1Pcs Orientalmotor PK246Pb

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

ARMAGARD Industrial Computer Workstation This item was removed from a university where it was surplu (more)s to requirement. It is in reasonably good cosmetic condition and powers up, we are unable to test further at our facility.

Pair of Horizon Collators MC-8 MC-8a and MC-8m These were removed from a university lab where they w (more)ere surplus to requirements. Bot units are in reasonably good cosmetic condition and power on, but due to sustained damage, they are not fully operable and therefore, listed as Spares/Repair. The damage sustained is as follows: Part 1:The front intake has completely broken off, with the back tray significantly buckled. Part 2:The rear of the device has sustained severe damage or deformation as a result of mishandling or being dropped. The plugs have since been removed after testing the 32AMP.

Thomson Linear Micron DuraTRUE 90 Right Angle Gearhead Ratio:250:1 Y-Axis This was removed from a un (more)iversity lab where it was surplus to requirements. The unit is in good cosmetic condition but has not been tested.

Gerber DSC 1500 Single Ply Automated Fabric Cutter This item was removed from a university where it  (more)was surplus to requirement. It is in good cosmetic condition, the previous client has stated it was in working order when last used. We were unable to test it at our facility as it has been decomissioned. Features:- Table size: 240 x 158 x 85cm ( l x w x h) - Cutting area: 183 x 152cm - Cutting speed: 1.1 meters per second Also includes the following: - Gerber carriage controller unit         Serial No. 2187        Year 2008 - HP Elitedesk 800 GI TWR PC running Windows 7 installed with Gerber Cutworks 5.1 software - HP KB-1156 keyboard - Iiyana Prolite Monitor - HP mouse part No. 672651-001 - Kramer data splitter box - Instruction Manual - Mechanical and Engineering Manual - 7 x Data cables *A compressed air system of 90 - 120psi at 14L/m is required for operation.*

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Julabo SE High Tech Heating Circulator Water Bath This was removed from a university lab where it wa (more)s surplus to requirements. The unit is in good working order but is missing the plug for the drain, which will need to be replaced before it can be used. We rerouted the water with a hose for testing. It is in good cosmetic condition with minor marks.

This Stratagene MX3000P Multiplex Quantitative RT- PCR System was removed from a university lab wher (more)e it was surplus to requirements. The main unit is in reasonably good, used cosmetic condition but it does have some scrapes, scratches and marks from use. The unit powers up and both Green LEDs light. You can also feel the well block heating up. The well block is 96 hole. The system includes: 1 x Agilent Stratagene MX3000P. (various marks from use)1 x Dell Optiplex755 PC with keyboard & mouse.1 x Monitor. (various marks from use)1 x VGA Cable.1 x RS232 Cable. The PC is running a fresh install of Windows 7. Installed is a copy of Stratagene MxPro - Mx3000P v4.10 build 389.The software will control the Mx3000P unit. We have run a basic heat cycle with it and verified that the lamp will turn on & off. It has not been tested any further.

Hermle Z36-HK with High Speed 6 x 250ml Rotor The Z36 HK is the result of many years of experience i (more)n the design of universal centrifuges, high speed centrifuges and compact microcentrifuges. The result is a “Super-Speed” centrifuge with unmatched performance among benchtop centrifuges. A robust motor drive powers a variety of high speed angled rotors to speeds that would generally only be achievable in large, floor-standing ultra centirfuges. 2.0ml microtube samples can reach forces above 65,000xg, while 50ml samples, as high as 41,410xg.In addition to its high speed capabilities, the Z36 HK doubles as a universal centrifuge with a 4 x 250ml swing out rotor (offering inserts for all common tube sizes) as well as a 2 x 3 position swing-out microplate rotor. Advanced microprocessor controls allow for instant rotor identification, which automatically converts the rotational speed to the relevant g-force (rcf), preventing the user from setting a speed above the capabilities of the installed rotor. In addition to retrieving saved programs, the easy to use front panel can adjust accel/decel rates, and change the end of run alarm tone. INCLUDED: The Hermle Z36-HK with High Speed 6 x 250ml Rotor includes: - Z366-06250 6 x 250ml Rotor - Power Cord - Operator's Guide - Manufacturer's Documentation - 5 Year Manufacturer's Warranty

Benchmark Incu-Mixer MP2 Heated Plate Vortexer The new Incu-Mixer MP series by Benchmark Scientific  (more)is designed to provide an optimal method for vortexing and incubating microplates. Simultaneous heating from both the bottom surface and the lid provide temperature uniformity throughout the sample. Additionally, the heated lid minimizes evaporation and prevents condensation. A compact, 2mm orbit ensures thorough mixing in microplates without splashing. Speed, time and temperature are all displayed in real time on the large LCD screen while an internal validation system constantly monitors all parameters for accuracy. Designed for application flexibility, the Incu-Mixer series is available in two, and four-plate capacities. Independent time, temperature and speed controls allow the mixer to function as 3 machines in one; a multi-plate incubator, vortexer, or a combination of the two. The Incu-Mixer MP series is ideal for a wide variety of molecular biology applications including immunochemical reactions, enzyme and protein analysis, and microarray analysis. INCLUDED: The Benchmark Incu-Mixer MP2 Heated Plate Vortexer includes: - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty