Nuaire NU-440-400E Biological Safety Cabinet

Exhaust Filter: 99.995% Efficiency at 0.3 Micron HEPA Filter Seal Type: HEPEX Zero Leak Neoprene Sea (more)l, Spring-loaded Lighting: Halogen Supply Filter: 99.995% Efficiency at 0.3 Micron Work Access Opening: 254 mm Height Support Frame: 673 – 826 mm Interior Dimensions (HxWxD): 724 x 1178 x 597 mm Exterior Dimensions (HxWxD): 1524 x 1362 x 841 m Weight: 227 kg

Exhaust Filter: 292 mm, 99.995% Efficiency at 0.3 Micron HEPA Filter Seal Type: HEPEX Zero Leak Neop (more)rene Seal, Spring-loaded Lighting: LED and UV Supply Filter: 376mm, 99.995% Efficiency at 0.3 Micron Work Access Opening: 254 mm Height Support Frame: 673 – 825 mm Interior Dimensions (HxWxD): 716 x 1177 x 659 mm Exterior Dimensions (HxWxD): 1495 x 1361 x 781 m Weight: 218 kg

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

This Labcaire Class II Biological Safety Cabinet Model - BH12 was removed from a university lab (more) where it was surplus to requirements. It was last used 3 years ago and the lab were confident it was working. The unit powers up and both the fans and the white lights are working. There is no UV light fitted. It is in reasonably good cosmetic condition but the metal cover for the bottom is missing its latches and won't quite fit. Inside dimensions - D62.5 W120 H70cm Hours - 14001.4

This Nuaire Labgard Class II Biological Safety Cabinet NU-437-400E  Series 6 was removed from a (more) university lab where it was surplus to requirements. The item powers on with blowers and both Light & UV working. The blower will only work when the sash is at the correct working height. This is marked on the side of the unit. When it is dropped fully the blower switches off as it should. When it is raised above the mark the windows alarm goes off as it should, until the sash is dropped back to the correct working height. The unit starts up as it should and shows 'low' airflow initially until it builds up to the correct flow. It then raises above the correct flow and the 'HI' alarm sounds. We spoke to a service engineer and they suggested that it will just require calibrating upon installation. It will need commissioning upon installation anyway. The lab reported that the filter has been removed. Inside dimensions - D57.5 W118 H72cm

CAS BioMAT 2 Class 2 Microbiological Safety Cabinet Lab This was removed from a laboratory where it  (more)was surplus to requirements. The unit powers up and is in full working order. It is in good cosmetic condition with some minor marks from use. Socket tester not included. Calibration date due: 28:02:2024. Filter details:Camfil MX14-1130X500X90.Size: 1130x500x90.Nominal Airflow: 915m3/h.Pressure Drop 92 Pa Efficiency 99.9993.Filter Class: H14 EN1822.Serial No: 111074-48187. Camfil MX14-800X320X66.Size: 800x320x66.Nominal Airflow: 415m3/h.Pressure Drop 125 Pa Efficiency 99.998.Filter Class: H14 EN1822.Serial No: 110617-46187.

The Frontier 5306 minimizes noise and interruptions in the laboratory: low input voltage power, sile (more)nt brushless motor and a rubber base that absorbs vibrations. Operator safety: rotor imbalance sensor and two safety switches that immediately stop the rotors if the lid remains open during use. Unprecedented ease of use: just place the sample in the centrifuge, close the lid and the centrifuge will start spinning without pressing any buttons. Operation AC power (included) Structure Silent brushless motor, small footprint Construction features Easy to install design Technical features Speed ​​range: 0 rpm – 6.000 rpm Maximum relative centrifugal force: 2.000 g Maximum flow rate (rotor): 8 x 1,5/2,0 ml Program memories: 0 Acceleration gear: 1 Deceleration gear: 2 Lid lock: mechanic Noise level: ≤60 ± 2 dB (A) Rotor Compatibility: Angled 8 x 1.5 / 2.0ml; Angled 4 x 8 PCR strips Execution time: continuous Safety certification: CE; FCC; TUV The Ohaus Frontier 5306 minimizes noise and interruptions in the lab: low input voltage power, a quiet brushless motor, and a vibration-absorbing rubber base. Operator safety: rotor imbalance sensor and two safety switches that stop the rotors immediately if the lid is left open during use. Unprecedented ease of use: just place the sample in the centrifuge, close the lid and the centrifuge will start spinning without the need to press any buttons. The KIT includes two rotors, described below. Maximum relative centrifugal force (x g) at 2,560 g; top speed at 6,000 rpm; tube diameter without adapter 12mm / 2.0ml, 1.5ml; outer/inner radius 45 mm. Maximum relative centrifugal force (x g) at 2,260 g; top speed at 6,000 rpm; tube diameter without adapter 12mm / 2.0ml, 1.5ml; outer/inner radius 32 mm. TECHNICAL FEATURES Speed ​​range: 0rpm – 6,000rpm. Maximum relative centrifugal force: 2,000 g. Maximum flow rate (rotor): 8 x 1.5/2.0ml. Program memories: 0. Rotor Pack: 8 x 1.5ml/2.0ml Angled Rotor; angled rotor 4 x 8 PCR strips. Accelerator gear: 1. Deceleration gear: 2. Screen (2): without display. Lid lock: mechanical. Net weight: 1.1kg. Noise level: ≤60 ±2 dB(A). Rotor Compatibility: Angled 8 x 1.5/2.0ml; angled 4 x 8 PCR strips. Rotor recognition method: not applicable. Runtime: Continuous. Safety Certification: CE; FCC; TUV.

Leitz Wetzlar Filtered Slides With Wooden Box Lab This item was removed from a university where it w (more)as surplus to requirement. This item is in good used condition, none of the contents included have been tested. All items included: 1 x S520-55-90 CB121 x K490.  K4701 x K460  K4301 x K530  K5102 x Blau BG121 x Blau BG381 x Grau 5% NG42 x Grau 0.2% NG31 x UV UG52 x UV UG11 x Diffus N

Lot of 5 x Thorlabs TC200 Temperature Controllers This job lot of items comes from a variety of uni (more)versity laboratories. The items were no longer required, collected from various store rooms and facilities. None of these items have been tested at our site - it is likely that some will be spares/repairs, but we anticipate that a reasonable amount should operate well. They are sold as a spares/repairs bundle intended to be purchased by someone who has time to test and where necessary refurbish the units. It is an excellent opportunity for anyone looking to benefit from individual equipment resale. The units have not been tested at all.

Broad performance range, from gentle mixing to high force homogenization Small footprint requires mi (more)nimal bench space Suited for homogenizing up to 4 samples in seconds Reproducible extraction of proteins and nucleic acids Simultaneously process 4 x 0.5 mL, 4 x 1.5mL, 4 x 2mL or 1 x 7mL samples

The HX7 H is a mechanical design combining into one a PUE HX7 terminal and a 4-load-cell platform, b (more)oth made of stainless steel. High protection class, IP66 / IP68, makes the HX7 H a scale that can be used in harsh industrial conditions. 4 load cells guarantee correct weighing regardless of load placing at the platform. Equipment The scale provides 7" colour graphic display and a bar graph consisting of 9 diodes emiting red and green light. The bar graph is a graphic visualisation of the current net weight referred either to the scale range or predetermined min and max thresholds. Housing back is equipped with hermetic communication interfaces such as RS232, RS485, USB, Ethernet, at your disposal there are also digital inputs/outputs and analogue output. This enables cooperation with external devices such as: barcode scanners, printers, external displays, control buttons, light signalling towers, controlling/signalling devices, systems for automatic process control, superior IT systems. With use of the bracket you can either place the terminal at any flat horizontal surface, or fix it to the wall adjusting the tilt respectively to suit your needs. Databases The terminal's software allows carrying out processes such as weighing, parts counting, dosing, labelling, formulations and percent weighing. Terminal’s system of information is based on databases: users, products, weighings, packaging, formulations, customers, ALIBI memory which guarantees stored data safety.