BTX HT-200 Electroporation Plate Handler

The Nucleofector technology is a major improvement of the well known electroporation technology. The (more) Nucleofector technology involves a combination of optimized electrical parameters and specific Nucleofector solutions for different cell types. This combination permits the crucials step: delivery of the DNA of interest straight into the nucleus. As the DNA quickly reaches the nucleus, expression can begin without delay. The nucleofected cells are thus ready for analysis after a short incubation time of only 2 – 8 hours. DNA quality: 1 – 5 µg plasmid concentration per nuclefection sample (100 µl), plasmid concentration can be increased up to 10 µg per sample. This may lead to higher gene transfer efficiencies, but at the same time may increase mortality of the cells. Cell density: 2 x 105 – 1 x 107 cells per nuclefection sample for suspensions cells 2 x 105 – 2 x 106 cells per sample for adherent cells Cell densities of < 2 x 105 cells per smaple are not advisable beacause the gene transfer efficiency may decrease and mortality may increase. Dimensions (WxDxH): 300 x 230 x x110 mm Weight: 2.5 kg

The Gemini X2 Systems is designed for researchers who need the ultimate experiment flexibility. In o (more)ne easy setup, square wave and exponential decay waves can be applied to cells in any format. These systems incorporate remote operation functionality via footswitch or PC and internal log storage of experiment data for easy optimization, quality control requirements and troubleshooting. Electroporation of suspension cells can be achieved in 96-well plates with the HT plate handler. Usable with all cell electroporation Features: Square Waveform, Multi-Pulsing Square Wave, Exponential Decay Waveform, Multi-Pulsing Exponential Decay, Resistance/Pulse Monitoring, Experiment Log Storage, Preprogrammed Protocols, Unlimited Custom Protocol Storage, Remote Operation, PC Communications Voltage Range: 5 to 3000 V Pulse Width Range: 10 μs to 5 s Pulse Interval: 100 ms to 30 s Dimensions (DxWxH): 324 x 286 x 216 mm Weight: 7.3 kg

This BTX Electro Square Porator ECM 830 was removed from a university lab where it was surplus to re (more)quirements. The item powers on and is in reasonably good cosmetic condition, we are unable to test it further at our facility.

Electroporator Lonza 4D-Nucleofactor System. Formed by two modules: unit Core (control unit) and un (more)it-X unit-transfection). Unit X performs 16-to 32-transfections per minute. Includes instruction manual and original packaging. 2014. Specifications: 240 V; 50-60 Hz The Core Unit - Controlling the 4D-Nucleofactor™ System The X unit – Supporting Nucleofection™ of various cell numbers in different formats

E1-class mass standards are the elite in the world of metrology, because standards of this class rep (more)resent the highest level of precision and accuracy in mass measurement. The E1 classification is one of the most stringent standards that standards must meet in order to be considered the most advanced and trustworthy measurement tools. E1 - class standard: stainless steel wire Nominal value: 200 mg Material: stainless steel What Are the Characteristics of the E1 Class? Highest Precision - The allowable deviation from the actual weight is minimal, making standards of this class ideal for applications where every gram matters. Stability and Repeatability - This guarantees a consistent level of accuracy over the long term. Accurate Calibration - Standards of this class must be regularly compared with other standards of known mass to confirm their measurement accuracy. Materials with Unique Properties - E1 class mass standards are often made of materials with exceptional physical properties, which makes them stable and resistant to changes in environmental conditions. Application 1. Analytical Laboratories In analytical laboratories where accurate measurements are crucial, E1 class mass standards are used to calibrate balances with the highest precision. 2. Pharmaceutical Industry In drug manufacturing, where even the slightest deviation from the standard affects quality, E1 class mass standards are irreplaceable. 3. Scientific Research In scientific research, especially in areas requiring the highest precision, such as physics or chemistry, E1 class mass standards are used to ensure reliable results. 4. Metrology Industry In metrology laboratories where research on E1 class mass standards alone is carried out, E1 class standards are the standard of excellence. Class E1 mass standards are not only measuring tools, but also a symbol of metrological excellence. Their use affects the quality of measurements in various areas of life because they provide precision that can be relied upon. They are a key element in the world of mass measurement, shaping standards and raising the bar for all measurement tools.

Waterproof platform scales H315/HR series is designed for operation in locations with high humidity  (more)or direct contact with water. The scales is easily used in areas with no access to power supply from mains, as it features an internal rechargeable accumulator. Design Single load cell stainless steel platform scales H315 HR series is based on a terminal PUE H315 series. The terminal features large backlit LCD display and function buttons for easy operation. The terminal is installed on a pillar for easy readout of measurement result. Optionally, the scales is offered with indicator installed on a cable for mounting it on a wall. The weighing platform structure is made of stainless steel class AISI 316 with a stainless steel load cell providing the highest IP rating of 68. The scales features RS 232 interface, and optionally an additional display socket. The scales is powered from mains or internal rechargeable accumulator. Optionally, the scales can be powered from mains - 110/120VAC 60Hz (non-standard factory option).

PS.R2 series balances represent a new standard of precision balances. They feature a new, readable L (more)CD display which allows a clearer presentation of the weighing result. Besides, the display has a new text information line allowing to show additional messages and data, e.g. product name or tare value. Communication interfaces New PS.R2 balances, like previously designed PS series balances, have pans in two possible dimensions: 128x128 mm or 195x195 mm balances with a smaller pan have a draft shield. The balance precision and the measurement accuracy is assured by automatic internal adjustment, which takes into consideration temperature changes and time flow. PS.R2 balances feature several communication interfaces: 2 x RS 232, type A USB, type B USB and optional Wireless Connection. The balance may cooperate with computer by means of USB interface supposing a supplementary software has been installed (respective driver). The said driver may be downloaded from RADWAG website &ndash; SOFTWARE link or SUPPORT section. The housing is made of plastic, and the pan is made of stainless steel. The balances have a possibility to weigh products out of the pan (under-pan weighing) - the load hangs under the pan. Databases in R Series Balances The information system is based on 5 databases, which allows for several users to work with several products databases, and the registered weighing results can be subject to further analysis. The data is registered in 5 databases: users (up to 10 users), products (up to 1000 products), weighments (up to 5000 weighments), tares (up to 100 tares), ALIBI memory (up to 100 000 weighments). Quick access to information There is two directions data exchange within the system thanks to a quick USB interface. New balances allow to import and export databases using USB pen drives. Direct access to functions and databases is possible from the level of keyboard. Database - a direct access to databasis Function - a direct access to the basic functions F1 do F4 - programmable function and navigation keys on the menu ALIBI memory The used ALIBI memory is a data secure area and allows to record up to 100 000 weighment records. It ensures security of constant data register in the long time period. Under-pan weighing Weighing instruments purchased after 15th February 2023 will allow under-pan weighing at any time after the purchase. All you need to do is just to order a dedicated hook. THBR 2.0 System Cooperation with THBR 2.0 System for ambient conditions monitoring.