Thermo Scientific MaxQ 6000 Refrigerated Incubator Shaker SHKE6000-8CE Faulty NOTE - THIS IS A SPARES/REPAIRS ITEM

This Thermo Scientific 3311 Forma Steri-Cult Co2 Incubator was removed from a university lab where i (more)t was surplus to requirements. The unit powers up and has been tested extensively at 37˚C and 5% CO2 as well is 50% humidity. (Testing probes not included). We calibrated it to our working temperature and testing equipment, but will likely need calibrating again upon installation. It is in full working order. It is in good cosmetic condition with minor marks from use.

PHCBI CO2 Incubator Model - MCO-170AICD-PE Lab This item was removed from a university where it was  (more)surplus to requirement. The unit powers up and is in good working order (thermometer not included). Also includes the following: 1 x Shelf:  47 x 45 cm

Sartorius Certomat BS-1 Double Stack Shaking Incubator This item was removed from a university labor (more)atory where it was surplus to requirements. Both incubator units are in good used cosmetic condition and power on, but each has functional issues:- Top Unit: Heats up as expected but does not shake. - Bottom Unit: Powers up but displays an error message in German on startup and continuously loops the startup sequence. Efforts to troubleshoot both units were unsuccessful, and therefore are sold as Spares/Repair.

Heidolph Incubator 1000 High Hood XL With a height of 428 mm, this cap is particularly suitable for  (more)tall culture vessels, such as 2,000 ml Erlenmeyer flasks. Suitable for the 1000-series models of the platform shakers Duomax 1030, Polymax 1040, Titramax 1000, Unimax 1010, and Promax 1020.INCLUDED: The Heidolph Incubator 1000 High Hood XL includes: - Three Year Manufacturer's Warranty

Memmert IN450plus Natural Convection Incubator 449L, 115V Setting Temperature Range +20 to +80°C Co (more)nvection Type Natural Convection Chamber Volume 449 L (15.9 cu.ft.) Features - Setting temperature range from +20 to +80°C with a working range at least 5°C above ambient - Internal volume of 449 L (15.9 cu.ft.) for large capacity applications - Precise temperature control with 0.1°C setting resolution using 2 Pt100 sensors DIN Class A in a 4-wire circuit - ControlCOCKPIT with TwinDISPLAY offers advanced PID-microprocessor control and two high-definition TFT-color displays - Natural convection with adjustable pre-heated fresh air admixture through electronically controlled air flap - Digital timer with backwards counting, adjustable from 1 minute to 99 days - Two stainless steel, electropolished grids, with a max chamber load of 661 lbs (300 kg) - AtmoCONTROL software for data logging and program management via USB or Ethernet interface The Memmert IN450plus Natural Convection Incubator 449L, 115V is engineered for precise temperature control and optimal efficiency, making it an ideal choice for various laboratory applications. With an internal volume of 449 liters (15.9 cubic feet), this large-capacity incubator provides ample space for accommodating multiple samples and materials. The ControlCOCKPIT TwinDISPLAY system features an adaptive digital PID-microprocessor controller with dual high-definition TFT-color displays, enabling users to precisely set and monitor temperatures. The incubator's temperature range of +20 to +80°C, combined with a 0.1°C resolution, ensures highly accurate thermal conditions. Dual Pt100 sensors in a 4-wire circuit provide additional temperature monitoring, automatically taking over if an error is detected. Designed for flexibility and safety, the IN450plus offers advanced features like the HeatBALANCE function, which allows adjustments to the heating distribution between the upper and lower circuits from -50% to +50%, ensuring consistent temperature uniformity. Natural convection, combined with electronically controlled air flap adjustments, facilitates an even admixture of pre-heated fresh air. The unit is equipped with comprehensive safety measures such as AutoSAFETY and adjustable overtemperature monitors. Additionally, the AtmoCONTROL software offers intuitive programming and data logging capabilities via USB or Ethernet, making it simple to store and manage programs even in the event of a power failure. Built with a robust stainless steel interior and reinforced with deep-drawn ribbing, this incubator is both durable and easy to clean, making it a reliable choice for rigorous laboratory environments. INCLUDED: TheMemmert IN450plus Natural Convection Incubator 449L, 115V includes: - 2 Stainless Steel Grids - Tilt Protection Wall Bracket - Calibration Certificate - Power Cord - Operator's Manual - Manufacturer's Documentation - 3 Year Manufacturer's Warranty

Technical features Flow rate: 0.2-1.3 l / min Suction (max.): 3 mWg Operating pressure (max.): 1 bar (more) (rel.) Permitted fluid temperature: 5-80°C Maximum permissible viscosity: 150 cSt Valve material: FFKM Membrane material: PTFE coating Pump head material: PTFE, PP, PVDF Applications Transfer of liquids Qualitative characteristics Small footprint Simple and intuitive use Manual control Self-priming, it can run dry Splash-proof with IP65 protection rating Available with different material configurations for chemical resistance Maintenance free Pump head materials: PP, PVDF, PTFE Membrane material: PTFE coating Valve material: FFKM Simriz® VERSIONS S (standard): the flow rate can only be set manually, using the knob on the upper side, as shown in the photo. RC (remote control): the range can be controlled remotely, such as from a PC, including a fault alarm; a connection cable will be supplied. Supplied with fittings for 8 mm internal diameter tube. Download the data sheet for further information and accessories. NOT SURE WHICH VACUUM PUMPS YOU NEED? Try following our guide to KNF pumps: VACUUM PUMPS FOR THE LABORATORY Or download the KNF guide: THE IDEAL DIAPHRAGM PUMP FOR EVERY APPLICATION

This listing is for a New Brunswick U410-86 Ultra Low Temperature Freezer. The unit is in full work (more)ing condition and is ready for immediate release. Introducing the New Brunswick U410-86 Ultra Low Temperature Freezer, the ultimate solution for laboratories requiring reliable storage of sensitive medical and scientific materials. Engineered for precision, this premium upright freezer maintains a temperature range of -86°C to -50°C, ensuring optimal protection for your valuable samples. Key Features: Superior Insulation: Equipped with 5.1 inches (130mm) of traditional polyurethane insulation, the U410-86 efficiently maintains low temperatures, minimizing energy consumption. Durable Construction: The exterior is crafted from 18 gauge powder-coated steel, resistant to scratches and rust, while the polished 304L stainless steel interior offers easy cleaning and longevity. Energy Efficient: Consuming only 12.9 kWh/day, this freezer is designed to reduce operational costs without compromising performance. Rapid Pull-Down Time: Achieve set temperatures in just 4.1 hours from ambient conditions, ensuring quick access to critical samples. Technical Specifications: Capacity: 14.5 ft³ (410 litres) Dimensions: 76.8 x 26.4 x 34.1 inches (H x W x D) Weight: 518 pounds Voltage Options: Available in 120V and 208V configurations Power Consumption: 8.7 kWh/day with a full load amp draw of 16 amps Caster Wheels: Standard for easy mobility With a 25-year track record in ultra-low temperature storage, New Brunswick Scientific ensures the integrity of your research materials. The U410-86 is an excellent alternative to the Innova U535, featuring the same high-efficiency compressor system, making it a smart choice for laboratories seeking dependable performance.

GC-MS Thermo Scientific Trace GC Ultra / ITQ 1100 / TriPlus AS/HS Autosampler System This item was r (more)emoved from a university laboratory where it was surplus to requirements. All system components are in good cosmetic condition. The working condition for each unit is listed below. The Thermo Scientific Trace GC Ultra's service panel has been removed, and some components are missing. The earthing cable is disconnected. Due to the disconnected components and lack of full testing, this system is sold as Spares/Repair. Components and Condition: Thermo Scientific Trace GC Ultra - Model: K04300000000080 - Serial No.: 320070204 - Condition: Not powered on. The service panel has been removed, and some components are missing. The earthing cable is disconnected. Thermo Scientific ITQ 1100 (Polaris Q-Mass Spectrometer) - Model: Polaris Q-Mass Spectrometer - Serial No.: MS211856 - Condition: Powers on with a green power light, and fans are running. No further testing has been conducted. Thermo Scientific DPC (Direct Probe Controller) - Model: Direct Probe Controller - Serial No.: DPC 10513 - Condition: Powers on with a green power light. No further testing. Thermo Scientific TriPlus Autosampler - Model: TriPlus - Serial No.: 20088612 - Condition: Powers on with a green power light. No further testing. Thermo Scientific TP 101 - Model: TP 101 - Serial No.: 20170459 - Condition: Powers on with a green power light. No further testing. Thermo Scientific TP112 TriPlus HS Headspace Turret Injector - Serial No.: 20087277 Thermo Scientific TriPlus TP111 AS Liquid Handler Turret - Serial No.: 20172100 Included Accessories and Components: - Thermo Swap It GC/MS Interface CD - Thermo MSD Transferline Ferrule - Thermo Swap-Tight Ferrule (0.00/0.25/0.32) - Thermo Pro-Cap (0.25/0.32/0.53) - Thermo Direct Insertion Probe (Serial No.: 119300-ODIP) - Thermo TriPlus SPME Kit (Serial No.: 20084014) - Thermo ION Volume Insertion/Removal Tool - Thermo Ion Volume Holder - Alumaseal Ferrule 0.4mm (Pack of 10) - MGVF-005 (Pkt. 5) and MGVF-004 (Pkt. 4) - Thermal Fitting (Part No.: 34705451) - Seal Flat Silicone MM18X7X2 (Part No.: 29003037) - Vespel/Graphite Ferrule 1/16" x 0.5mm ID (Pack of 10) - Graphite Sealing Ring for 8mm Inlet (Pack of 2) - Filament Assembly ION Trap/DSQ II (x3) - Inlet Liner Seal for Trace 2000GCs (Pack of 2) - Graphite Vespel Ferrule for 0.1-0.25 (Pack of 10) - Graphite Vespel Ferrule for 16-003 (Pack of 10) - Graphite Vespel Ferrule for 16-16 (Pack of 10) - Graphite Vespel Ferrule for CE-005 (Pack of 1) - Various wires included

Eppendorf 16 x 15ml Adapters, Cat. # 022638726 Eppendorf 16 x 15ml Adapters, Cat. # 022638726 for A- (more)4-81 rotor. This is a 2 piece set and the adapters are new in the packaging. The Eppendorf 16 x 15ml Adapters, Cat. # 022638726 are for the Eppendorf 5810/R Centrifuges. INCLUDED: The Eppendorf 16 x 15ml Adapters, Cat. # 022638726 includes: - Full 6 Month Parts and Labor Warranty

The HX7 H is a mechanical design combining into one a PUE HX7 terminal and a 4-load-cell platform, b (more)oth made of stainless steel. High protection class, IP66 / IP68, makes the HX7 H a scale that can be used in harsh industrial conditions. 4 load cells guarantee correct weighing regardless of load placing at the platform. Equipment The scale provides 7" colour graphic display and a bar graph consisting of 9 diodes emiting red and green light. The bar graph is a graphic visualisation of the current net weight referred either to the scale range or predetermined min and max thresholds. Housing back is equipped with hermetic communication interfaces such as RS232, RS485, USB, Ethernet, at your disposal there are also digital inputs/outputs and analogue output. This enables cooperation with external devices such as: barcode scanners, printers, external displays, control buttons, light signalling towers, controlling/signalling devices, systems for automatic process control, superior IT systems. With use of the bracket you can either place the terminal at any flat horizontal surface, or fix it to the wall adjusting the tilt respectively to suit your needs. Databases The terminal's software allows carrying out processes such as weighing, parts counting, dosing, labelling, formulations and percent weighing. Terminal’s system of information is based on databases: users, products, weighings, packaging, formulations, customers, ALIBI memory which guarantees stored data safety.

If you buy a Multifunctional Scale HY10 by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. Multifunctional scales HY10 series is designed to fast and precise determination of mass in industrial conditions. The HY10 scales features a terminal PUE HY10 series in stainless steel housing and a single load cell weighing platform. The HY10 series scales is made of stainless steel OH18N9 including the weighing platform, and it is equipped with 10,1”colourful touch screen display, keyboard with numeric and function keys. The scales enables cooperation with an additional weighing platforms. Additionally, the HY10 series offers full functionality available in the terminal PUE HY10 series: programmable display and function keys, designing custom printout templates, designing text data indicated on terminal display. Multifunctional scales HY10 series is offered with a terminal connected to a weighing platform through a cable. Scales HY10 series is available in dual range version on surcharge. Dedicated Applications Smart Editor The application is intended for scales equipped with the HY10 terminal. It does not require any additional installations. Enter the terminal’s address in the browser address field and log in. The application enables: - remote databases editing - import of images from the graphic file to the scale - labels import from lb file to the scale - creating and preview of report, e.g. Workflow - dosing processes operation Smart Display The application allows to personalise the scale screen and display it on a computer. The Smart Display enables customization of the display screen in a simple and clear way. Place the individual elements on a grid visible on the screen. These elements can be further scaled to suit user needs. When operated directly on the scale, the user gets a new, refreshed look with the possibility of any configuration of the home screen. If the application is operated via a computer browser, it enables remote control of the desktop or setting larger mass indication window. The Workflow Module will improve work in your company. It enables developing a path of customized weighing process adapted to individual requirements of a particular production system, and next sending it to all weighing instruments cooperating with the E2R. The given process is started on the weighing instrument upon operator logging or after selecting a product, a formulation or an ingredient to which it is assigned. Modifications are made with use of convenient and intuitive interface.