Thermo Spectronic Genesys 10 vis UV/VIS Spectrometer

This Thermo Spectronic Genesys 10 VIS UV/VIS Spectrometer was removed from a university lab where it (more) was surplus to requirements. This item powers on and is in good cosmetic condition, it has not been tested further. Lamp hours: 327.12

Waters Micromass EMD 1000 Lab This item was removed from a university where it was surplus to requir (more)ement. It is in good cosmetic condition but does not power on, therefore it is listed as Spares/Repair.

Thermo Finnigan LCQ Advantage Mass Spectrometer Surveyor LC-MS System This was removed from a univer (more)sity lab where it was surplus to requirements. The lab confirmed that everything was in working order prior to removal. We have powered up everything but were unable to test further at our facility. All the units are in good cosmetic condition with minor marks. Included are; 1 x Thermo Finnigan LCQ Advantage Mass Spectrometer SystemSerial No. LAD00300 1 x Surveyor PDA DetectorPart No. SRVYR-PDA5Serial No. 56866 1 x Surveyor AutosamplerPart No. SRVYR-ASSerial No. 77269 1 x Surveyor MS PumpPart No. SRVYR-LPUMPSerial No. 62615 1 x Edwards 28 Vacuum PumpModel E2M28Serial No. 170517841 Supplied with:1 x Xcalibur LCQ Advantage Revision 1.3.1 x Xcalibur LCQ Advantage/DecaXP Revision 1.3 SP1.1 x Xcalibur Core Data System Software Revision 1.3.1 x Thermo MSQ 2.0 SP2 Instrument Control.1 x Thermo Xcalibur 2.1 W/Foundation 1.0.2 Rev.B.1 x Thermo Xcalibur LC Devices 2.4.0.2 x Thermo Xcalibur LC Devices 2.3.0 Software.1 x Thermo TSQ Series 2.1.1.1 x Thermo SurveyorPlus Manual Set.1 x Thermo Part No. 23043457 Start cable Integrator/Gtrace.1 x Thermo Part No. 23038071 Recorder Cable L=1900mm.1 x Emerson Industrial Automation Leroy-Somer Engine;2 x Spark Generators;1 x PULNIX 20mm CCD Camera;5 x Cables;3 x Spacer 7.7x3.2;1 x Spacer 6.3x3.2;2 x ThermoFisher Scientific Tubing Fused SI 150Ux390U;2 x Storer: TFS;1 x ThermoFisher Scientific Insulator Heater APCI;1 x O-Ring;1 x Plunger.

The LC-NMR-MS Interface is designed to sit between an HPLC system, an NMR spectroscopy probehead and (more) an MS unit. It would normally be mounted on top of the MS table immediately in front of the MS input connector. The BNMI-HP consists of 3 medium pressure (> 60Bar) syringe pumps, a 1:20 splitter, an 8-Port valve, 3 mixing chambers (T-Pieces) and associated control and interface electronics. The flow of the HPLC separations to the MS unit can be modified by pumping additional solvent from the syringe pumps. This improves the MS peak detection and shortens the time needed for the split separation to reach the MS. Separations can also be stored as a result of an MS peak detection as well as through UV absorption peak detection. The splitter splits the fluid flow from the HPLC in a 1:20 ratio. i.e. ca. 5% of the fluid is directed to the MS and the remainder to either the NMR probehead for immediate analysis or to the BPSU36 storage cassette for storage and later analysis.  The fluid directed to the MS is mixed in the mixing chamber (T-Piece) with the solvent pumped from the syringe pumps. The two left hand syringe pumps pump alternatively to guarantee a constant ’makeup’ flow. The 3rd pump at the right hand side is used to pump a calibration fluid into the flow path to allow the MS to be calibrated (or simply synchronized) at the start and end of each measurement cycle. The 8-Port valve is used to direct the fluid flow. Control of the BNMI Unit is performed using the HyStar program via an ethernet interface. Commands received from HyStar are interpreted in the BNMI Control Board. The control board then sets up the BNMI unit accordingly e.g.: Starts the pumps, changes the flow rate, turns the 8-Port valve. The splitter has a fixed mechanical function and cannot be controlled or adjusted. It simply accepts a fluid flow and splits it into 2 paths in a 1:20 ratio. However, other split ratios are available (for example 1:100 may be preferred if you have very high sample concentrations).

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Thermo Scientific HERAcell 150i CO2 Incubator Double Stack This incubator was removed from a univers (more)ity lab where it was surplus to requirements. The unit powers up and has been tested with a thermometer(not included). It is in good cosmetic condition. This unit has been professionally serviced and is in full working order. The service report is available on request.

Samples and applications - Food homogenization and preparation of spreadable creams and stuffing for (more) foods (e.g. meat, vegetables) - Preparation of cosmetics (lip balms, creams, lipsticks, ...) - Preparation of tablet coatings and homogenisation/crushing of tablets - Preparation of samples for DNA analysis, organic tissue samples and dispersions of organic tissues - Homogenisation of tobacco leaves - Preparation of pigments, inks, paints and ceramic paste - Processing of textile fibres - Dispersion of petroleum derivatives (e.g. asphalt) - Sterilization and cleaning methods: it is possible to sterilize all the components of the dispersing tool in different ways according to the construction materials and the sample processed TECHNICAL DATA - Rotor diameter: 15 mm - Stator diameter: 20 mm - Stator/rotor gap: 0.5 mm - Volume (H2O): 50 - 2,000 ml - Immersion depth: 40-175 mm - Max. speed: 25,000 rpm - Max. circumferential speed: 19.6 m/s - Ultimate fineness, emulsions: 1-10 µm - Ultimate fineness, suspensions: 10-50 µm - Max. allowable working temperature: 180 °C - Materials in contact with the medium: AISI 316L, PTFE - Suitable for solvents: Yes

M1 Mass Standard - knob weights with adjustment chamber. Nominal value - 5 kg.

Heidolph 036300420 Overhead Stirrer Impeller, PR 32 Ringed Propeller Due to its blade dimensions, th (more)e ringed pitched-blade impeller PR 32 is ideal for solutions, emulsions and suspensions in vessels with the following characteristics: ideal vessel diameter: 113-225 mm, ideal ground clearance: 23-45 mm, ideal filling level: 113-225 mm, ideal volume: 1,100-8,900 ml. The ringed pitched-blade impeller PR 32 has a total length of 400 mm and is made of stainless steel. Its stirrer shaft has a diameter of 8 mm. INCLUDED: The Heidolph 036300420 Overhead Stirrer Impeller, PR 32 Ringed Propeller includes: - Manufacturer's Documentation - 3 Year Manufacturer's Warranty

The Model 400 Hybridization oven is a high precision rotating convection oven for Northern blot and  (more)Southern blot hybridizations and other applications.