Grant GR150 Circulating Water Bath

Water bath from 25°C to 100°C for the laboratory The ring baths for columns, Erlenmeyer flasks or be (more)akers are suitable for continuous operation, even unattended, thanks to the standard level and lack of water monitoring. LAUDA Hydro ring water baths are available in five models, all featuring a removable perforated lid with a set of heat-resistant plastic rings. - Operations in a temperature range from 25 to 100°C. - Models H 11 V, H 19 V have been specially designed for safe use in fume cupboards. - The housings are made of stainless steel to allow their use even with chemically aggressive fluids. - Temperature regulation by knob with graduated scale - Lid with set of rings for opening the modular tank - Water level and lack control, for continuous unattended operations - The support rods (length 600 mm, diameter 12 mm), made of stainless steel, are included as standard - Hydro is protected against dry running by an electro-mechanical valve. In case of low water, the heating is stopped In the photo, simple control panel, with knob, graduated scale, warning light and safety valve. Ring opening, to adapt to different types of glassware. Standard water level regulator for continuous operation, even unattended. Safety system in case of water shortage LAUDA evaporization baths are protected against dry running by a cut-off device for lack of water (thermostatic overvoltage). The nut located on the control panel will be used to disarm the security system. Water level regulator as standard Thanks to this accessory, the loss of water inside the instrument (through evaporation) is compensated and the water level is kept constant. Furthermore, it allows use at temperatures below ambient temperatures, with a minimum of approx. 3°C above tap water temperature.

Digital temperture control and selectable display of set and actual temperature PT100 sensor Timer 1 (more) to 99 min with audible alarm Overheating protection (even when bath is empty) Capacity: 16L Outer dimensions(w x d x h): 331mm x 396mm x 265mm Bath dimensions(w x d x h): 290mm × 300mm × 190mm Weight: 10kg Including rack with 36 spaces

Grant Sub Aqua Pro Water Bath SAP18 This item was removed from a university where it was surplus to  (more)requirement. The unit powers up and has been tested with a digital thermometer (not included). It is in good cosmetic condition.

This Lauda RE210 Refrigerated Water Bath was removed from a university lab where it was surplus to r (more)equirements. The unit powers up and was tested and calibrated with our digital thermometer(not included). It is in full working order but may need calibrating to your thermometers. It is in good cosmetic condition with minor marks from use.

Julabo ED with Julabo F25 Refrigerated Circulator Water Bath This was removed from a university lab  (more)where it was surplus to requirements. The unit powers up and is in good working order. (Thermometer used for testing not included). It is in good cosmetic condition with minor marks from use.

Julabo CORIO C-B17 Open Heating Bath, 115V/50-60Hz (NRTL Certified) Working Temperature Range 20°C  (more)to 100°C Heating Capacity 1000W Volume 17L Features - Models for internal applications - Bright, white, easy to read display - Very quiet - Precise temperature control JULABO CORIO™ Immersion Heating Circulator combinations with transparent or stainless steel bath tanks for routine laboratory tasks. Units include bright LED display and easy operation. A quick connect bath clamp is included.The CORIO™ C immersion circulator provides temperatures to 100 °C for internal bath applications for use with water only.Products include a quick connect clamp for positioning the CORIO™ C on tank rim. Polycarbonate bath tanks have volume graduations in L and Qt. Stainless steel bath tanks include a drain port (except B5).INCLUDED: The Julabo CORIO C-B17 Open Heating Bath, 115V/50-60Hz (NRTL Certified) includes: - Quick Connect Clamp - Power Cord - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

The redesigned Sub-Cell GT Electrophoresis Cell offers updated features that make electrophoresis ev (more)en easier. The Sub-Cell GT Ccell is the most versatile submerged horizontal electrophoresis cell in the Sub-Cell family. Because the Sub-Cell GT cell offers the greatest choice of gel lengths, sample combs, and separation modes, it is ideal for Southern and northern blotting protocols. Up to 30 samples can be resolved over a distance of 25 cm. Using four rows of combs, the cell will run up to 120 analytical samples. Cell size (WxLxH): 180 x 405 x 94 mm Gel tray sizes (OD) (WxL): 100 x 150 mm, 150 x 150 mm ReadyAgarose gels accommodated: No Sample throughput: 1 – 120 Base buffer volume: ~1 L Buffer recirculation: No Bromophenol blue migration: ~30 mm/hr (at 75 V) This electrophoresis power supply is recommended for basic applications such as submerged horizontal and mini vertical gel electrophoresis. It offers timer control and constant-voltage or constant-current output. Output range (programmable): 10 – 300 V, fully adjustable in 1 V steps 4 – 400 mA, fully adjustable in 1 mA steps 75 W (maximum) Type of output: Constant voltage or constant current with automatic crossover Output terminals: 4 pair recessed banana jacks in parallel Timer: 1 min – 99 hr 59 min, fully adjustable Pause/resume function: Yes Safety features: No-load detection, sudden load change detection, overload/short-circuit detection, overvoltage protection Input protection: Fuse on both hot and neutral Dimensions (WxLxH): 210 x 245 x 65 mm Weight: 1.1 kg

VAT 19490 UHV Gate Valve This was removed from a university lab where it was surplus to requirements (more). The unit has not been tested but is in good cosmetic condition with minor marks.

BIOBASE BKQ-350SD-B large horizontal autoclave. Double door. Built-in steam generator. Capacity: 352 (more)L. Loading by car and trolley (included). Nine preset sterilization cycles, two test cycles and one auxiliary cycle: textile material at 121 ºC and 134 ºC, instruments at 121 ºC and 134 ºC, liquids at 121 ºC, plastic material at 121 ºC, glass and other solids at 121 ºC , Bowie-Dick test; leak test and program to be defined by the user. Camera and stainless steel cover. Automatic door closing. Illuminated indicators for door closing, running and end of cycle. Lifespan of about 10 years (20,000 cycles). Meets GMP requirements, CE marked. Water purification system, compressor and installation not included. Optional baskets and data-logging system. Camera size: 600 * 600 * 980mm. External size: 1286 * 1848 * 1240mm. Power consumption: 24Kw. Power supply: 380V, 50Hz.

E1-class mass standards are the elite in the world of metrology, because standards of this class rep (more)resent the highest level of precision and accuracy in mass measurement. The E1 classification is one of the most stringent standards that standards must meet in order to be considered the most advanced and trustworthy measurement tools. E1 - class standard: stainless steel wire Nominal value: 2 mg Material: stainless steel What Are the Characteristics of the E1 Class? Highest Precision - The allowable deviation from the actual weight is minimal, making standards of this class ideal for applications where every gram matters. Stability and Repeatability - This guarantees a consistent level of accuracy over the long term. Accurate Calibration - Standards of this class must be regularly compared with other standards of known mass to confirm their measurement accuracy. Materials with Unique Properties - E1 class mass standards are often made of materials with exceptional physical properties, which makes them stable and resistant to changes in environmental conditions. Application 1. Analytical Laboratories In analytical laboratories where accurate measurements are crucial, E1 class mass standards are used to calibrate balances with the highest precision. 2. Pharmaceutical Industry In drug manufacturing, where even the slightest deviation from the standard affects quality, E1 class mass standards are irreplaceable. 3. Scientific Research In scientific research, especially in areas requiring the highest precision, such as physics or chemistry, E1 class mass standards are used to ensure reliable results. 4. Metrology Industry In metrology laboratories where research on E1 class mass standards alone is carried out, E1 class standards are the standard of excellence. Class E1 mass standards are not only measuring tools, but also a symbol of metrological excellence. Their use affects the quality of measurements in various areas of life because they provide precision that can be relied upon. They are a key element in the world of mass measurement, shaping standards and raising the bar for all measurement tools.

C315 Load Cell Platform Scale Precision weight determination in light industrial environments at an  (more)even lighter price. Wherever fast weighing is important. The C315 scale is equipped with the PUE C315 weighing terminal with a backlit LCD display. This long-established technology guarantees reliability and low power consumption, and most importantly, a very long display life. Don’t worry about robustness The construction of the scale is made of powder-coated steel with a stainless steel weighing pan. This guarantees you work for many years, and what’s more, powder-coated steel is more environmentally friendly than traditional painting methods. You will not run out of energy The scale has two power sources: mains and rechargeable. Thanks to its well-designed electronics and LCD display, the device consumes only 5W of energy, which will allow you to work for up to 8 hours without mains power. You get battery power as standard.

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW