Thermostatic circulation bath HUBER Polystat CC1

Heating thermostat from 20 to 200°C, with LCD display and simple programming functions LAUDA ECO sta (more)nds out for its range of features and ease of use. ECO thermostats are available in Silver (LCD display; simple programming) and Gold (TFT color display; complex programming) models, equipped with a mini USB interface as standard. A LAUDA innovation is the pressure flow controller located on the front of the head. This means that flow regulation between inside and outside is possible even during operation. - Monochrome LCD graphic display for simultaneous indication of actual and set values - The circulation pump can be adjusted to six levels - Integrated programmer: 1 program with max. 20 segments - Fully electronic continuous regulator with PID action - Additional key Tmax for overtemperature protection - The ECO heating thermostat line includes transparent baths up to 100°C and stainless steel up to 200°C - The most powerful units are equipped with the energy-saving LAUDA SmartCool system - Variants in 230V; the 50 Hz are also available with natural refrigerants - Convenient operation with softkey cursor - Safety class III for operation with flammable and non-flammable liquids. - mini-USB interface - Pump connections with 13mm plastic nipples as standard LAUDA tank thermostats are equipped as standard with a cooling coil. The E 4 model is also equipped with a lid for the bowl and connections for external applications. A drain cock on the rear side makes changing the heat transfer liquid easy and safe. Heating performance graph of ECO Silver immersion thermostats with stainless steel tank. Performance graph of the pump pressing on the six levels. TECHNICAL VISUALIZATION Display 1 - Status display 2 - Display of the internal or external temperature value (T-int or T-ext) 3 - Soft-key bar Control panel 4 - Soft keys, left and right 5 - Enter key 6 - Cursor keys for Up, Down, Left and Right. 7 - T max key: display and adjustment of the overtemperature switch-off point 1 - USB interface 2 - Upper module receptacle approx. 51 mm x 27 mm for analog, RS 232/485 module, Profibus module and contact module 3 - Lower module receptacle approx. 51 mm x 17 mm for Pt100/LiBus module 4 - Connection socket 75S for control cable of cooling underpart for RE 1050 S 5 - Rating label 6 - Connection socket 51H for power supply between the control head and cooling underpart 7 - Mains connecting lead 1 - Cooling coil connections 2 - Pump connection: outflow and return (as standard only with E 4 S and ET 15 S) 3 - Four feet 1 - Mains connecting lead 2 - Rating label 3 - Bath draining tap 4 - Bath drain point

Heating thermostat Alpha: from 25 to 100°C LAUDA Alpha is the most affordable choice when it comes t (more)o high quality LAUDA thermostats. These reliable and easy-to-use thermostats, with features reduced to the essentials, can be operated with non-flammable liquids and are suitable for both indoor and outdoor temperature control tasks. The cooling system, the pump circulation set and the bath cover set are available as accessories for all thermostats. With the water cooling system, the thermostat can be used for operations from 20° to 100°C. Low-level and overtemperature protection for operation with non-flammable liquids. Qualitative characteristics - Simple and intuitive menu navigation with three-button operation via a large, clearly legible LED display - Integrated timer function to allow automatic shutdown of the device - Under / over temperature protection for operation with non-flammable liquids The back of the Alpha thermostat: clamp, power supply and reset button. Simple control with three buttons and three indicator lights: active heating, active cooling and alarm light. Can be used with any bath vessel up to 30 mm thick with the included screw clamp. Graph of pump characteristics in Alpha Lauda models. Graph of heating curves of Aplha Lauda models. TECHNICAL VISUALIZATION a - Control head with clamp b - Bath vessel c - Four mounting feet 1 - Temperature controller with four segment LED display 2 - Heater active (yellow LED is lit) Cooler active (blue LED is lit) Error signal (red LED is flashing) 3 - Menu functions, select and Enter keys 4 - Mains switch 5 - Screw clamp 6 - Tubular heater 7 - Temperature probe Pt100 8 - Pump outflow with pump outflow reducer 1 - Reset button (press only if the display shows SAFE ) 2 - Cooler cable 3 - Rating label 4 - Mains cable 5 - Screw clamp

HUBER CC303 Polystat CC3 Bath Heating and Circulation Thermostat CC 303 Circulation Water Bath with  (more)CC3 Thermostat Working temperature: 55...300°C with cooling unit: -20...300°C Dimensions (W x D x H): 335 x 382 x 433 mm Net weight: 22 kg Max. delivery capacity: 25 l/min; 0.7 Max. suction capacity: 18.5; 0.4 bar This model has been replaced by the CCx-315B vpc model

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Lauda Alpha RA 8 Cooling Thermostatic Water Bath This was removed from a university lab where it was (more) surplus to requirements. The unit powers up and is in good working order. (Digital thermometer used for testing not included). It is in good cosmetic condition with minor marks.

MORE DETAILS TO FOLLOW

Statebourne Bio 35 Nitrogen Dewar This item was removed from a university lab where it was surplus  (more)to requirements. It is in good cosmetic condition. We are unable to test it at our facility. Includes:- 6 x Metal Cylinders Double walled vacuum vessel.

Memmert ICO240 K7 CO2 Incubator w/ Active Humidity Control 241L, 115V Temperature Range Ambient +5° (more)C to 50°C Humidity Control 40 to 97% RH, or no RH Chamber Volume 241L (8.5 cu. ft.) Features - Expert precision and control for optimal protection of cultures - User-friendly, intuitive operating concept for ease of use - Allows for direct humidity control from 40 to 97% RH, or no RH - High-quality, corrosion-resistant stainless steel construction for durability and cleanliness - Easily cleanable inner chamber and housing - Rapid heating to setpoint without overshoots for consistent results - Rounded interior edges for simplified, thorough cleaning - Interior sterilization possible at 180°C for 60 minutes without removing sensors - Integrated data logger and adjustable digital timer from 1 minute to 99 days - AtmoCONTROL software for programming, data logging, and device monitoring - SetpointWAIT function ensures process timing starts only when set temperature is reached - Alarm notifications to mobile devices for enhanced safety and monitoring - Battery-buffered ControlCOCKPIT ensures continuous CO2 control even during power outages The Memmert ICO240 K7 CO2 Incubator w/ Active Humidity Control 241L, 115V offers unparalleled precision and control for demanding laboratory applications, ensuring optimal protection for cell cultures, bacteria cultures, and tissue cultures. Designed with user-friendliness in mind, it features an intuitive operating system complemented by a high-quality stainless steel inner chamber and housing that are both corrosion-resistant and easy to clean. This incubator excels in maintaining a hygienic environment with its rounded interior edges and the ability to sterilize the interior at 180°C for 60 minutes without removing sensors, promoting effortless cleaning and maintenance. Equipped with an advanced control system, the ICO240 K7 reaches desired temperatures swiftly without overshoots, and it includes a battery-buffered ControlCOCKPIT for continuous CO2 control, even during power outages. Alarm notifications can be sent directly to your mobile device, ensuring the safety and integrity of the chamber's contents. The incubator comes with an integrated data logger and a digital timer that can be set from 1 minute to 99 days and 23 hours, supporting complex ramping processes and precise temperature control. With the K7 active humidity option installed, this CO2 Incubator allows for direct humidity control from 40 to 97% RH, or no RH. Further enhancing its functionality, the ICO240 K7 features the AtmoCONTROL software for easy programming and online monitoring of up to 32 connected devices. The software enables simple drag-and-drop input of values and can send automatic alarm messages to multiple email addresses. The SetpointWAIT function ensures that process times start only when the target temperature is reached at all monitoring points. With its robust construction and high-end safety features, the Memmert ICO240 K7 CO2 Incubator is an indispensable tool for any research facility focused on cell and tissue culture. INCLUDED: The Memmert ICO240 K7 CO2 Incubator w/ Active Humidity Control 241L, 115V includes: - 2 x Stainless Steel Perforarated Shelf - Water Tank - Gas Connection Hose - 2 x Silicone Plugs - USB Drive w/ Software & AtmoCONTROL Manual - Calibration Certificate - Power Cord - Operator's Manual - Manufacturer's Documentation - 3 Year Manufacturer's Warranty

If you buy a PUE HY10 Weighing Terminal by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. HOUSING High IP rating and stainless steel facilitate operation of the terminal in challenging working conditions (high humidity, dustiness). With these two characteristics the terminal meets high hygiene standards for food and pharmaceutical industries. The terminal’s housing and base are made of stainless steel. All the HY10 connectors are fed through glands, this along with water and dust proof housing guarantee high IP rating, IP68/69. 2-point terminal-base fixing system allows limit-free LCD tilt. Option of tilt angle adjustment improves ergonomics of use and optimises indication visibility. The terminal bracket ensures its stability during operation. Rubber feet prevent unintentional device sliding. They cover openings through which the terminal can be permanently fixed either to a horizontal or vertical surface. DISPLAY 10.1” colour display of 1024x600 pixel resolution with a capacitive touchscreen Large, 10.1” backlit colour display guarantees easy-to-read information even in low light conditions. The indication can be read from a considerable distance, which increases your mobility. High resolution (1024x600) means high display readability providing crisper digits, symbols etc. Now you will not suffer from eye strain. The higher the resolution the greater comfort of use. The touchscreen stands for ease of operation, simply trust your intuition and start to operate the device. Now accessories such as mouse or keyboard are needless. Additional numeric keys and soft buttons provide maximum functionality. REMOTE CONFIGURATION It is possible to set the HY10 terminal parameters remotely, this is done using ‘Parameters Editor 2.0’ software. The parameters can also be set via the terminal. Use of ‘Parameters Editor 2.0’ software allows repeatable parameter setup. Once you set all the parameters for a particular terminal, save them to a file in order to be able to copy them to terminals operating at twinlike workstations. The set parameter configuration can be transferred either using a USB flash drive or a network. ‘Parameters Editor 2.0’ offers remote desktop option. With this solution we can carry out your terminal’s setup even if your company is located miles away from the service. SCREEN EDITOR Customized screen layout, extensive functionality. PUE HY10 terminal offers screen layout customization. You can display only those components that you find indispensable for your work. You can make decision not only on what to add to your screen but also on the size of particular components. Self-designed screen layout makes your work easier, with this weighing is no longer a time-consuming process. LABELLING Ability to design labels for each terminal-performed process. Labelling function, implemented into firmware, enables marking products with weight labels. This makes product identification fast and easy. Using ‘Label Editor’, a dedicated software, you can design label which upon being sent to the scale is available for the operator in label database. The label can provide data such as date, batch number, mass, pictogram, Ean-13 code with weight value and product code. Labelling enables: making Label Database in a terminal; assigning either a customized label to a particular product or a common label to a group of products; printing C labels (pallet) and CC labels (containers) providing total weight and quantity; automatically triggered printout of c labels. MULTI-PLATFORM OPERATION Standard design: support of one load-cell platform Optional design: support of 4 extra platforms maximum (2 internal modules plus 2 external modules) Dedicated Applications Smart Editor The application is intended for scales equipped with the HY10 terminal. It does not require any additional installations. Enter the terminal’s address in the browser address field and log in. The application enables: remote database editing import of images from the graphic file to the scale import of labels from lb file to the scale creating and preview of report, e.g. Workflow dosing processes operation Smart Display Smart Display application allows to customize the scale screen, and to display it on a computer, all this in an easy and clear way. Particular elements must be simply placed on a screen grid. Next, they can be scaled to suit user needs. The application run directly on the scale provides the user with a new, refreshed layout, and the possibility to configure the home screen. When operated via a browser on a computer, it enables remote control of the desktop, and display of enlarged mass indication. To use the Smart Display application it is necessary to run the RDA module (RADWAG Data Access) on the HY10 terminal. Extended Web Interface The application has been designed to enable the user to create his own/her own program for the PUE HY10 terminal. It facilitates exchange of basic data via JSON websocket (mass request, zeroing, taring). The application can be basis for further development, done by adding of new components, and by use of extra commands presented in „HY10 - JSON Data Exchange Interface” manual.

M1 Mass Standard - knob weights. Nominal value - 100 kg.

If you buy a Multifunctional Scale HY10 by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. Multifunctional scales HY10 series is designed to fast and precise determination of mass in industrial conditions. The HY10 scales features terminal PUE HY10 series in stainless steel housing and a single load cell weighing platform in mild steel powder coated version. The HY10 series scales features mild steel powder coated construction with stainless steel weighing platform. The terminal PUE HY10 series features a 10,1” colourful touch screen display, keyboard with numeric and function keys. The scales enable cooperating with an additional weighing platforms. Additionally, the HY10 series offers full functionality available in the terminal PUE HY10 series: programmable display and function keys, designing custom printout templates, designing text data indicated on terminal display. Multifunctional scales HY10 series are offered with a terminal connected to a weighing platform through a cable. Scales HY10 series is available in dual range version on surcharge. Dedicated Applications Smart Editor The application is intended for scales equipped with the HY10 terminal. It does not require any additional installations. Enter the terminal’s address in the browser address field and log in. The application enables: - remote databases editing - import of images from the graphic file to the scale - labels import from lb file to the scale - creating and preview of report, e.g. Workflow - dosing processes operation Smart Display The application allows to personalise the scale screen and display it on a computer. The Smart Display enables customization of the display screen in a simple and clear way. Place the individual elements on a grid visible on the screen. These elements can be further scaled to suit user needs. When operated directly on the scale, the user gets a new, refreshed look with the possibility of any configuration of the home screen. If the application is operated via a computer browser, it enables remote control of the desktop or setting larger mass indication window. The Workflow Module will improve work in your company. It enables developing a path of customized weighing process adapted to individual requirements of a particular production system, and next sending it to all weighing instruments cooperating with the E2R. The given process is started on the weighing instrument upon operator logging or after selecting a product, a formulation or an ingredient to which it is assigned. Modifications are made with use of convenient and intuitive interface.