Rigaku - XRD Parts MicroMax-007HF Rotating Anode X-Ray Generator, AFC-11R NOTE - THIS IS A SPARES/REPAIRS ITEM

Oxford Diffraction Xcalibur PX Ultra Crystal Diffraction X-ray Generator System This system was remo (more)ved from a university lab where it was surplus to requirements. The system is in very good cosmetic condition, but several units encountered issues during testing, and no PC or control software is included. As such, the system is listed for spares/repair. - Further information regarding issues faced are stated below. The lab stated it had been not used for some time but had some issues. The system units include: - Oxford Diffraction Xcalibur PX Ultra - Serial No.: XXH-127/05 - Year: 2005 - Powered on with mains light, Shutter Closed status light, inner display screen, and hand-held remote keypad all functioning - Oxford Diffraction X-ray Protection Cabinet - Serial No.: XPD-127/05 - Year: 2005 - Thermo Scientific Neslab ThermoFlex 10,000 Recirculating Chiller - Serial No.: 1111473501170217 - Powered on but shut off after 1 second with error code "PHEr" (limit fault) - Oxford Diffraction KMW200CCD CCD Detector Chiller Unit - Serial No.: CCA 73/06 - Year: 2006 - Powered on, but no further testing possible - Oxford Diffraction KMC3000C X-ray Tube Chiller - Serial No.: CAC-142/05 - Year: 2005 - Powered on, pump ran, thermostat seemed functional, but not fully tested - Oxford Diffraction Cryodrive 2.0 - Serial No.: R72-0558 - 6944 running hours - Powered on, but no further testing without gas supply - Oxford Cryosystems Cobra Controller 700 Series Cold Head Controller - Serial No.: 741174 - Powered on, displayed ambient temperature, status lights, and responsive buttons - Parker NitroFlowLab Nitrogen Generator - Model No.: 4278 - Serial No.: 4278-13NFLC0008 - Powered on, displayed a message "writing information to an SD card," and did not allow further actions - Oxford Cryosystems Standard Cobra Nitrogen Control Pump - Serial No.: CB171 - Agilent HS 602 Vacuum Pump with NW25 Oil Exhaust Filter - Model: 849-9365R001 - Serial No.: 232830 - Year: 2006 - Produced a vacuum but failed a PAT test on insulation Additional notes: - All units passed a PAT test except for the Agilent vacuum pump, which failed due to insulation issues. - The Xcalibur unit and Neslab chiller were only visually tested due to larger power plugs. Manuals included: - Oxford Instruments Object Bench Software handbook - Xcalibur Series user manual - Thermo Scientific Recirculating Chiller Operation, Installation, and Maintenance manual - Oxford Diffraction KMC3000C user manual - Oxford Cryosystems Cobra operation guide - Safety Matters cryogenic safety manual - 2 x CrysAlis Pro user manuals - Oxford Instruments Cryojet Controller UMC002 manual - Workstation 4 VMware v4.52 Virtual Machine Software and manual Accessories included: - 1 x set of keys for safety cabinet - 1 x Long Fine Focus unit (Type OD2773/00, No. 163054) - 3 x glass vacuum traps (2 litres approx.) - 2 x vacuum pump platforms - 2 x Parker wound filter cartridges (Part No.: M11R10A) - 2 x Agilent KMW3000 filter cartridges (Part No.: IJ-00-01-002) - 1 x carbon filter nitroflow mobile - 6 x data cables - 4 x Cobra stainless steel line drier units - 1 x 4-way valve purge block - 1 x box of stainless armoured hose pipe and 1/4" plastic tubing

Rigaku X-ray Diffractometer (XRD) Ultima III This system was removed from a university lab where it  (more)was surplus to requirements. The system is in reasonable used cosmetic condition. It has not been powered on at our site due to our on-site risk assessments surrounded X-Rays. Various components and parts are included as listed below, along with a PC setup, although no Rigaku software programs appear to be installed on the PC.However, there are the following software disks included: - Rigaku Basic Software (Cat No.: 9240J101) - Rigaku TTRAX3 and Ultima3 Software (Cat No.: 9240J101) - Rigaku Special Order Software (U30megaP) (Cat No.: 9999) System Specifications: - Model: Ultima III - Cat No.: 2035M410 - Serial No.: DD3654N - 6 Station Holder - Model: SA-HEM3 - Cat No.: 4057J101 - Serial No.: 00563702 - Patlite Beacon - Model: LMS-L (SN-06X03M) - Rigaku DC Motor Controller - SN: DD12866 - Rigaku Long Fine Focus - Type: R01-29-0202 - NC: 9430 022 73201 - No. DK 402688 - Rigaku CBO Cross Beam Optics - Cat No.: 2220B101 - SN: DD12793 - Additional Rigaku parts: - Cat No.: 5738E402 (SN-DD061813) - Cat No.: 2155G101 (SN-DD12804) - Cat No.: 4601K831 (SN-DD12154) - Cat No.: 4253A101 (SN-DD11586 - Vexta Stopping Motor - Model: PK543-A - SN: UR70J32307 PC Setup: - Dell Optiplex 9020 with monitor, keyboard, and mouse - The PC is in working order with all passwords cleared. It contains a few Rigaku files, but no software programs appear to be installed. Included Manuals/Software: - 2 x Rigaku D/MAX 2000/PC Series Instruction Manual - X-Ray Diffractometer Instruction Manual - Rigaku Basic Software (Cat No.: 9240J101) - Rigaku TTRAX3 and Ultima3 Software (Cat No.: 9240J101) - Rigaku Special Order Software (U30megaP) (Cat No.: 9999) Loose spare parts included: - Rigaku Cat No.: 2701E201 (SN-AD08851) - Container of round parts: Rigaku 900003 SH, w/Groove - 2 x Small containers with unknown parts - Scintag Generator Key - Key labeled: "Microscope" - Container of small metals, including: - 1 x Bag labeled "Silicon" - 1 x 640d Silicon Powder - 2 x Tubs UCAR Spectroscopic Powder - 1 x Tub labeled "Tung Flake" - Approximately 20 x small containers of Silicon metal

Rigaku MicroMax-007HF Rotating Anode X-Ray Generator, AFC-11R System Lab This system was removed fro (more)m a university where it was surplus to requirement. All units are in excellent cosmetic condition. This Rigaku X-ray generator is reportedly in working condition according to the previous owner. However, some parts, such as the detector, were removed for spares to keep another system running. No testing was conducted, as the main unit requires a transformed three-phase 400-volt to a 200-volt three-phase supply. Therefore, we cannot confirm its working condition and therefore it is listed as Spares/Repair. This system comprises the following: Rigaku MicroMax-007HFModel RA-MICRO7HFM_RACSerial No. ID211302 The main control system is mounted on a cabinet 100 cm x 60 cm x 90 cm high with a metric 2.5 cm hole spacing isolation tabletop.The operating unit mounted on the table is 40 cm x 30 cm x 55 cm high Rigaku Model AFC-11R detector base and positioning unitSerial No. ID02493 Technifab Products cryogenic sample preparation unit52 cm platform with 9 cm central hole with insulated bung26 cm diameter x 22 cm deep stainless vessel Accessories: 1 x Rigaku Osmic Varimax Optical Fixture Serial No. 25001 x Rigaku Crystallography X-ray XRF Model CU 4364F5012 x Rigaku X-Ray Diffractometer Instruction ManualsSeveral lengths of colour coded 5mm tubing1 x Hampton Research HR4-767 XYZ heated goniometer head1 x Hampton Research HR4-643 XYZ short standard goniometer head1 x PEX4S553B PCB/card to interface with 4 coms sockets

Job Lot of STOE XRD Crystallography Parts Lab These items were removed from a university where they  (more)were surplus to requirement. All XRD items are in reasonably good cosmetic condition, none of them have been powered or tested. The PC has been powered on and has the following software installed:- Winxpow Software No password is required (press 'Cancel' when the computer asks for a password).This PC runs on Microsoft Windows 95. This item is also supplied with various keys and power cables.

SAFETY FIRE CASE TYPE 30 - CHEMISAFE - Completely made of electrogalvanized steel sheet with a thick (more)ness of 1 - 1.5 mm, cold bent - Gray RAL7031 - External finish made of acid resistant epoxy resin and passage through a thermal tunnel at 200 °C - Cabinet insulation with high density rock wool panels and calcium sulphate panels - Automatic closing of the lid when the ambient temperature exceeds 50°C 30 mm heat-expanding insulating gaskets which, in the event of a temperature increase, guarantee perfect sealing of the container according to the EN14470-1 standard - Non-standard trolley - Side handles - Lid with lock and key - 1 retention tank in painted steel - ISO 3864 : signs with pictograms - Certified as fire resistant for 30 minutes, according to EN14470-1 BV (Bureau Veritas Supplied: - 1 stainless steel retention tank (capacity 1.5 litres) Optional: - Wall mounting - Internal carbon dioxide fire extinguisher with automatic thermal activation (62 °C) - Cart - Pipe passage (chromatography) APPLICATION: CPG/HPLC CHROMATOGRAPHY Storage of solvents in a portable fire-resistant container and linked to the chromatographic chain via small tubes. The tubes are connected through a fire resistant passage with a diameter of 2 cm located on the lid of the container. In the photo the convenience of the CHEMISAFE transport box. Versatile and very useful. Sturdy structure and metal door straps ensure you a long life. With the optional trolley, very easy to transport anywhere. WHAT IS CHROMATOGRAPHY? Chromatography is a process for separating the components of a mixture. To start the process, the mixture is dissolved in a substance called the mobile phase, which carries it through a second substance called the stationary phase. To know more: Cromatografhy On our webshop there are only some of the models that can be ordered. If you are interested in all the possibilities available, contact us. DO YOU NEED HELP? Do not hesitate to contact us, our CHEMISAFE product expert will help you choose the model that best suits your needs or design the perfect set for your laboratory. Go to the CONTACT form ➞

This item has just arrived in our stock. Please enquire for further details.

Heto Maxi Dry Plus VR Maxi Vacuum Centrifuge Lab This item was removed from a university lab where i (more)t was surplus to requirement. It is in reasonable condition and powers on, however there's a fault with the lock mechanism that prevents the lid from opening. Therefore, further testing could not be conducted and it is listed as Spares/Repair.

Ohaus Aquasearcher a-AB33PH-B pH Meter The next step in the evolution of OHAUS’ original Starter Ser (more)ies, the all-new AQUASEARCHER™ AB33PH bench meter is designed to be reliable, efficient, and user-friendly. The i-Steward ensures repeatable and consistent measurement accuracy for optimal peace of mind. The large LCD display and touch keypad makes changing the parameters, executing setup, and performing calibration as simple as using a smartphone.INCLUDED: The Ohaus Aquasearcher a-AB33PH-B pH Meter includes: - Power Cord - a-AB33PH Benchtop Meter - Stand-Alone Electrode Holder - Two Year Manufacturer's Warranty

Memmert IN30 Natural Convection Incubator 32L, 115V Temperature Range At least 5°C above ambient to (more) +80°C Convection Type Natural Convection Chamber Volume 32 L Features - 32 L (1 cu.ft.) stainless steel chamber for compact sample storage - Adjustable temperature range from +20 to +80 °C, with a working range at least 5°C above ambient - 1 Pt100 sensor DIN class A in a 4-wire circuit ensures precise monitoring - ControlCOCKPIT with SingleDISPLAY, featuring an adaptive digital PID-microprocessor controller with high-definition TFT display - Natural convection system for consistent temperature distribution - Electronically adjustable air flap for pre-heated fresh air admixture - Max chamber load of 132 lbs for high-capacity sample handling - Autodiagnostic system with adjustable overtemperature monitor for added safety The Memmert IN30 Natural Convection Incubator 32L, 115V is a reliable, compact solution for precise temperature control in laboratory applications. With a 32 L (1 cu.ft.) stainless steel chamber, this incubator is designed to handle diverse sample needs within a temperature range from at least 5°C above ambient to +80°C. Equipped with a highly accurate Pt100 sensor DIN class A in a 4-wire circuit and the ControlCOCKPIT SingleDISPLAY digital PID-microprocessor, adjustments are easily managed on its high-definition TFT display. The natural convection system ensures uniform temperature distribution throughout the chamber, while an electronically adjustable air flap allows pre-heated fresh air flow. The incubator supports a maximum chamber load of 132 lbs and incorporates an autodiagnostic system with adjustable overtemperature monitoring for dependable performance and safety. INCLUDED: The Memmert IN30 Natural Convection Incubator 32L, 115V includes: - 1 Stainless Steel Grid - Tilt Protection Wall Bracket - Calibration Certificate - Power Cord - Operator's Manual - Manufacturer's Documentation - 3 Year Manufacturer's Warranty

Multifunctional scales TMX H is designed to fast and precise determination of mass in industrial con (more)ditions. TMX H Multifunctional scales TMX H comprises terminal PUE 5 and a weighing platform. Labelling system series TMX H is used to print labels for marking weighted goods e.g. in the process of packing. The program can generate standard labels for single goods. Functionality of the software: a function of weight control (weighing control + / -), previewing weighments carried out on weighing terminal as a table of weighments, simplified reporting module allowing the report to be generated, creation of label templates from labels in weighing terminal, identification of goods by using the code EAN-13 and EAN-128, quick search using the range of barcode scanner, the availability of databases: the operators, products, clients, warehouses, tares (packages), etc. The application enables measurements execution and their record into a local database or on the server. Networked terminals allow transmission of the measurements to the parent database installed on the server. The ability to work with a computer program E2R SYSTEM. Terminal types: PUE 5.15R, PUE 5.19R – resistive touch screen technology. Protection class IP68. High resistance to moisture and dust. In comparison to remaining models, limited brightness and lower resistance to shocks and scratches. Possibility of operation using gloves preventing scratches (latex, material). PUE 5.15IR, PUE 5.19IR – infrared touch screen technology. Protection class IP68. Very high brightness and readability level. High resistance to moisture and dust. High mechanical resistance, possibility of operation using gloves (made of latex, material or even steel chain). PUE 5.15C, PUE 5.19C – capacitive touch screen technology. Protection class IP68. High brightness and readability level. High resistance to moisture and dust, good mechanical resistance. Absolute precision of touch detection, sensing multiple points of touch (multi-touch).