Mixing chamber

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

FURTHER DETAILS TO FOLLOW

Programmable flow rate: 0.00 to 5.00 mL/min, 0.01 mL/min increments Maximum operating pressure: 401  (more)bar Pressure ripple: <2% at 0.5mL/min Flow precision: 2 seconds SD Flow accuracy: 2% of setting Gradient accuracy: <1% between 10 to 90% Gradient precisison: <0.5% RSD between 10 to 90% Gradient delay volume: <60 µL (without mixer), <200 µL (with one 50 µL mixer) Inline degasser channels: 2 Dimensions (HxDxW): 430 x 610 x 305 mm Weight: 27.2 kg

This Shimadzu LC10-AS Liquid Chromatograph System was removed from a university lab where it was sur (more)plus to requirements. The unit powers up and is in good cosmetic condition with minor marks from use. It has not been tested further. It is supplied with a Shimadzu Syringe Unit .XL. We were unable to power this as it requires a 20-pin connecter.

This was removed from a university lab where it was surplus to requirements. The lab informed us tha (more)t it was in use until December 2022 and was fully serviced by Waters up to Feb 2023. All modules are in excellent cosmetic condition with only minor marks from use. Included are; 1 x Waters Sampler ManagerPart Number: 186016007S/N: J10NPS 788M The unit powers up but we were unable to test it further at our facility. This unit does include 2x part number 418000179 vile trays.&nbsp; 1 x Waters Binary Solvent ManagerPart Number: 186016002S/N: H10NPB 923NThe unit powers up, the flow light flashes red, green, and then turns off. We were unable to test it further at our facility. 1 x Waters Auxiliary Solvent ManagerPart Number: 186016021S/N: H10NPA 505NThe unit powers up but the flow light does the same as the binary manager. We were unable to test it further at our facility. There is also a network switch on the top of the stack. It is untested. It comes with 5x sealed bagged "nano inlet filter 5 micron", part number: 289002172 with dates on the bags ranging from 2011 to 2020. A set of bagged tubes that are labelled as "solvent aux".

Agilent 1100 Series HPLC System consisting of: 1100 Series Degasser G1379A S / N: JP40716471. Binary (more) Pump 1100 Series G1312A FW: A.07.01 S / N: DE43616890. Automated injector Series 1000 G1313A FW: A.07.02 S / N: DE23920959. Thermostated column compartment G1316A 1100 Series FW: A.07.02 S / N: DE43643595. 1100 Series UV Detector G1314A with 10mm cell and G1369A LAN card FW: A.07.02 S / N: JP24020131. Windows 7 PC with Chemstation B.04.03-SP1 Agilent 1100 Series HPLCs are considered the most popular HPLCs in the world. They are robust, durable and versatile systems. Our instruments are restored according to the manufacturer's specifications to provide the best performance. They have a one year warranty. The 1100 HPLC series supports efficient pump action as well as advanced data analysis and diagnostic software. The system is easy to use and has a low cost. Looking for a more personalized product? All of our Agilent HPLC systems can be configured to your specific requirements.

Vertex Velp digital thermoregulator The instrument can be combined with the most common heating magn (more)etic stirrers and is supplied ready for use, complete with temperature probe and power cable for direct connection to AREX, AREC.X, AREX-6 heating magnetic stirrers. Thanks to the PW 10 branch element, VTF can be used with all types of heating devices such as water and oil baths, hot plates, thermometers, etc. Temperature Accuracy The VTF thermoregulator can be used in many applications where precision, reliability and flexibility of use are required, as it is equipped with Fuzzy Logic, which allows the thermoregulation to be automatically adapted to different situations, such as power, load and heat loss. The highly sensitive probe offers state-of-the-art temperature control performance, with an accuracy of ± 0.5 ° C Exclusive Fixing System VTF is equipped with an exclusive and innovative integrated fixing system that facilitates the positioning of the Pt100 probe inside the most common beakers. The two lateral clamps allow the height adjustment of the VTF, while the friction system ensures its movement on the horizontal plane. No system will be as comfortable! - Integrated Digital Timer Another unique feature of the VTF is the integrated timer. It is in fact possible to select up to a maximum time of 24 hours and 59 minutes, while at the end of the countdown the instrument will automatically switch off the thermoregulation. The timer mode can be recognized by the alternating flashing of the 2 arrows on the left side of the display. - Technical features: Structure: technopolymer Fixing on rods: from Ø 10 to 13 mm Pt 100 stainless steel probe: length 250 mm and Ø 3 mm Display: LCD Degree of protection CEI EN 60529: IP 54 Power supply: 12 Vdc Weight: 0.3 Kg Dimensions (LxHxP): 75x145x120 mm Adjustment range: -10 ... +300°C Accuracy: ± 0.5°C Resolution: 0.2°C Timed operation: from 0:00 to 24:59 (h: min) Remaining time display: possible Display of maximum temperature reached: possible Display visualization and automatic switching off of the heating plate in case of: - Probe shorted - Probe interrupted

Lot of Cole Parmer MasterFlex Perstaltic Pump Heads These were removed from a university lab where t (more)hey were surplus to requirements. Included are; 2 x Masterflex Cole Parmer Pump Drives Mod Nos. 7544-06Speed 6rpm The units power on and are in good cosmetic condition with marks and stains.1x Pump drive has what looks like a terminal block wire connector. We attached a plug for testing but later removed it. Pump Drive Dims:L27cm x W10cm x H11cm Pump-Head Dims:L6cm x W7.5cm x H8cm Masterflex Cole Parmer Pump Heads:Part Nos. 3,358,609 - all have the same Part No. 2x Model 7014-52The units are in good cosmetic condition.There are some surface stains on all of the unit's ball bearings from general use. The ballbearing mechanism was tested by hand the action felt smooth. 2x Model 7024-20The units are in good cosmetic condition. The ballbearing mechanism was tested by hand the action felt smooth. 2x 7013-20The unit is in good cosmetic condition.The ballbearing mechanism was tested by hand the action felt it had some resistance. One of the fluid dispersing mechanisms stuck inside the housing of one of these pump heads.

Buchi K-350 Distillation Unit Lab This item was removed from a university lab where it was surplus t (more)o requirements. It is n good cosmetic condition and powers on, we are unable to test it further at our facility.

Picarro Cavity Ringdown Spectrometer L1102-i Isotopic H2O System This system was removed from a univ (more)ersity where it was surplus to requirement. It is in very good cosmetic condition with all units powered on, we are unable to test the system further at our facility. This system comprises the following: - Picarro Control PC unit ESP-100 Serial No. 274-CPVU-HBQ58Running Windows XP ProfessionalWith Picarro Software installed - Picarro Cavity Ringdown Spectrometer L1102-i ISOTOPIC H2O Serial No. 278-HBDS-0SF - Picarro Vaporisation Module ISOTOPIC A0211 Serial No. VAP073r236

Maximum temperature: 70°C Warm-up time (air flap closed at 25°C): to 37°C; 35 min, to 50°C; 35 min,  (more)to 70°C; 45 min Recovery time (door open for 30 sec): 2 min Air changes per hour (at set temperature with flap open): 5 Spatial temperature variation (air flap closed): at 37°C; ±1.1°C, at 50°C; ±1.6°C, at 70°C: ±2.5°C Temperature fluctuation: ≤0.5°C Maximum load: 50 kg Maximum shelf load: 10 kg Volume: 107 L Internal dimensions (DxWxH): 370 x 554 x 524 mm Dimensions (DxWxH): 610 x 895 x 696 mm Weight: 69 kg

The HX5.EX scale is a modern weighing instrument assuring fast and reliable measurement in hazardous (more) areas classified as zones 1/21 and 2/22. To ensure precision and excellent measurement repeatability, high quality electronic components are used. The weighing platforms offered in wide range of dimensions and maximum capacities, this combined with excellent metrological parameters enables easy selection of an instrument that meets the most demanding requirements. Standard version of the scale is equipped with 2 serial, intrinsically safe RS232 communication interfaces, and with one RS485 interface. They facilitate cooperation with equipment intended for operation in hazardous areas. Possibility to add digital inputs/outputs extends the range of instruments compatible with the indicator by automatic elements compliant with ATEX directive. More demanding customers can use the IM01.EX module, installed in the safe area, which extends the available connectors by Ethernet, USB, 4-20mA/0- 10V analog outputs, Profibus DP and additional digital inputs/outputs. This enables cooperation with external devices: barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. Scale operation requires use of a dedicated PM01.EX power supply, which is not a standard scale component. To operate the scale, order a selected type of the dedicated intrinsically safe power supply. Power supply types: PM01.EX-1 - power supply for operation in ATEX area. Used when it is required to connect the power supply to voltage source placed in hazardous area. PM01.EX-2 - power supply for operation outside ATEX area. Used when power supply connection to voltage source is carried out outside hazardous area. Complex software enables carrying out many tasks connected with mass measurement, e.g. parts counting, checkweighing and statistics. The scales feature user-friendly graphic interface, which can be customized using widgets. This and the large colour display of high resolution guarantee easy and clear transmission of data on current process. Colour bar graph significantly influences performance by signalling whether the weighing result is within declared thresholds or not.