Mini laboratory centrifuge 846070 for GREINER Bio-One microplates

Heraeus Sorvall 75006444 5650rpm 2x500g Swinging Bucket Centrifuge Rotor Lab This was removed from a (more) university lab where it was surplus to requirements. The unit is in good cosmetic condition but has not been tested. No buckets are supplied. Maximum RPM: 5650. Maximum Load: 2 x 500g.

This Beckman J2-21 Floor Standing Centrifuge was removed from a university lab where it was surplus  (more)to requirements. We have replaced the lid and repaired an area of cracked plastic underneath it. It is very stable. There are some cracks around the gas strut area. They do not appear to affect the operation of the unit. The unit is functional and has a comprehensive service history. The centrifuge holds a vacuum well and has been tested at: 5,000rpm10,000rpm15,000rpm20,000rpm (Max). It ran fine at all these speeds but the needle isn't totally in sync with the control knob. It has been tested at the following temperatures: 0ºC our thermometer read -15.8ºC20ºC our thermometer read 21.2ºC It appears to probably have a cooling issue. The compressor etc runs fine. It just appears to drop lower than it is set. When set to higher temps, it takes quite a while to heat up.

Heraeus 3335 Rotor This item was removed from a university lab where it was surplus to requirements. (more) It is in fair cosmetic condition and includes the lid. This item has not been tested. Max RPM: 20,500Max Capacity: 8 x 50mL

This Thermo Shandon Cytospin 4 Cytocentrifuge was removed from a university lab where it was surplus (more) to requirements. The unit has been inspected by a service engineer who fitted new plastic hinges fitted. The repair isn't perfect, but it's functional It also appears to have a battery error. There is a battery soldered to the main board, it probably needs replacing. The unit shows an error 4 code when first switched on but if you press stop the code goes away, and the unit starts up normally. The error relates to a discharged battery. The unit is in otherwise full working condition and is in good cosmetic condition with just the marks from the repairs.

Hermle Z216 M CentrifugeFeatures - Brushless induction drive - Microprocessor control - Active imbal (more)ance detection and cut-off - Motor driven lid lock - Emergency lid lock - Air cooling - Diagnostic program - Program memory for 99 programs - Quick-key for short runs - 10 acceleration and 10 deceleration rates, possibility of unbreaked deceleration - Permanent indication of preset and actual values - Pre-selection of speed or RCF in steps of 50/10-er - Pre-selection of running time from 10 sec to 99h 59min or continious - Simple one handed opertaion Compact, quiet, and powerful are just a few of the features found on the Z216 series microcentrifuges. Add to this, the versatility of eight available rotor options, and the result is the ideal microcentrifuge for the modern molecular biology laboratory. All common microtubes (0.2ml, 0.5ml, 1.5ml, 2.0ml) can be accepted as well as PCR strips, hematocrit tubes, and even 5.0ml centrifuge tubes. Advanced microprocessor controls allow for setting/displaying of the rotational speed in either rpm or rcf. In addition to retrieving saved programs, the easy to use front panel can adjust accel/decel rates, and change the end of run alarm tone. Despite a remarkably small footprint, the Z216 series offers a uniquely designed 44 x 1.5ml dual row rotor, nearly doubling the capacity when compared to traditional microcentrifuges. Interested in rotors and/or adapters for this centrifuge? Let us know what size tubes you are spinning, and we can help you find the right rotor and accessories for your application. INCLUDED: The Hermle Z216 M Centrifuge includes: - Power Cord - Operator's Guide - Manufacturer's Documentation - 5 Year Manufacturer's Warranty

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

ITEM-35538

KNF LAB Laboport SH810 Chemically-resistant Vacuum System Lab This item was removed from a universit (more)y where it was surplus to requirement. It is in good cosmetic condition and powers on, we are unable to test it further at our facility. This system features the following:- The system includes a 250ml separator flask on the input side.- A Shott Duran 250ml round bottom flask is included on the condenser side.- The 5-ported condenser coil is 31cm in total length and has a diameter of 6cm.

VACUUBRAND VACUU-Select, VSP 3000, and KF DN 16 Package for Fine Vacuum Control Upper Measuring Limi (more)t 750 torr Lower Measuring Limit 1 x 10-3 torr Accuracy +/- 15% of indicated value in the range 0.01-5 mbar/hPa/torr Features - Complete package for vacuum control of all fine vacuum applications in chemical labs, with continuous control range from 5 mbar to fine vacuum (10-3 mbar) - Graphic user interface for simple operation - Predefined applications for quick, reproducible results - Application editor allows easy customization - Proprietary Pirani-type fine vacuum gauge offers superior chemical resistance and mechanical robustness The VACUU·SELECT fine vacuum control packages provide an easy-to-use vacuum control option for work down to 10-3 mbar. These packages include the VACUU·SELECT controller with fine vacuum gauge, a chemical-resistant inline isolation valve (VV-B 15C), and the accessories required for connection to your vacuum system via small flange (KF) connections. VACUUBRAND offers fine vacuum control packages with two different small flange connections. The KF DN 16 fine vacuum control package is compatible with our rotary vane pump models RE / RZ 2.5 to RE / RZ 6 and our HYBRID pump RC 6. The KF DN 25 fine vacuum control package is configured for use with our RE / RZ 9 rotary vane pumps and VACUU·PURE screw pumps. With its intuitive, application-based user interface, the controller allows you to quickly get your fine vacuum process under control. For advanced processes, pre-defined applications can be modified, and new applications can be created to optimize your process conditions. The included inline solenoid valve and sensor are automatically configured via the proprietary VACUU·BUS system.INCLUDED: The VACUUBRAND VACUU-Select, VSP 3000, and KF DN 16 Package for Fine Vacuum Control includes: - Vacuum controller VACUU·SELECT (without internal vacuum sensor and venting valve) with VSP 3000 and power supply - Solenoid valve VV-B 15C KF DN 16 - T-piece KF DN 16 - Hose nozzle DN 10 mm (PP) - Clamping and sealing rings - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

HX7 H scale’s multi functions Many functions, many interfaces and great robustness (IP66/ IP68 (more)) mean many possibilities for you to use this advanced scale. Tomorrow you can apply it to a different process than today – that’s the multifunctionality. That’s the saving! Use the potential Barcode scanners, receipt printers, label printers, external displays, control buttons, light signalling towers and other controlling/ signalling devices – thanks to multipurpose software, HX7 scale can work with all of them. You can easily connect them thanks to the fact that the balance is equipped with interfaces: RS232, RS485, USB, Ethernet, 4 IN/ 4 OUT. Optionally, the balance can be equipped with 12 IN/ 12 OUT and analog output module. You can find all accessories in our regular offer. And if you have questions about compatibility, our experts will help you. Easy and pleasant Simple and convenient operation with a 7-inch color display. Perfectly visible messages additionally supported by bargraph. The top part of the operation panel features a bar graph consisting of 9 red and green diode fields. The bar graph is a graphic visualisation informing the user on a current net weight of a product presented with reference to the scale range or declared min and max thresholds. The bracket allows the terminal to be placed on any flat horizontal surface or screwed to the wall with adjustable angle. The power of steel The use of stainless steel guarantees you a long life for the scale. It is not afraid of contact with moist objects or accidental splashes. The construction of the scale is made of a stainless steel. This guarantees you work for many years. Not just weighing But also parts counting, dosing, percent weighing and formulations. The power of HX7’s working mods. Do you need ALIBI? There you have it. ALIBI memory is like a black box of a scale. It records all measurements taken on the device. The ALIBI memory cannot be modified or erased. Referring to stored weighings you can generate weighing reports, formulation reports and reports on performed control processes. Single weighing is stored in the ALIBI memory as long as it is specified by a Weighing Storage Period (days) parameter.

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Edwards nEXT240D - CF100 160W Turbomolecular Pump Ultimate Vacuum <5x10-10 mbar Inlet Connection  (more)DN100CF Pumping Speed Nominal 14,400.00 l/min Features - Reaches an ultimate pressure of 6×10⁻⁸ mbar for precise vacuum applications - Features built-in electronics compatible with TAG and TIC controllers for easy system integration - Allows for in-field servicing with minimal tooling, reducing maintenance time and cost - Upper magnetic bearing ensures clean vacuum conditions, low power consumption, and reduced vibration - Incorporates a molecular drag stage for improved pumping speed and compression ratios - Designed for long-lasting performance and low cost of ownership, enhancing value - Comes with a standard inlet screen to protect the pump and ensure optimal functionality - Offers a high level of modularity for maximum flexibility and customization nEXT turbomolecular pumps are hybrid bearing pumps with integrated controllers for pumping speeds from 47 to 1250 ls-1.The nEXT is a hybrid bearing compound turbomolecular pump. nEXT pumps combine our proven bearing technology (oil lubricated ceramic lower bearing with dry permanent magnetic upper bearing), an improved rotor design with a new molecular drag stage to deliver improved pumping speed and compression ratios, and user serviceability. They feature 24 V to 48 V DC sensorless motors with a built-in drive that is fully compatible with our range of TAG and TIC controllers.INCLUDED: The Edwards nEXT240D - CF100 160W Turbomolecular Pump includes: - Power Cord - One Year Manufacturer's Warranty