Binder KB 53 Refrigerated Incubator

Wave shaker with Ohaus incubator These models are characterized by a slight three-dimensional wave m (more)ovement with a low foaming effect. The control panel features three independent displays with intuitive touch controls and important safety features to protect the operator and sample. - The electronic control allows you to easily adjust the angle of inclination, speed and temperature, each via dedicated controls and displays. - Precise adjustment of the angle of inclination in 1 degree increments, speed variation of 1 rev / min. and setting the temperature in 1 ° C increments. - Gradually increase the speed to the desired setpoint, to avoid splashing. - State-of-the-art motor and electronics to maintain a regular undulatory movement. Applications Hybridizations, cell cultures, absorption techniques, coloring and bleaching gels Display Independent LED displays with information on temperature, speed, tilt angle and time are easy to read and allow the operator to view all settings simultaneously Operation Detachable three-wire cable and plug (included) Structure Die-cast aluminum frame with polycarbonate lid Construction features Splash resistant construction, hot warning indicator, overload protection with audible and visual alarm in digital models and audible alarm in analog models Additional Technical Features - ISRK04HDG - Uniformity of ±0.5 at 37°C - Stepper motor drive system - CE safety certification; TUV - Speed ​​accuracy of ±1 rpm - Timer from 1 second to 160 hours

Maximum temperature: 70°C Warm-up time (air flap closed at 25°C): to 37°C; 35 min, to 50°C; 35 min,  (more)to 70°C; 45 min Recovery time (door open for 30 sec): 2 min Air changes per hour (at set temperature with flap open): 5 Spatial temperature variation (air flap closed): at 37°C; ±1.1°C, at 50°C; ±1.6°C, at 70°C: ±2.5°C Temperature fluctuation: ≤0.5°C Maximum load: 50 kg Maximum shelf load: 10 kg Volume: 107 L Internal dimensions (DxWxH): 370 x 554 x 524 mm Dimensions (DxWxH): 610 x 895 x 696 mm Weight: 69 kg

This Gallenkamp Shaking Incubator, Cat no. IOX400.XX2. Cr was removed from a university lab where it (more) was surplus to requirements. The device starts up with the shaking component functioning properly, however, the heating component is not operational. Therefore, it is listed as Spares or Repairs. It is in reasonably good cosmetic condition with minor marks.

Sanyo CO2 Incubator MCO-17AIC This was removed from a university lab where it was surplus to requir (more)ements. The unit powers up but has an issue with CO2 leaking. It is sold for spares/repairs.

Heraeus Heracell 150 Co2 Incubator Lab This item was removed from a university where it was surplus  (more)to requirement. The unit powers up and is in good working order (thermometer not included). It is in good cosmetic condition externally but the copper interior has tarnished.

Memmert IN260plus Natural Convection Incubator 256L, 115V Setting Temperature Range +20 to +80°C Co (more)nvection Type Natural Convection Chamber Volume 256 L (9 cu.ft.) Features - Setting temperature range from +20 to +80°C with a working range at least 5°C above ambient - Internal volume of 256 L (9 cu.ft.) with a maximum chamber load of 661 lbs - Precise temperature control with a 0.1°C setting resolution and 2 Pt100 sensors DIN Class A for mutual monitoring - ControlCOCKPIT with TwinDISPLAY offers adaptive multifunctional PID-microprocessor control and dual high-definition TFT-color displays - Natural convection with fresh air admixture using an electronically adjustable air flap, vent connection with restrictor flap - Comprehensive safety features including overtemperature monitor (TWW), mechanical limiter (TWB), and AutoSAFETY system with visual and audible alarms - AtmoCONTROL software for data logging and program management, with Ethernet interface and USB stick for ease of use - Stainless steel interior reinforced by deep drawn ribbing and large-area heating on four sides for even temperature distribution The Memmert IN260plus Natural Convection Incubator 256L, 115V offers unmatched precision and reliability for temperature-sensitive applications. With a spacious 256 L (9 cu.ft.) stainless steel chamber, this incubator is designed for consistent temperature control, ranging from +20°C to +80°C, with an accuracy of 0.1°C. The advanced ControlCOCKPIT system, featuring a TwinDISPLAY and adaptive multifunctional digital PID-microprocessor controller, ensures precise adjustments in temperature, air flap position, and program time, allowing for complete customization. Two Pt100 sensors in a 4-wire circuit provide mutual monitoring for accurate and consistent performance, making this incubator ideal for demanding lab environments. This incubator is equipped with essential safety features such as an overtemperature monitor (TWW), mechanical limiter (TWB), and the AutoSAFETY system, which provides visual and audible alarms for any temperature fluctuations. Additionally, the Memmert IN260plus offers natural convection and electronically adjustable fresh air admixture, enhancing airflow within the chamber. Its stainless steel interior, reinforced with deep-drawn ribbing and four-sided heating, ensures even temperature distribution and easy cleaning, while AtmoCONTROL software facilitates data logging and program management via Ethernet or USB connection. Designed for durability and optimal performance, this incubator is perfect for laboratories requiring precise, high-capacity temperature control. INCLUDED: TheMemmert IN260plus Natural Convection Incubator 256L, 115V includes: - 2 Stainless Steel Grids - Tilt Protection Wall Bracket - Calibration Certificate - Power Cord - Operator's Manual - Manufacturer's Documentation - 3 Year Manufacturer's Warranty

Vacuum systems are widely used for the aspiration and disposal of liquid waste, for instance, when r (more)emoving media from cell cultures, supernatant after centrifugation, and wash solutions from immunoassay well plates. The aspiration of waste liquids is a routine yet time-consuming task. The user-friendly VACUSAFE system streamlines this repetitive workflow, freeing up lab personnel to perform other vital tasks. It also provides a secure alternative to do-it-yourself liquid waste disposal systems typically found in laboratories, protecting operators from exposure to liquids and aerosols for a safer working environment. The system additionally features optional liquid level detection to prevent overfilling, and a filter to protect the vacuum source from contamination. Vacuum range: -300 to -600 mbar (adjustable) Pump flow rate: 8 l/min (air) Liquid aspiration rate: 17 ml/s (aspiration pipet) Noise emission: <50 dB(A) at 1 m Dimensions (HxWxD): 530 x 180 x 320 mm Weight: 3.4 kg

Exhaust gases are better removed from the furnace and discharged. The B500 – P580 controllers can b (more)e used to activate the fan automatically (not for models L 1/12, LE 1/11, LE 2/11).

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

High precision measurements The 20 kg class E2 mass standard is a precision metrology tool, ideal fo (more)r calibrating high-precision balances used in metrology, pharmaceutical, chemical laboratories and other research and industrial institutions. Product Features The ergonomic, cylindrical shape ensures ease of use and precise placement of the standard on the weighing platforms. Made from the best materials, it guarantees stability and resistance to changes in environmental conditions.

Hermle 3 x 15ml Buckets (2pk) for 4 x 100 Swing Out Rotor The Hermle 3 x 15ml Buckets (2pk) for the  (more)4 x 100 Swing Out Rotor. INCLUDED: The Hermle 3 x 15ml Buckets (2pk) for 4 x 100 Swing Out Rotor includes: - Manufacturer's Documentation - 2 Year Manufacturer's Warranty