Hewlett Packard 5890 Series II Gas Chromatograph Lab

This Agilent 6890N Network GC System w/ 5973 Network MSD was removed from a university lab where it  (more)was surplus to requirements. All units connect and power on, we are unable to test further at our facility. The cosmetic condition of all items is very good. Included are; 1x Agilent Technologies Gas ChromatographModel 6890N (G1530N)Version N.05.04 1x Gerstel MultiPurpose Sampler MPS2LModel MXY 06-01BSer no. 160791 1x Gerstel MultiPurpose Sampler Controller:Model MB01-00AFirmware 2.4.0 1x CTC Analytics Power Supply:Part no. MN 01-00 1x Unbranded double-sided Sampler Block:98x 1.5ml wells / 78x 0.5ml wells  1x Agilent Technologies 5973 Inert Mass Selective DetectorModel G2579A Inside the unit: 1x BOC Edwards Turbopump:G2589A -80062 Agilent Cables: 1x AMP 'Remote cable 9 pin MALE and FEMALE to 9 pin MalePart no. G1530-61200 1x AMP Remote to Interface 3pin to 4pin MALE to MALE Cable 1x HI VAC 3 pin DIN to IEC Cable:Part no. G1099-60435From 5973 MSD to Edwards BOC Turbo Pump 1x RS3M-2000 3 pin DIN to 3 pin MALE to MALE Cable:From CTC Analytics Power Supply to Multi Sampler

Interscience GC 8000 TOP

Reason for return - Investigate faults and re-list accordingly: - We received the item with a cracke (more)d glass piece to the photoionization detector. We replaced it with a piece that was provided. - We piped the system with N2 carrier gas and gas lines carrying product to the inlet of the GC. We turned on the switch to the Photoionization detector, under high sensitivity, and can visibly see it turn on. The source is aligned. The detector is aligned.  - We programmed the event on the software to turn the valve of the 10-way valve accordingly to enable the carrier gas to bring the product through the GC. - We introduced acetone via the sample loop (inlet gas) - we saw no peaks. We introduced acetone via injection - we saw no peaks.  - I leaked checked the piping including within the detector - no issues. I checked the point of outlets to make sure flow is continuous too - no issues. - The mechanism of the valve turning - it made a cranky sound, and I am not convinced it is turning the valve.  - There may be two issues. I had figured it was the valve so I tried injecting acetone directly into the line, but we could not see any peak of acetone. (Issues with the detector?) I am not sure if the valve's squeaking/cranky sound implies it is turning but there might be an issue here too. This SRI 8610C GC Gas Chromatograph System was removed from a university lab where it was surplus to requirements. The unit powers up but we were unable to test it further at our facility. The lab did confirm however, that is in good working order. It is in very good cosmetic condition with only very minor marks from use.

This Perkin Elmer GC Gas Chromatograph Clarus 480 was removed from a university lab where it was sur (more)plus to requirements. It is in reasonably good cosmetic condition and powers up. The original ECD detector has been removed, leaving mains cables exposed, therefore, this item is listed as Spares/Repair. Part number- N664948ESerial number- 480S13030901

HP 6890 5973 Series G1999A GC-MS Gas Chromatograph Mass Spectrometer System This was removed from a  (more)university lab where it was surplus to requirements. The lab confirmed that it is in good working order. At our facility we have connected the system together and powered it up, but not tested further. It is in good cosmetic condition with minor marks. Included are; HP ALS ready G1530ASerial No. US00028126 HP 5973 Mass Selective DetectorG1999ASerial No.US91430461 HP 59864B Ionisation Gauge ControllerSerial No. US60103518

Perkin Elmer Clarus 500 GC-MS Gas Chromatograph Mass Spectrometer System Lab This system was removed (more) from a university lab where it was surplus to requirements. The system has been professionally serviced and is in good working order. It is in excellent cosmetic condition with minor marks. The full-service report is available on request.

VWR OPTIKA B-292PLi Binocular LED Microscope Lab This item was removed from a university where it wa (more)s surplus to requirement. It is in good cosmetic condition and powers on, we are unable to test it further at our facility. This item includes the following: Objectives- IOS N-PLAN 4x/0.10IOS N-PLAN 10x/0.25IOS N-PLAN 40x/0.65IOS N-PLAN 100x/1.25 Eyepieces - 2 x EW10x/20 6v Dc Power Supply Included with Item.

VACUUBRAND VACUU-Select, VACUU-VIEW, VSP 3000, and KF DN 25 Package for Fine Vacuum Control Upper Me (more)asuring Limit 825 torr Lower Measuring Limit 1 x 10-3 torr Accuracy +/- 15% of indicated value in the range 0.01-5 mbar/hPa/torr Features - Complete package for vacuum control of all fine vacuum applications in chemical labs, with continuous control range from atmosphere to fine vacuum (10-3 mbar) - Metal components made of stainless steel for better chemical resistance - Graphic user interface for simple operation - Predefined applications for quick, reproducible results and application editor for easy customization - Rugged VACUU·VIEW extended gauge with wide measuring range offers superior chemical resistance and mechanical robustness The VACUU·SELECT fine vacuum control packages provide an easy-to-use vacuum control option for work down to 10-3 mbar. These packages include the VACUU·SELECT controller with fine vacuum gauge, a chemical-resistant inline isolation valve (VV-B 15C), and the accessories required for connection to your vacuum system via small flange (KF) connections. VACUUBRAND offers fine vacuum control packages with two different small flange connections. The KF DN 16 fine vacuum control package is compatible with our rotary vane pump models RE / RZ 2.5 to RE / RZ 6 and our HYBRID pump RC 6. The KF DN 25 fine vacuum control package is configured for use with our RE / RZ 9 rotary vane pumps and VACUU·PURE screw pumps. With its intuitive, application-based user interface, the controller allows you to quickly get your fine vacuum process under control. For advanced processes, pre-defined applications can be modified, and new applications can be created to optimize your process conditions. The included inline solenoid valve and sensor are automatically configured via the proprietary VACUU·BUS system.INCLUDED: The VACUUBRAND VACUU-Select, VACUU-VIEW, VSP 3000, and KF DN 25 Package for Fine Vacuum Control includes: - Vacuum controller VACUU·SELECT (without internal vacuum sensor and venting valve) with with VACUU·VIEW extended and power supply - Solenoid valve VV-B 15C KF DN 25 - T-piece KF DN 25 - Hose nozzle DN 15 mm (PP) - Clamping and sealing rings - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Ohaus 30400162 Modular Heat Block, 20 x 1.5 mL Eppendorf Microtubes The Ohaus 30400162 Modular Heat  (more)Block, 20 x 1.5 mL Eppendorf Microtubes is crafted from solid anodized aluminum to ensure durability and efficient heat transfer. This modular block is compatible with Ohaus HB Series Dry Block Heaters. INCLUDED: The Ohaus 30400162 Modular Heat Block, 20 x 1.5 mL Eppendorf Microtubes includes: - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Heidolph Hei-TORQUE Ultimate 200 w/ USB & RS232 Interface Overhead StirrerThe Hei-TORQUE Ultimat (more)e 200 laboratory stirrer is ideal for the powerful stirring of viscosities up to 100,000 mPas or volumes up to 50 liters (H2O). It has a wide speed range (10 - 2,000 rpm) and a maximum torque of 200 Ncm.In addition, the Hei-TORQUE Ultimate 200 offers, above all,the possibility of ramp programming, process monitoring (including timerfunction, torque trend display as a value), as well as the necessary equipment for documenting your application parameters. For this it is equipped with two interfaces - USB and RS232 - which give you the greatest flexibility to connect the device to a PC, a programmable logic controller (PLC) or an automation system such as e.g. LabManager. The scope of delivery includes the free Hei-Control software for remote control of up to 4 devices via PC.The laboratory stirrer Hei-TORQUE Value 200 performs every stirring task with minimal noise thanks to the latest engine technology. The safety-related start/stop touch-function serves to minimize the risk of unintentional switching on.Suitable for use in fume hoods or as a drive for reactor superstructures, the Hei-TORQUE Ultimate 200 has a quick -action chuck (quick chuck with safety ring) with a diameter of 10.5 mm, which can be combined with a large number of stirring tools for the best stirring results. *Stand, clamp, and impeller are sold separately* Click Here to View Product Video INCLUDED: The Heidolph Hei-TORQUE Ultimate 200 w/ USB & RS232 Interface Overhead Stirrer includes: - Power Cord - Operator's Guide - Full 3 Year Manufacturer's Warranty

Benchmark MiniMixer 3D Nutating Shaker The Benchmark MiniMixer 3D multi-functional shakers provides  (more)a 3-dimensional “nutating” motion for thorough, foam-free mixing in blood and centrifuge tubes, as well as in a variety of flat vessels. The MiniMixer comes standard with an autoclavable dimpled mat while optional flat mats are also available for mixing other vessel types. Stacking platforms can be purchased as accessories, effectively doubling the usable surface area of each model. Even the smallest single platform configuration has 24% more platform work surface than traditional nutating mixers. These mixers feature maintenance free, brushless motors capable of loads up to 2kg and are safe for use in cold rooms and incubators. INCLUDED: The Benchmark MiniMixer 3D Nutating Shaker includes: - 10 x 7.5 inch Dimpled Mat - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty