Renishaw Structural & Chemical Analyzer Model SCA SEM Raman SpectrometerLab

Julabo LC4 temperature controller Working temperature range : -50 … +350°C Temperature stability : ± (more)0.05°C Dimensions : B170 x D170 x H160 mm Weight : 3kg

This job lot of items comes from a variety of university laboratories. The items were no longer requ (more)ired, collected from various store rooms and facilities. None of these items have been tested at our site - it is likely that some will be spares/repairs, but we anticipate that a reasonable amount should operate well. None of these items have been PAT or electrical safety tested. For this reason, we have marked these as spares/repairs as they should not be used without appropriate electrical safety checks. They are sold as a spares/repairs bundle intended to be purchased by someone who has time to test and where necessary refurbish the units. It is an excellent opportunity for anyone looking to benefit from individual equipment resale. The units have not been tested at all.

New Brunswick Scientific U410 U410-86 ULT Ultra-Low Temperature Freezer Lab This was removed from a  (more)university lab where it was surplus to requirements. The unit powers up a has been tested with a digital thermometer (not included). It is in full working order but is set to -80˚C. It requires a 4 digit passcode to set it to anything else. It is in reasonably good cosmetic condition but has marks and scuffs. 4 Shelves - 57 x 55cm

This was removed from a university lab where it was surplus to requirements. Inside dimensions - D57 (more) W76.5 H126cm2 Shelves - 56 x 75cm The unit powers up and the temperature was set to -86 and dropped as low as -86˚c (thermometer read -80˚c) after running for 5 hours. The item is in reasonable cosmetic condition but it is covered in tape marks and residue, and some of the shelf door hinges are broken.

JEOL JEM-100CX II Electron Microscope Vacuum Pump This was removed from a university lab where it w (more)as surplus to requirements. The unit is untested but in reasonable cosmetic condition. It requires a connection to the main system, which we do not have.

Panasonic MDF-U55V Ultra Low Temperature Freezers ULT It is in good cosmetic condition and powers on (more), we are unable to test it further at our facility. The unit powers up and is in good working order (thermometer not included). It is in good cosmetic condition internally and externally.

LAUDA ECO Heating thermostat LAUDA ECO stands out for its range of features and ease of use. ECO the (more)rmostats are available in Silver (LCD display; simple programming) and Gold (TFT color display; complex programming) models, equipped with a mini USB interface as standard. A LAUDA innovation is the pressure flow controller located on the front of the head. This means that the regulation of the flow between inside and outside is also possible during operation. - The circulation pump can be adjusted on six levels - The ECO heating thermostats line includes transparent baths up to 100°C and stainless steel baths up to 200°C - The most powerful units are equipped with the energy-saving LAUDA SmartCool system - Temperature graphs on display - Convenient operation with softkey cursor - Mini USB interface Performance graph of the pressure pump on the six levels. TECHNICAL VISUALIZATION 1 Light sensor for automatic control of display brightness 2 Monochrome LCD display 3 Control panel (refer to following page) 4 Mains switch 5 Selector switch for dividing up the external and internal pump flow 6 Pump output for internal bath circulation 7 Pump output for bath circulation or connection to the pump connection set 8 Pt100 temperature sensor 9 Heater Display 1 - Status display 2 - Display of the internal or external temperature value (T-int or T-ext) 3 - Soft-key bar Control panel 4 - Soft keys, left and right 5 - Enter key 6 - Cursor keys for Up, Down, Left and Right. 7 - T max key: display and adjustment of the overtemperature switch-off point 1 - USB interface 2 - Upper module receptacle approx. 51 mm x 27 mm for analog, RS 232/485 module, Profibus module and contact module 3 - Lower module receptacle approx. 51 mm x 17 mm for Pt100/LiBus module 4 - Connection socket 75S for control cable of cooling underpart for RE 1050 S 5 - Rating label 6 - Connection socket 51H for power supply between the control head and cooling underpart 7 - Mains connecting lead

Single-channel electronic pipette 735061 SARTORIUS Picus 10 to 300 µl New material in its original p (more)ackaging Number of channels: 1 SARTORIUS reference: 735061 Capacity: 10-300 µl Increments: 0.20 µl Optifit tips: 350 µl Maximum volume precision: 0.15 (≤ CV%) Maximum volume precision: 0.4 (± R%) Dimensions (WxDxH): 335 x 150 x 130 mm

Including testing report (see example).

Ramp scale with stainless-steel load cells is intended for meat, fish, pharmaceutical, cosmetic and  (more)chemical industry. The scale is equipped with LD4N system allowing lifting the platform up, useful for maintenance purposes. The mechanism enables safe platform lifting and does not require physical exertion or additional equipment. Upon platform lowering, the scale is ready to carry out measurement. There is no need for recalibration. The scale is made of OH18N9 stainless steel and is equipped with PUE H315 indicator. On a customer request the scale can be made of steel of increased anti-corrosion resistance. The length of the cable for connecting the indicator to the platform - 3m. Ramp scale with LD4N system is equipped with only one ramp. Dual range weighing instrument for an additional charge. Since the scale is equipped with a platform lifting system, you are kindly requested to order a transport box (OSB box for the platform) for it. The transport box is necessary for the safe and efficient transport and storage of the ramp scale with the platform lifting system. Please take this item into consideration when planning and placing your order. If you have any questions, the Customer Service Department will be happy to assist you.

IKA R 1385 Propeller 3 - Bladed Stirrer Flow-efficient design. For drawing the material to be mixed (more) from the bottom to the top. Minimum shearing forces. Used at medium to high speeds.Stirrer Ø: 140 mmShaft Ø: 10 mmShaft length: 550 mm INCLUDED: The IKA R 1385 Propeller 3 - Bladed Stirrer includes: - Operator's Guide - Manufacturer's Documentation - 30 Day Full Parts and Labor Warranty Request a Formal Quote