Foss 2050 Soxtex Avanti Extrac Unit with Control & Drive Units Lab

The 4titude a4S Automatic Heat Sealer requires no air supply, enabling the flexibility to be used on (more) standard lab benches as a stand-alone unit, or integrated within a robotic set up. The unit features a rapid heating element for quick start-up, and the stand-by function saves energy when the unit is not in use. The 4titude a4S Automatic Heat Sealer is compatible with a wide range of SBS footprint plates, including all PCR plate formats from 96 well to 1536 well, assay plates, deep well storage plates and microplates. Varying plate heights, from 3 mm to 60 mm can be accommodated with minimal adjustments of the instrument. Plates are presented in the portrait format and the plate position on the shuttle allows good access for robotic integration. Rolls with a width of between 75-85 mm can be loaded in either of two roll positions, depending on roll length and available space, enabling the 4titude a4S Automatic Heat Sealer to fit under the gantree of most liquid handling robots. The width and length of the applied seals are set to precisely cover an SBS footprint plate without interfering with plate stacking. The seal position can be adjusted to give an overhang at one end of the plate to facilitate ease of seal removal. Specifications: Sealing Temperature Range: 100 – 195°C Sealing Time Range: 0.1 – 10 Sec Connection: RS-232 Serial Port, USB Port Dimensions: 230 x 507 x 276 mm Weight: 27 kg

Orbit Marine AL-7100-SDU-MK2 Servo Driver Unit This was removed from a university lab where it was s (more)urplus to requirements. It is in good cosmetic condition but has not been tested at our facility.

TECTRON-L high temperature bath. Bath capacity 12 L. Adjustable temperature from room + 5ºC to 300ºC (more). Stability ± 0.1 ºC. Pump flow 12 L / min. Safety thermostat. It consists of a cooling coil through which a refrigerated liquid can be circulated, allowing it to work at temperatures below ambient temperature. TECTRON-L high temperature bath with regulator to reach temperatures up to 300ºC. It has a coil to adjust the temperature below ambient if it is connected to a refrigerated circuit.

MAS.1 Y device is an electromagnetic weighing module of high resolution, equipped with Y touch panel (more) featuring 5.7" display. The device can be integrated into a weighing system of the customer. Solid construction and advanced electronics ensure great adaptability both when fitting the module into the technological line and building it into the customer device. By cause of high measurement accuracy, it is recommended to install the module inside customer's device (e.g. in a draft shield) in order to reduce the influence of ambient conditions on the measurement result. The module comes standard with a dedicated power supply. Features: Brand new design of the electromagnetic mechanism housed in an aluminium enclosure, Readability of 0.01 mg, Overload protection, Ease of adaptation to the required storage space, Internal adjustment, Various options of hardware configuration. The Y panel functionality is remarkable thanks to use of numerous interfaces: 2×RS232, 2×USB type A, Ethernet, 4×IN, 4×OUT, Wi-Fi

Labtech LT-4000 Microplate Reader This was removed from a university lab where it was surplus to re (more)quirements. The unit powers up but we were unable to test it further at our facility. It is in good cosmetic condition with minor marks.

This Turnkey Instruments OSIRIS Environmental Particle Monitor & Tripod Housing was removed from (more) a university lab where it was surplus to requirements. The item powers on and is in reasonable used cosmetic condition. It has not been tested further at our facility. It comes in a carry case with a power supply, USB cable & other small parts/fittings. There is a software disk included. Housing Tripod Height - 135cm Last calibration date - 18/01/2022

The series of MUYA electromagnetic high resolution modules is designed to be incorporated into custo (more)mer’s weighing systems. A new generation’s MUYA 2 ultra-microbalance module is designed to fulfill our customers’ high expectations regarding mass measurements carried out with the greatest precision. The system of internal adjustment improves the quality of work even more by affecting measurements results. Operation of MUYA electromagnetic high resolution module is based on an electromagnetic digital converter. Compact design and inbuilt electronics ensure great possibilities when it comes to module's adaptation capabilities. Due to high precision of a measurement it is recommended to build the module into the customer's device (e.g. anti-draft chamber), thus limiting ambient conditions influence. Power supplier for MUYA weighing module comes standard.

IKA DB 1.3 VWR Microtube Dry Block