-friendly colour touchscreen. Free configuration of the control panel can be done by means of hotkeys, customizable information fields and programmable labels. Drying process can be carried out for any temperature and – thanks to databases – particular drying process may be set for a specific product. Highlights of X2 Series moisture analyzers: Automatic opening and closing of the drying chamber 5” capacitive colour touchpad Modern interface Uncomplicated, intuitive operation Programmable display Drying profiles (standard, mild, step, fast) GLP/GMP printouts-reports Repeatable and customized applications Work optimization due to the use of halogen lamps Capacity and temperature MA.X2.A maximum capacity ranges from 50g/0.1mg to 210g/0.1mg. Moisture content is measured with the 0.01% accuracy (0.001 % for samples bigger than 1.5g). The maximum drying temperature is 160˚C (there is an optional moisture analyzer with 250˚C maximum temperature). An additional element for moisture analyzers that improves their functionality is a water vapour permeability determination set used in tanning industry for determining hygienic properties of leather. Databases: Information system of X2 series moisture analyzers is based on 8 databases, allowing many users to operate product database comprising many samples. Collected measurements may be subjected to subsequent analysis. Collected data is registered in 8 databases: Products (up to 5000 products) Users (up to 100 users) Packaging (up to 100 packagings) Customers (up to 1000 customers) Drying programs (up to 200 drying programs) Drying process reports (up to 5000 drying process reports) Ambient conditions (up to 10000 records) Weighings (up to 50000 records) The results The results obtained using the moisture analyzer (the final result of the drying process): % M – the mass loss in %; displays the mass change recorded during the drying process, expressed as a percentage, % D – the dry mass obtained during the drying process, expressed as a percentage; the result is the portion of the sample that remains on the weighing pan after the moisture has evaporated, % R – the ratio of moisture content to dry mass, obtained during the drying process, expressed as a percentage; the result is the portion of the sample that evaporated during the drying process, g – the sample mass after drying. Interfaces USB interface ensures quick transfer and copying of any results of your work (measurements, reports, databases) to a computer or other moisture analyzer. Remote access to the moisture analyzer allows for online data management. Cooperation with E2R allows for external data management which in turn increases the efficiency and results to the maximum.

Benchmark MiniMixer 3D Nutating Shaker The Benchmark MiniMixer 3D multi-functional shakers provides  (more)a 3-dimensional “nutating” motion for thorough, foam-free mixing in blood and centrifuge tubes, as well as in a variety of flat vessels. The MiniMixer comes standard with an autoclavable dimpled mat while optional flat mats are also available for mixing other vessel types. Stacking platforms can be purchased as accessories, effectively doubling the usable surface area of each model. Even the smallest single platform configuration has 24% more platform work surface than traditional nutating mixers. These mixers feature maintenance free, brushless motors capable of loads up to 2kg and are safe for use in cold rooms and incubators. INCLUDED: The Benchmark MiniMixer 3D Nutating Shaker includes: - 10 x 7.5 inch Dimpled Mat - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Benchmark BactiZapper Infrared MicroSterilizer The BactiZapper has an asbestos-free core element tha (more)t uses infrared heating to produce 815C (1500°F). It completely sterilizes in 5-7 seconds. The BactiZapper uses well-proven technology to provide instant sterilization of platinum inoculating loops, needles, glass tube/pipette mouths and various metal & borosilicate glass instruments used in quality control and research. It also has a lower temperature setting (500C) that can be used as a “standby” and extends usable life. The ceramic heating element is safely enclosed in a perforated stainless steel guard chamber, protecting users from accidental contact with the extreme temperatures of the core area. It is extremely compact, convenient, and can be used in anaerobic and aerobic chambers. INCLUDED: The Benchmark BactiZapper Infrared MicroSterilizer includes: - Power Cord - Operator's Guide - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW