Thermal shaker ISTHBLHTS with incubator Ohaus

Sanyo CO2 MCO-175 Incubator This item was removed from a university laboratory where it was surplus  (more)to requirements. It is in fairly good used condition, showing signs of rust around the unit. It includes four shelves and a humidifying pan, with the door catch and seal both in good condition. The unit powers up and is in good working order (thermometer & co2 analyser not included). Specifications. - Model: MCO-175 - Serial No: 20606783

This listing is for a Grifols DG Therm IncubatorThe DG Therm is a digital incubator designed for eff (more)icient gel card processing. It can hold up to 24 DG Gel cards and 24 test tubes across two independent incubation zones. The on-screen display shows the remaining incubation time and temperature, and it features a programmable alarm and removable trash bin.

Sanyo C02 Incubator Model: MCO-19AIC (UV) Lab This item was removed from a university where it was s (more)urplus to requirement. The unit powers up, is in good cosmetic condition, and has been temperature tested (thermometer & CO2 probe not included).When the CO2 was tested, the unit did not stabilize at 5% and instead rose to 8.2% - 8.4% during testing. Therefore, it is listed as Spares/Repair. Internal Dimensions: L 45cm x W 44cm x H 66cm.

Wheaton 753680-2 Reach In Incubator This was removed from a university lab where it was surplus to  (more)requirements. The unit powers up but would not heat up further than 35˚C. It is sold for spares/repairs.

PHCBI Cooled Incubator Model Type MIR-154 Labs This item was removed from a university where it was  (more)surplus to requirement. The unit powers up and is in good working order (thermometer not included). It is in good cosmetic condition internally and externally. This item requires a passcode to operate, which is available on request.

Memmert IN30 Natural Convection Incubator 32L, 115V Temperature Range At least 5°C above ambient to (more) +80°C Convection Type Natural Convection Chamber Volume 32 L Features - 32 L (1 cu.ft.) stainless steel chamber for compact sample storage - Adjustable temperature range from +20 to +80 °C, with a working range at least 5°C above ambient - 1 Pt100 sensor DIN class A in a 4-wire circuit ensures precise monitoring - ControlCOCKPIT with SingleDISPLAY, featuring an adaptive digital PID-microprocessor controller with high-definition TFT display - Natural convection system for consistent temperature distribution - Electronically adjustable air flap for pre-heated fresh air admixture - Max chamber load of 132 lbs for high-capacity sample handling - Autodiagnostic system with adjustable overtemperature monitor for added safety The Memmert IN30 Natural Convection Incubator 32L, 115V is a reliable, compact solution for precise temperature control in laboratory applications. With a 32 L (1 cu.ft.) stainless steel chamber, this incubator is designed to handle diverse sample needs within a temperature range from at least 5°C above ambient to +80°C. Equipped with a highly accurate Pt100 sensor DIN class A in a 4-wire circuit and the ControlCOCKPIT SingleDISPLAY digital PID-microprocessor, adjustments are easily managed on its high-definition TFT display. The natural convection system ensures uniform temperature distribution throughout the chamber, while an electronically adjustable air flap allows pre-heated fresh air flow. The incubator supports a maximum chamber load of 132 lbs and incorporates an autodiagnostic system with adjustable overtemperature monitoring for dependable performance and safety. INCLUDED: The Memmert IN30 Natural Convection Incubator 32L, 115V includes: - 1 Stainless Steel Grid - Tilt Protection Wall Bracket - Calibration Certificate - Power Cord - Operator's Manual - Manufacturer's Documentation - 3 Year Manufacturer's Warranty

Arcturus PixCell II Laser Capture Microdissection Microscope System Lab This system was removed from (more) a university where it was surplus to requirement. All units are in good cosmetic condition and powered up, although due to the faults listed below this system is listed as Spares/Repair.  Faults: - The PCi graphics card is faulty. - Camera not included to operate as a complete system. - The microscope does not include any eyepieces or objectives. - The control unit cable sleeving is damaged. The system comprises the following: Arcturus PixCell II Microscope Arcturus PixCell II Control unit Computer - Dell OptiPlex GX1 - Software installed: Arc200 1.0.2 Monitor - NEC MultiSyncLCD1550V

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

The new ETHOS X for the Microwave Green Extraction of Natural Products is available in two different (more) and interchangeable configurations, for fragrances and flavors. The ETHOS X takes advantage of a unique microwave selective heating mechanism to produce effective and consistent results time and time again. The fragrances configuration is based on the solvent-free microwave extraction (SFME) technology for the rapid extraction of essential oils from aromatic herbs, spices and dry seeds. The method involves placing a sample in the microwave reactor. A cooling system outside the microwave continuously condenses the vapors which are collected in a fragrances glassware. The excess of water is refluxed back to the extraction vessel to restore the in-situ water of the sample. The flavors configuration is based on the microwave hydro-diffusion and gravity technology (MHG), a new and green method of essential oils extraction from various aromatic plants. The microwave hydro-diffusion and gravity technology (MHG) combines microwave heating and earth gravity at atmospheric pressure to allow flavors to diffuse outside the plant material. Outside of the microwave oven a cooling system continuously condenses the extract. With both methods, after the essential oils are extracted they can be analyzed directly by GC-MS without any preliminary clean-up or solvent exchange steps. Including IKA RC 2 Control recirculating chiller

Vinitex door sink cabinet low White 600

PM Balances by RADWAG Laboratory Precision Under Industrial Conditions. New technology The ability t (more)o weigh loads up to 120 kg on a large weighing pan with high accuracy and good repeatability, minimum eccentricity error over the entire range, quick and stable measurement (achievable within 1 second), parameter stability over time and during transport, weighing pan dimensions adapted to the accuracy of the balance are the distinguishing features of RADWAG PM balances. All of this is possible thanks to the use of a cutting-edge measuring system based on RADWAG’s enhanced MonoBLOCK® technology. The change in the design of the monoblock has made it possible to work with a readability of 0.01 g at a maximum capacity of 20 kg and 0.2 g at a maximum capacity of 120 kg, with a repeatability of 0.01 g, and resistance to changes in ambient conditions. PM balances also include: robust design based on a larger and taller Monoblock, built-in 4-point overload protection system, IP 43 ingress protection, internal adjustment, 5" colour display, easy start-up, intuitive operation, and ergonomics. Application PM balances not only provide an accurate reading and quick measurement, but they are also versatile, allowing them to be used in a variety of industrial sectors. Dosing, formulation-making, and parts counting are just some of the possible applications of these multi-purpose devices. PM balances will find use wherever high-accuracy, high-load-capacity weighing equipment is required. Under-Pan Weighing Weighing instruments purchased after 15th February 2023 will allow under-pan weighing at any time after the purchase. All you need to do is just to order a dedicated hook. THBR 2.0 System Cooperation with THBR 2.0 System for ambient conditions monitoring. * RFID ISO/IEC 14443 Type A, 13,56 MHz

Gilson PIPETMAN M Multichannel P12x20M BT Connected Pipette PIPETMAN M Connected is a Bluetooth enab (more)led electronic pipette that offers accuracy and precision in both standard and repetitive pipetting modes. Requiring virtually no pipetting forces to aspirate and dispense samples, the PIPETMAN M Connected Pipettes help reduce pipetting fatigue and increase pipetting efficiency. The pipette interacts in real-time with TRACKMAN Connected, making planning and executing pipetting protocols faster, easier, and more reliable. The PIPETMAN M Connected Pipettes are available in 20 models covering a volume range from 0.5 µL to 10mL in single channel configurations, and 0.5 µL to 1200 µL in multichannel configurations. Accurate and Precise PipettingThe motorized piston allows for high pipetting reproducibility and accuracy in all modes. Associated with TRACKMAN Connected and its PipettePilot application, the PIPETMAN M BT Connected Series reduces the risk of human error by transferring verifiable pipetting parameters and commands in the pipette.Increased FunctionalityThe intuitive interface has five pipetting modes for a larger number of applications: pipette, repetitive, mix, reverse, and custom. Create and transfer up to 10 custom protocols from the PIPETMAN M Connected Software into your pipette. Bluetooth connection enables communication with TRACKMAN Connected and helps guide you through your protocol telling you where, when, and how much to pipette with real-time interactions.Simple and Comfortable to UseAspirate and dispense with one click of the push button and eject tips with ease. The lightweight and ergonomic design rests comfortably in your hand for maximum pipetting comfort.CLICK HERE TO SHOW GILSON PIPETTE COMPARISON TABLE INCLUDED: The Gilson PIPETMAN M Multichannel P12x20M BT Connected Pipette includes: - 5V Power Supply with AC Adapter and Cable - Four Battery & Ejector Tags - Manufacturer's Documentation - Operator's Guide - 2 Year Manufacturer's Warranty