Circulating water bath / Thermostat JULABO P/1 + 13 litre tank

Water bath from 25°C to 100°C for the laboratory The ring baths for columns, Erlenmeyer flasks or be (more)akers are suitable for continuous operation, even unattended, thanks to the standard level and lack of water monitoring. LAUDA Hydro ring water baths are available in five models, all featuring a removable perforated lid with a set of heat-resistant plastic rings. - Operations in a temperature range from 25 to 100°C. - Models H 11 V, H 19 V have been specially designed for safe use in fume cupboards. - The housings are made of stainless steel to allow their use even with chemically aggressive fluids. - Temperature regulation by knob with graduated scale - Lid with set of rings for opening the modular tank - Water level and lack control, for continuous unattended operations - The support rods (length 600 mm, diameter 12 mm), made of stainless steel, are included as standard - Hydro is protected against dry running by an electro-mechanical valve. In case of low water, the heating is stopped In the photo, simple control panel, with knob, graduated scale, warning light and safety valve. Ring opening, to adapt to different types of glassware. Standard water level regulator for continuous operation, even unattended. Safety system in case of water shortage LAUDA evaporization baths are protected against dry running by a cut-off device for lack of water (thermostatic overvoltage). The nut located on the control panel will be used to disarm the security system. Water level regulator as standard Thanks to this accessory, the loss of water inside the instrument (through evaporation) is compensated and the water level is kept constant. Furthermore, it allows use at temperatures below ambient temperatures, with a minimum of approx. 3°C above tap water temperature.

Histological water bath from 25°C to 80°C for the laboratory This water bath model is used in histol (more)ogical, chemical, clinical and bacteriological laboratories for stretching and drying tissue samples. The exact temperature control of the LAUDA Hydro H 2 P water bath ensures clear visibility of the sample and gentle drying even on the heated edge. The instrument operates in a temperature range from 25 to 80°C with a constant temperature of ± 0.5 K. The body of the bath is made of black anodized aluminum. The low height of the bowl allows comfortable and safe work. - Temperature adjustment by knob with temperature scale - Temperature display by means of a reference thermometer on the edge of the pool - Tank interior in black anodized aluminum If you want to know more about water baths in histopathology and new histotechnologies in general, we recommend the HistoTube YouTube channel. Accessories Lid, to cover the bath interior, made of black anodised aluminium, with ball handle.

Water bath from 25°C to 100°C for the laboratory The water baths of the LAUDA Hydro series are the i (more)deal tools for any laboratory application, whether biological, medical or biochemical and guarantee a homogeneous temperature distribution without overheating problems. High quality stainless steel and thoughtful design, provide the ideal depth and opening for any application with bathroom volumes from 4 to 41 liters. All water baths offer a temperature range up to 100°C, with a temperature stability of ±0.1K, so that applications even in the boiling range are possible. A TFT color display ensures intuitive operation with temperature display in °C and °F. The 'A' models (Agitation: H 8 A; H 16 A) have a magnetic stir bar liquid circulation system as standard, to improve temperature uniformity. Application examples - Preparation of cellular, biological or medical samples - Microbiological test incubation - Thawing of the samples - Conducting chemical reactions Notable features - Three timer functions for the user - Electric resistance inside the tank - Direct temperature control for fast and precise heating - Visual and acoustic alarm in case of lack of water, low / high temperature and sensor break - Digital and electromechanical safety system - Lid designed to prevent condensation from dripping onto samples - Exhaust valve on all models Standard equipment - Lid and drain tap in heat-insulating double-walled stainless steel Accessories available Water level regulator. Highest quality materials: tank interior, lid, sieve and heating element made of stainless steel. Heat insulating lid in stainless steel, double walled with internal curvature to guide the condensate. Dump valve on all Hydro Lauda models. Simple control panel with large TFT display with extensive information; change settings and navigate quickly and easily. Optical and acoustic alarm for low water level and over/under temperature as well as sensor breakage/short circuit. Optimized space, safety and comfort of use. Connection for water level regulator (available as accessory). Water circulation The circulation system guarantees optimal temperature distribution throughout the tub. It is managed by a magnetic electric motor which transmits the rotation to a PTFE-coated stirrer in the tank. The agitator draws the water towards the center and then distributes it to the rest of the tank. The water circulation is activated via the main switch. Recommended accessories - Water level regulator. The water regulator located on the back of the water bath is used to maintain constant the set water level during water loss due to evaporation. Furthermore, it allows use at temperatures below ambient temperatures, with a minimum of approx. 3°C above tap water temperature.

Capacity: 17 L Max temperature: 100°C Max flow rate: 17 L/min Max pump pressure: 300 mbar Dimensions (more) (DxWxH): 457 x 381 x 456 mm Weight: 13.7 kg

Covaris S2 Focused Ultrasonicator with Grant LTC1 Water Bath This was removed from a university lab (more) where it was surplus to requirements. Included are; 1 x Covaris S2 Focused UltrasonicatorModel S2Ser No. 541The unit powers on and is in good cosmetic condition. The motor can be heard almost immediately after powering on the unit. We were unable to test it further.1x Grant LTC1Model R2The unit powers on and is in good cosmetic condition.It has been tested with a digital thermometer (not included) and is in good working order.

Julabo SW23 Shaking Water Bath 115V/60Hz Working Temperature Range 20°C to 99°C Shaking Speed Range (more) 20 to 200 RPM Volume 20L Features - Microprocessor technology with PID temperature control - Bright Multi-Display (LED) - Seamless, splash-proof keypad - Splash-proof mains switch - Electronic timer for setting the running time (0:01 to 9:59 h:min) - On-line communication via built-in RS232 interface - Early warning system with high and low temperature limits - Drain screw for conveniently emptying the bath - Dry-running protection / safety temperature fixed at 105 °C - Wide range of accessories including lift-up Makrolon bath cover available - EasyTemp control software is available free of charge - Removable shaking carriage - Shaking frequency adjustable from 20 to 200 rpm - Shaking frequency indicated on Multi-Display (LED) - Shaking stroke 15 mm - With integrated circulation pump The JULABO SW shaking water baths provide for unsupervised sample incubation. Stainless steel construction with an operating range from +20°C to +99.9°C. User-friendly operation via keypad with bright LED display. Electronic timer from 1 min to 9h 59min. Integrated RS232 interface for integration to PC software for control and data logging. Early low water level warning system. Early warning system with high and low temperature limits ensures that samples maintain the proper temperature. A removable shaking carriage for easy sample removal. A wide range of accessories, including bath covers, are available. Shaking frequency adjustable from 20 to 200 rpm. Shaking stroke = 15 mm. SW22 unit with ± 0.2°C stability. SW23 incorporates a water circulation pump for a stability of ± 0.02°C. INCLUDED: The Julabo SW23 Shaking Water Bath 115V/60Hz includes: - Removable Shaking Carriage - Integrated Circulation Pump - Power Cord - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

This listing is for a Thermo Scientific Orion Star A211 Bench Top pH Meter. The unit is in full wor (more)king condition and is ready for immediate release. The Orion Star A211 is designed for accurate and convenient pH measurement, making it essential for various laboratory applications. Key Features: Versatile Measurements: Capable of measuring pH, mV, ORP, and temperature, catering to a wide range of analytical needs. Advanced Calibration: Offers up to 5-point pH calibration with automatic recognition for common buffer standards (USA/NIST and DIN), ensuring high accuracy. Data Logging: Can log up to 2000 data point sets with time and date stamps, facilitating easy tracking of measurements for future reference. Data Transfer Capabilities: Easily transfer calibration and data logs via USB or RS232 to a printer or computer, streamlining data management and reporting. User-Friendly Design: Includes an electrode stand for convenient placement and storage of sensors, along with a comprehensive keypad featuring menu-specific function keys for intuitive operation. Multilingual Support: Supports multiple languages (English, Spanish, French, Italian, German, and Chinese), making it accessible for diverse users. Backlit Graphic LCD Display: Displays critical information, including pH/mV/RmV, temperature, electrode status, time, date, sample ID, user ID, and calibration points, ensuring that users have real-time access to vital data. Specifications: pH Range: -2 to 20 mV Range: ±2000.0 mV Temperature Range: -5°C to 105°C Resolution: pH: 0.001, 0.01, 0.1 mV: 0.1 Temperature: 0.1°C Accuracy: pH: ±0.002 mV: ±0.2 mV or ±0.05% of reading (whichever is greater) Calibration Points: 1 to 5 Data Management: Ability to transfer single, range, or all data points to a printer or computer.

F1 Mass Standard - monoblock weights without adjustment chamber. Nominal value - 2 g.

Do you need a moisture analyzer that not only determines moisture or dry matter content with impress (more)ive accuracy, but also performs a digital audit, responds to your voice commands and sends you light messages? If so, learn about the functionality of the ELLIPSIS series of moisture analyzers: It Dries in 4 Ways The MA 5Y Moisture Analyzer offers you four drying profiles: standard, mild, fast and step. The standard profile is the usually used drying profile. It allows the most accurate determination of moisture content. The mild profile is designed for drying substances that are sensitive to the rapid heat released by the filaments, which heat full power at the initial stage of the process. An example of such a substance is leather. You will use the fast profile for samples with significant moisture content – of the order of even several tens of percent. The step profile will be ideal for drying substances that contain more than 15 percent moisture. Within this profile you can define any three temperatures. You will choose the values of temperature and duration of heating experimentally. What Drying Temperature Should I Set? The drying temperature determines the duration of the process. Its value depends on the type of material. If the temperature is too low, it will under-dry the sample and, consequently, unnecessarily increase the measurement time, while if it is too high, it will cause a burning effect on the material. The drying temperature for the traditional (oven) method is determined by industry or factory standards. If there are no standards, you will select the temperature experimentally. The maximum drying temperature on the MA 5Y Moisture Analyzer is 160°C. How Do I Finish the Drying? In 4 Ways The MA 5Y Moisture Analyzer has four finish modes: automatic, manual, time-defined and user-defined. Automatic mode You define the moisture loss limit value in 60 seconds. When the moisture analyzer reaches the set criterion, the measurement will automatically end. Manual mode You terminate the measurement yourself by pressing the STOP button. Time-defined mode The measurement ends after the set time has elapsed regardless of the result. You have up to 99 hours 59 minutes to manage! User-defined mode When you remove all volatiles from a sample, by definition, its mass should be constant. During drying, the dry mass of the sample is defined by a condition: if the mass of the sample is stable within 1 mg during the observation time (Auto 1-5), we consider that all volatile components have been removed from its structure. Digital Weighing Auditor Ensures that your moisture analyzer is ready for use. What is more, it informs about the need for a moisture analyzer inspection or a periodic audit of the moisture analyzer’s accuracy and sensitivity. 10-Inch Display Bigger screen – 10’’ – means more information in one place. On the new ELLIPSIS terminal, you will see up to 3 screens, widgets, graphs, statuses, notes, handy measurement history. Uncompromising User Verification For the first time ever, the moisture analyzer will verify the user using a password, RFID card, fingerprint reader, facial recognition mechanism, or any combination of these. Ambient Light – an Innovative Way for the Moisture Analyzer to Communicate With the User The light colour will tell you about status, process results, procedures, or alerts. Hotspot Use the moisture analyzer on any device connected to it. This can be a smartphone, tablet, or computer. RFID ELLIPSIS works with RFID tags* that can be used to tag your products or formulation ingredients in the database. They can also be used to identify a user. Live Note – Note Down Your Conclusions It’s the first time you can add a voice memo to a measurement series or procedure report. If you prefer to write it down, ELLIPSIS allows you to add a text note. Handy Library This is where a series of recent measurements or a report ready for digital signature, according to 21 CFR Part 11, can be found. Widgets Prepared to display what you need most at any given moment. 21 CFR Part 11 Do you work in the pharmaceutical industry? Do you need a digital signature? We are offering the moisture analyzer which as a standalone fully meets the requirements of 21 CFR Part 11/ EU GMP Annex 11. Full data security Electronic signatures Validations Electronic records Audit trails Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13.56 MHz

Do you need a moisture analyzer that not only determines moisture or dry matter content with impress (more)ive accuracy, but also performs a digital audit, responds to your voice commands and sends you light messages? If so, learn about the functionality of the ELLIPSIS series of moisture analyzers: It Dries in 4 Ways The MA 5Y.IC Moisture Analyzer offers you four drying profiles: standard, mild, fast and step. The standard profile is the usually used drying profile. It allows the most accurate determination of moisture content. The mild profile is designed for drying substances that are sensitive to the rapid heat released by the filaments, which heat full power at the initial stage of the process. An example of such a substance is leather. You will use the fast profile for samples with significant moisture content – of the order of even several tens of percent. The step profile will be ideal for drying substances that contain more than 15 percent moisture. Within this profile you can define any three temperatures. You will choose the values of temperature and duration of heating experimentally. What Drying Temperature Should I Set? The drying temperature determines the duration of the process. Its value depends on the type of material. If the temperature is too low, it will under-dry the sample and, consequently, unnecessarily increase the measurement time, while if it is too high, it will cause a burning effect on the material. The drying temperature for the traditional (oven) method is determined by industry or factory standards. If there are no standards, you will select the temperature experimentally. The maximum drying temperature on the MA 5Y.IC Moisture Analyzer is 160°C. How Do I Finish the Drying? In 4 Ways The MA 5Y.IC Moisture Analyzer has four finish modes: automatic, manual, time-defined and user-defined. Automatic mode You define the moisture loss limit value in 60 seconds. When the moisture analyzer reaches the set criterion, the measurement will automatically end. Manual mode You terminate the measurement yourself by pressing the STOP button. Time-defined mode The measurement ends after the set time has elapsed regardless of the result. You have up to 99 hours 59 minutes to manage! User-defined mode When you remove all volatiles from a sample, by definition, its mass should be constant. During drying, the dry mass of the sample is defined by a condition: if the mass of the sample is stable within 1 mg during the observation time (Auto 1-5), we consider that all volatile components have been removed from its structure. Digital Weighing Auditor Ensures that your moisture analyzer is ready for use. What is more, it informs about the need for a moisture analyzer inspection or a periodic audit of the moisture analyzer’s accuracy and sensitivity. 10-Inch Display Bigger screen – 10’’ – means more information in one place. On the new ELLIPSIS terminal, you will see up to 3 screens, widgets, graphs, statuses, notes, handy measurement history. Uncompromising User Verification For the first time ever, the moisture analyzer will verify the user using a password, RFID card, fingerprint reader, facial recognition mechanism, or any combination of these. Ambient Light – an Innovative Way for the Moisture Analyzer to Communicate With the User The light colour will tell you about status, process results, procedures, or alerts. Hotspot Use the moisture analyzer on any device connected to it. This can be a smartphone, tablet, or computer. RFID ELLIPSIS works with RFID tags* that can be used to tag your products or formulation ingredients in the database. They can also be used to identify a user. Live Note – Note Down Your Conclusions It’s the first time you can add a voice memo to a measurement series or procedure report. If you prefer to write it down, ELLIPSIS allows you to add a text note. Handy Library This is where a series of recent measurements or a report ready for digital signature, according to 21 CFR Part 11, can be found. Widgets Prepared to display what you need most at any given moment. 21 CFR Part 11 Do you work in the pharmaceutical industry? Do you need a digital signature? We are offering the moisture analyzer which as a standalone fully meets the requirements of 21 CFR Part 11/ EU GMP Annex 11. Full data security Electronic signatures Validations Electronic records Audit trails Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13.56 MHz