Copley ACI Andersen Cascade Set Collection Pan 8 Pcs without Serial Numbers

The SciLog SciCon combines temperature sensing capabilities with conductivity sensing capabilities i (more)n a compact, disposable, single-use package. Sensitivity Range 1 µS/cm to 200 mS/cm 0.1 µS/cm resolution Operating Mode/Auto Range Display Conductivity: 1 µS/cm to 200 mS/cm Temperature: 0°C to 50°C Compatible with 5 types of single use sensors (not included) Connector type Luer Compatible Tubing Sizes: ID 0.03¨ to 0.31¨ Max. Flow Rate: 1 L/min Max. Pressure: 60 psi Part Code (Packs of 5): 080-599PSX-5 Connector type 3/8¨ Barb Compatible Tubing Sizes: ID 0.31¨ to 0.38¨ Max. Flow Rate: 8 L/min Max. Pressure: 60 psi Part Code (Packs of 5): 080-594PSX-5 Connector type 1/2¨ Barb Compatible Tubing Sizes: ID 0.50¨ Max. Flow Rate: 17 L/min Max. Pressure: 60 psi Part Code (Packs of 5): 080-595PSX-5 Connector type 3/4¨ Tri-Clover (TC) Compatible Tubing Sizes: Tubing with 3/4¨ TC Max. Flow Rate: 31 L/min Max. Pressure: 60 psi Part Code (Packs of 5): 080-596PSX-5 Connector type 1¨ Tri-Clover ‘Ladish Compatible Tubing Sizes: Tubing with 1¨ TC Ladish Max. Flow Rate: 60 L/min Max. Pressure: 60 psi Part Code (Packs of 5): 080-597PSX-5

This job lot of items comes from a variety of university laboratories. The items were no longer requ (more)ired, collected from various store rooms and facilities. None of these items have been tested at our site - it is likely that some will be spares/repairs, but we anticipate that a reasonable amount should operate well. None of these items have been PAT or electrical safety tested. For this reason, we have marked these as spares/repairs as they should not be used without appropriate electrical safety checks. They are sold as a spares/repairs bundle intended to be purchased by someone who has time to test and where necessary refurbish the units. It is an excellent opportunity for anyone looking to benefit from individual equipment resale. The units have not been tested at all. ITEM-36591 Hybaid Maxi 14 Rotisserie Hybridisation Oven ITEM-36595 Hybaid Shake 'n' Stack Hybridisation Oven [condition: Used]ITEM-36596 Fisherbrand HU10 Mini-Plus Horizontal Gel Electrophoresis Unit [condition: Used]ITEM-36597 Hoefer Electrophoresis Unit [condition: Used]ITEM-36598 Hoefer Electrophoresis Unit [condition: Used]ITEM-36599 Luckham 4RT Rocking Table [condition: Used]ITEM-36607 UVP Transilluminator [condition: Used]ITEM-36608 Compaq TFT7010 Monitor [condition: Used]ITEM-36609 Thermo Hybaid PCR Express With Spare PCR Block [condition: Used]ITEM-39835 Hanna Instruments Water Test ITEM-39836 Jenway 9200 DO2 Meter ITEM-39766 Extech 407510 Heavy Duty Dissolved Oxygen Meter ITEM-39767 Job lot of Hanna Instruments Pocket PH Meters ITEM-38983 FluidX Xcap Microplate capper [condition: Used]ITEM-23169 Small desk fan SFE/1 [condition: Used]ITEM-39770 Hybaid PCR Express ITEM-39771 MJ Research PTC-225 Thermal Cycler ITEM-39772 Grant W6 Sonic Bath ITEM-37438 CBS Scientific EPS-300 X Power supply [condition: Used]ITEM-37439 SS 3H Hotplate Stirrer [condition: Used]ITEM-39774 Spectra Physics SP8480XR Scanning Detector ITEM-39775 Tyco Electronics LVC2KW Power Supply ITEM-39776 GS Laboratories 6593-10 CO2 Control Backup System Lab ITEM-39777 Spectra System AS3000 ITEM-39778 Test Tubes w/ Holding Rack ITEM-39779 Perkin Elmer L226-0103 Model LC-240ITEM-39101 Vevor Rolling Mill [condition: Used]ITEM-37443 Jenway 1000 Hotplate Stirrer [condition: Used]ITEM-39782 Pyrex 20L FlaskITEM-39783 Zippette Flask and Dispenser

Benchmark H5100-384 384 Well Plate Block for MultiTherm Touch The Benchmark H5100-384 384 Well Plate (more) Block for MultiTherm Touch is designed for use with the Benchmark H5100-HCT MultiTherm Touch Heating and Cooling Shaker. The H5100-384 is compatible with the H5100-HL Heated Lid. INCLUDED: The Benchmark H5100-384 384 Well Plate Block for MultiTherm Touch includes: - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

Boekel Scientific 1494 Concentric Ring Bath, 8 place, 115VThe Boekel Scientific 1494 ConcentricRing  (more)Bath, 8 place with adjustable water bath openings. Heavy duty 3" legspermanently attached to the body. Removable concentric rings to suit mostlaboratory containers. Analog temperature control with high and low powermodes. Two power settings, one for rapid heat up and one for reduced power consumption No wiring or assembly required Fabricated from stainless steel to ensure a long service life Supplied with water level regulator and ring sets Comes complete and ready to use. Add water and plug in. 2 year warranty Applications Solvent extraction Melting solids Evaporating liquids Analysis of total dissolved solids KD concentration Drying of wastewater sludge Chemical reactions like saponification QC departments Melting bases in crucibles Solids testingINCLUDED: The Boekel Scientific 1494 Concentric Ring Bath, 8 place, 115V includes: - Ring Sets - Water Level Regulator - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Wall-mounting kit has been designed to facilitate installation of PUE 7.1 and PUE C32 terminals on a (more) vertical surface. The kit can be mounted in two positions. Intended use: Easy installation of PUE 7.1 terminal on a vertical surface; Easy installation of PUE C32 terminal on a vertical surface; Mounting the PUE 7.1 terminal to a wall at the angle of 80°; Mounting the PUE C32 terminal to a wall at the angle of 80°; Mounting the PUE 7.1 terminal to a wall at the angle of 55°; Mounting the PUE C32 terminal to a wall at the angle of 55°. Design: The PUE-7-32 wall-mounting kit is manufactured of 1 mm steel, which provides sufficient rigidity. The kit is offered in powder coated mild steel version in colour corresponding to the colour of PUE 7.1 / PUE C32 housing. Multiple technological holes, make it possible to mount the kit in 8 points (4 mounting points for the PUE 7.1 / PUE C32 terminal and 4 mounting points for fixing to a vertical surface).

Radwag laboratory holders have been designed to facilitate faster and more convenient weighing. They (more) ensure perfect and safe fixing of small vessels of typical and non-standard shapes. Features: Maximum weighing ergonomics Direct dosing of a sample into a vessel High efficiency, lower costs (minimized potential loss of samples during transfer) Direct dosing of samples into various vessels (test tubes, round flasks, flat flasks, plastic test-tubes, titration vessels) Laboratory holders are compatible with all Radwag analytical balances. Intended use: round flasks - 50, 100 ml

Do you need a moisture analyzer that not only determines moisture or dry matter content with impress (more)ive accuracy, but also performs a digital audit, responds to your voice commands and sends you light messages? If so, learn about the functionality of the ELLIPSIS series of moisture analyzers: It Dries in 4 Ways The MA 5Y Moisture Analyzer offers you four drying profiles: standard, mild, fast and step. The standard profile is the usually used drying profile. It allows the most accurate determination of moisture content. The mild profile is designed for drying substances that are sensitive to the rapid heat released by the filaments, which heat full power at the initial stage of the process. An example of such a substance is leather. You will use the fast profile for samples with significant moisture content – of the order of even several tens of percent. The step profile will be ideal for drying substances that contain more than 15 percent moisture. Within this profile you can define any three temperatures. You will choose the values of temperature and duration of heating experimentally. What Drying Temperature Should I Set? The drying temperature determines the duration of the process. Its value depends on the type of material. If the temperature is too low, it will under-dry the sample and, consequently, unnecessarily increase the measurement time, while if it is too high, it will cause a burning effect on the material. The drying temperature for the traditional (oven) method is determined by industry or factory standards. If there are no standards, you will select the temperature experimentally. The maximum drying temperature on the MA 5Y Moisture Analyzer is 160°C. How Do I Finish the Drying? In 4 Ways The MA 5Y Moisture Analyzer has four finish modes: automatic, manual, time-defined and user-defined. Automatic mode You define the moisture loss limit value in 60 seconds. When the moisture analyzer reaches the set criterion, the measurement will automatically end. Manual mode You terminate the measurement yourself by pressing the STOP button. Time-defined mode The measurement ends after the set time has elapsed regardless of the result. You have up to 99 hours 59 minutes to manage! User-defined mode When you remove all volatiles from a sample, by definition, its mass should be constant. During drying, the dry mass of the sample is defined by a condition: if the mass of the sample is stable within 1 mg during the observation time (Auto 1-5), we consider that all volatile components have been removed from its structure. Digital Weighing Auditor Ensures that your moisture analyzer is ready for use. What is more, it informs about the need for a moisture analyzer inspection or a periodic audit of the moisture analyzer’s accuracy and sensitivity. 10-Inch Display Bigger screen – 10’’ – means more information in one place. On the new ELLIPSIS terminal, you will see up to 3 screens, widgets, graphs, statuses, notes, handy measurement history. Uncompromising User Verification For the first time ever, the moisture analyzer will verify the user using a password, RFID card, fingerprint reader, facial recognition mechanism, or any combination of these. Ambient Light – an Innovative Way for the Moisture Analyzer to Communicate With the User The light colour will tell you about status, process results, procedures, or alerts. Hotspot Use the moisture analyzer on any device connected to it. This can be a smartphone, tablet, or computer. RFID ELLIPSIS works with RFID tags* that can be used to tag your products or formulation ingredients in the database. They can also be used to identify a user. Live Note – Note Down Your Conclusions It’s the first time you can add a voice memo to a measurement series or procedure report. If you prefer to write it down, ELLIPSIS allows you to add a text note. Handy Library This is where a series of recent measurements or a report ready for digital signature, according to 21 CFR Part 11, can be found. Widgets Prepared to display what you need most at any given moment. 21 CFR Part 11 Do you work in the pharmaceutical industry? Do you need a digital signature? We are offering the moisture analyzer which as a standalone fully meets the requirements of 21 CFR Part 11/ EU GMP Annex 11. Full data security Electronic signatures Validations Electronic records Audit trails Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13.56 MHz