Watson Marlow 530S Peristaltic Pump

This listing is for 1 of 2 Watson Marlow SCIQ 323 Peristaltic Pump. The unit is in full working con (more)dition and is ready for immidate realese. The Sci-Q 323 range is designed exclusively for scientific pumping needs, and brings a stunning level of performance and quality to the benchtop.   323S high-performance manual control variable speed pump • High-performance microprocessor controlled pumps • 323S can be extended with 313X extension pumpheads to five channels • Flow rates to 2000ml/min and 133:1 speed control ratio   323S speed adjusts in 1rpm steps from 3 to 400rpm. keypad lock prevents tampering or accidental changes, auto restart for mains failure recovery, switchable between 100-120V or 220-240V, MemoDose facility for accurate single shot dosing.   323S drives may also be fitted with 314 four roller pumpheads if lower pulsing is required, or with 313D2 or 314D2 pumpheads which accept 2.4mm wall thickness tubing for higher pressure operation or pumping more viscous fluids.   For low-flow pumping, up to ten channels, 323S drives may be fitted with 314MC (four-roller) microcassette pumpheads, which can be extended to ten channels by adding one 314MCX or 318MCX extension pumphead. This pump is fitted with one 314MC head and will be supplied with an additional spare 314MC as per images   Serial# H041702   Dims 27cm (D) x 22cm (W) x 12cm (H)

220-240V, 50-60 Hz, 16W

The Watson Marlow 405 Pump provides users with digital control over a two-channel precision pump. Th (more)is high flow laboratory pump has a speed range up to 200 rpm with a flow rate up to 370ml/min per channel. This microprocessor controlled, dual channel peristaltic pump is easy to control from the upfront digital keypad, allowing users to start, stop, reverse direction, control speed level, and initiate rapid priming. This digital lab pump is built for use with 1.6 mm tubing in sizes 12, 13, 14, & 16 (0.5 – 64.8 mm bore) and spring-loaded track to maximize tube life and flow precision against pressures up to 2 bar. The pump comes with pumphead designed with twin four roller rotors, spring loaded track, and adjustable occlusion lever allowing two individual channels of flow.

Pharmacia Biotech FPLC System This was removed from a university lab where it was surplus to require (more)ments. The system has been powered up but not tested further. Everything is in reasonable to poor cosmetic condition. All the units plugged into a power strip that supports EU plugs. Included are; 2 x Connectivity Monitor, 004763/System No. 003763, 004518/System No. 0035181 x Pump P-500, 0175171 x Liquid Chromatography Controller LCC-500 Plus, 3315431 x UV-M II, 0045862 x MotorValve MV-71 x 10200 PERSPEX Peristaltic Pump, 5024

This Watson Marlow 205S Peristaltic Pump was removed from a university lab where it was surplus to r (more)equirements. The unit powers on and is in good cosmetic condition with minor marks from use. All buttons are responsive to the unit.

Buchi Mini Spray Dryer B-290 This item was removed from a university where it was surplus to require (more)ment. It is in good cosmetic condition and powers on. The display isn't clear, but it looks to be showing "error 04". The display then stopped showing any numbers or any sign of power. the ON/OFF switch still showed power. All buttons did not appear to be responsive. The Peristaltic pump did not move or appear to show any sign of power. The pump at the back of the unit did not show signs of power or make a noise either. Trolley included. It is sold for spares/repairs.

Stirring quantity max.: 20 l Speed range: 0/50 – 1700 rpm Stirring bar length max.: 80 mm Heating te (more)mperature range: room temp. – 340 °C Speed control: stepless Connection for ext. temperature sensor: PT1000 Control accuracy with sensor: 1 ±K Plate dimensions: Ø 135 mm Dimensions (WxHxD): 160 x 95 x 270 mm Weight: 2.5 kg

This Skalar San+ Segmented Flow Wet Chemistry Autoanalyser System was removed from a university lab  (more)where it was surplus to requirements. Everything powers up but has not been tested as a system as there is no PC or software. Everything is packed in black flight cases. The system consists of: Skalar San+ Segmented Flow AutoanalyserType - 4000 Skalar SamplerType - 1000 Skalar InterfaceType - 8503 Skalar Temp Control UnitType - 5540 Skalar ReactorType 5521 HP Deskjet 940C Printer There is one box that contains the following Skalen parts/tubing (listed by part number)2 x 262009031 x Astro D-27607 Langen1 x Cogwheel - 223000121 x Spring 6 Pack - 223003174 x Cogwheels for Motor - 223000451 x Rollercage for SA2100 Pump - 223003121 x Motor for SA4000 - 90020766Tubing (Mix of sealed/opened packs):-1 x 51551 x 51501 x 31421 x 31502 x 51411 x 51304 x 10602 x 30242 x 30256 x 30261 x 30273 x 30287 x 30294 x 30304 x 30315 x 30324 x 30331 x 30344 x 30351 x 3036 There another box that contains the following Skalen parts (listed by part number)1 x Start up kit 57038 x 53231 x 10111 x 53131 x 10111 x 52611 x 52161 x 52601 x 92212 x 53255 x 53246 x 52028 x 5210

This was removed from a lab where it was surplus to requirements. The unit powers up and draws sucti (more)on. It is in good cosmetic condition but has some minor marks from use. Included with it is; 1x Glass Jar w/ Lid1700 ccm

Coherent Sapphire 488-200 CDRH Laser with CDRH HP Controller This was removed from a university lab  (more)where it was surplus to requirements. Both units power up and the laser beam is working. It was tested with a cable from another unit. It is not included. It is in good cosmetic condition with only minor marks from use. Controller:-Model - Sapphire CDRH HPPart no. 1142958 REV AB Laser head:-Model - Sapphire 488-200 CDRH

Precision in PRO version The CY10 series precision balance is designed for fast, accurate and repeat (more)able weight determination. It comes with an advanced PUE CY10 terminal, and that means working comfort with a 10-inch high-resolution display with a smooth and intuitive interface. Software for special tasks Thanks to the terminal advanced software, the CY10 series precision balance: Cooperates with up to 2 weighing platforms Continuously updates all statistical data after the next measurement is entered into the balance’s memory – either globally (regardless of the weighed commodity) or separately for each weighed commodity selected from the database Has a Tare mode expanded to include End-product issue mode capability Works with RFID tags* (accessing personal data as well as marking specific goods or recipe ingredients in the database). Precision balance and labelling scale in one device If you need a labeling scale, the CY10 is the perfect solution. With a terminal that: Cooperates with the computer program Label Editor R02 Is compatible with ZEBRA label printers Supports single labels, bulk labels and bulk from bulk labels Allows import/ export of label designs using a pendrive Enables you to assign labels to goods or customers and print a global label The CY10 series precision balance can operate as a labeling scale. Light or dark? Which color theme will you set on your CY10 balance? Both are user-friendly and clear, but we are curious which one you like more. Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13,56 MHz

Eppendorf 4 x 10ml Vacutainer Adapters, Cat. # 022639269 New in box Eppendorf 4 x 10ml Vacutainer Ad (more)apters, Cat. # 022639269 for the A-4-38 rotor. This is a 2 piece set, and the adapters are new in the packaging. The Eppendorf 4 x 10ml Vacutainer Adapters, Cat. # 022637269 are used in Eppendorf 5702/R Centrifuges. INCLUDED: The Eppendorf 4 x 10ml Vacutainer Adapters, Cat. # 022639269 includes: - Full 6 Month Parts and Labor Warranty