Job Lot of 6 Hewlett Packard 1100 Series HPLC Units Spares or Repairs NOTE - THIS IS A SPARES/REPAIRS ITEM

This item has just arrived in our stock. Please enquire for further details.

System contains: Solvent tray Vacuum degasser Binary pump Autosampler Thermostatted colomn compartme (more)nt Variable wavelength detector Vacuum degasser: The Agilent 1100 HPLC Degasser features a 4-channel vacuum container, including four tubular plastic membranes, and a vacuum pump. This degasser has a maximum flow rate of 0-10ml/min flow rate per channel and 5-10ml/min at reduced degassing performance. Binary pump: Flow Precision: <0.3 % RSD (typically <0.15 % RSD) Flow Range: Setpoints from 0.001 to 5.0 ml/min,  in 0.001 ml/min increments Operating range: 0 – 40 MPa (0 – 400 bar, 0 – 5880 psi) Pulsation: <2 % amplitude (typically <1 %) at 1 ml/min isopropanol at all pressures >1 MPa (> 10 bar, >147 psi) Compressibility compensation: User selectable, based on mobile phase compressibility Delay volume: 180 – 480 µl (600-900 µl with mixer) dependent on back pressure Recommended pH range: 1.0 – 12.5. Solvents with pH <2.3 should not contain acids which attack steel Well-plate autosampler: Safety features: Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display Injection range: 0.01 – 8 µl in 0.01 µl increments Precision: Typically < 0.5 % RSD of peak areas from 5 – 40 µl, Typically < 1 % RSD from 1 – 5 µl, Typically < 3 % RSD from 0.2 – 1 µl Sample viscosity range: 0.2 – 5 cp Sample capacity: 2 × well-plates (MTP) + 10 × 2 ml vials, 100 x 2 ml in one tray, 40 x 2 ml in half tray Injection cycle time: Typically < 30 s using following standard conditions: Default draw speed: 4 µl/min, Default eject speed: 10 µl/min, Injection volume: 0.1 µl Carry-over: Typically < 0.05 % using the following conditions: Column: 150 x 0.5 mm Hypersil ODS, 3 µm Mobile phase: Water/Acetonitrile = 85/15 Column Flow rate: 13 µl/min Injection volume: 1 µl caffeine (=25ng caffeine), 1 µl water to test carryover. Outside wash of needle before injection: 20 sec with water using flush port Thermostatted colomn compartment: Temperature range: 10 degrees below ambient to 80 °C, up to 80 °C: flow rates up to 5 ml/min Temperature stability: ± 0.15 °C Temperature accuracy: ± 0.8 °C (± 0.5 °C With calibration) Column capacity: Three 30 cm Warm-up/cool-down time: 5 minutes from ambient to 40 °C, 10 minutes from 40 – 20 °C Dead volume: 3 µl  Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN via other series module Safety and maintenance: Extensive diagnostics, error detection and display (through control module and Agilent ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Variable wavelength detector: Detection type: Double beam photometer Light source: Deuterium lamp Wavelength range: 190 – 600 nm Wavelength accuracy: ± 1 nm Bandwidth: 6.5 nm Linearity:> 2AU (5%) upper limit Flow cell standard: 14 µl volume, 10 mm cell path length, 40 bar

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

System contains: Solvent tray Vacuum degasser: G1322A Vacuum degasser: The Agilent 1100 HPLC Degasse (more)r features a 4-channel vacuum container, including four tubular plastic membranes, and a vacuum pump. This degasser has a maximum flow rate of 0-10ml/min flow rate per channel and 5-10ml/min at reduced degassing performance. Quaternary pump: Hydraulic system: Dual plunger in series pump with proprietary servo-controlled variable stroke drive, floating plungers and active inlet valve Setable flow range: 0.001 – 10 ml/min, in 0.001 ml/min increments Flow range: 0.2 – 10.0 ml/min Flow precision: < 0.07% RSD, or < 0.02 min SD whatever is greater, based on retention time at constant room temperature Flow accuracy: ± 1% or 10 µl/min whatever is greater Pressure: Operating range 0 – 400 bar up to 5 ml/min, 0 – 200 bar up to 10 ml/min Pressure pulsation: < 2 % amplitude (typically < 1 %), at 1 ml/min isopropanol, at all pressures > 10 bar Compressibility compensation: User-selectable, based on mobile phase compressibility Recommended pH range: 1.0 – 12.5, solvents with pH < 2.3 should not contain acids which attack stainless steel Gradient formation: Low pressure quaternary mixing/gradient capability using proprietary high-speed proportioning valve Delay volume 800 – 1100 µl, dependent on back pressure Composition Range: 0 – 95 % or 5 – 100 %, user selectable Composition Precision: < 0.2 % RSD, at 0.2 and 1 ml/min Autosampler thermostat: Temperature range: setable from 4°C to 40°C in 1°C increments Temperature accuracy (at ambient temperatures < 25 °C and humidity < 50%): – 1°C to + 4°C at a setpoint of 4°C Temperature accuracy (at ambient temperatures > 25 °C and/or humidity > 50%): – 1°C to + 5°C at a setpoint of 4°C Standard autosampler: Pressure: Operating range 0 – 400 bar GLP features: Early maintenance feedback (EMF), electronic records of maintenance and errors Safety features: Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display Injection range: 0.1 – 100 µl in 0.1 µl increments Replicate injections: 1 – 99 from one vial Precision: <0.25% RSD from 5 – 100 µl, <1% RSD 1 – 5 µl Minimum sample volume: 1 µl from 5 µl sample in 100 µl microvial, or 1 µl from 10 µl sample in 300 µl microvial Carryover: Typically <0.1% Sample viscosity range: 0.2 – 50 cp Replicate injections per vial: 1 – 99 Sample capacity 100 x 2 ml vials in 1 tray Injection cycle time: Typically 50 s depending on draw speed and injection volume Thermostatted colomn compartment: Temperature range: 10 degrees below ambient to 80 °C, up to 80 °C: flow rates up to 5 ml/min Temperature stability: ± 0.15 °C Temperature accuracy: ± 0.8 °C (± 0.5 °C With calibration) Column capacity: Three 30 cm Warm-up/cool-down time: 5 minutes from ambient to 40 °C, 10 minutes from 40 – 20 °C Dead volume: 3 µl Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN via other series module Safety and maintenance: Extensive diagnostics, error detection and display (through control module and Agilent ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Diode array detector: Detection type: 1024-element photodiode array Light source: Deuterium and tungsten lamps Wavelength range: 190 – 950 nm Short term noise (ASTM) Single and Multi-Wavelengt: ± 1 × 10-5 AU at 254 and 750 nm Drift: 2 × 10-3 AU/hr at 254 nm Linear absorbance range: > 2 AU (upper limit) Wavelength accuracy: ± 1 nm Self-calibration with deuterium lines, verification with holmium oxide filter Wavelength bunching: 1 – 400 nm Programmable in steps of 1 nm Slit width: 1, 2, 4 , 8, 16 nm Programmable slit Diode width: < 1 nm Flow cells: 13 µl volume, 10 mm cell path length and 120 bar (1760 psi) pressure maximum Control and data evaluation: Agilent ChemStation for LC Analog outputs: Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, two outputs Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Safety and maintenance: Extensive diagnostics, error detection and display through control module and ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. GLP features: Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user-settable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with built-in holmium oxide filter.

GE Healthcare Asymptote VIA Thaw CB1000 Cryo Cell Therapy Bags Dry Thawing LabSerial No. TBA0618004S (more)oftware Version 1.3.17-06f731 This item was removed from a university where it was surplus to requirement. It is in very good cosmetic condition and working order. (Thermometer not included.) Thaw loading temperatures -196˚C to 0˚CThaw temperatures 34˚C to 0˚C The size of the cryo bags to be thawed is selectable from 25ml to 275ml.

This Leica Reichert Ultracut S Microtome &amp; Controller was removed from a university lab where it (more) was surplus to requirements. The unit powers up and is in good working order. The lights work, and the microtome itself is mechanically sound. Leica Reichert Ultracut SType - 702501SN - 420699 StereoZoom 6Zoom Range 0.67X - 4.0X 2 x Eye Pieces 15X W.F. Stereo (31-05-62) ControllerType - 654901SN - 89465

Heidolph Hei-VAP Core ML/G3 Non Coated Motor Lift w/ G3 Vertical GlasswareThe Hei-VAP Series of rota (more)ry evaporators was developed with an emphasis on the essentials: well thought-out details with a focus on features and functions to facilitate everyday laboratory work. Standard models are designed without vacuum control. These systems are for integration into an existing vacuum system or for configuration with optional vacuum controller. The PTFE vacuum seals are highly resistant and can achieve maximum tightness and reduce expensive spare parts. The 210℃ universal heating bath is suitable for all flasks up to 5 liters. Conveniently adjust the angle of inclination between 20° and 80° with a maximum height of 160mm. Corrosion free die cast housing features condensation repellent varnish. The Heidolph Hei-VAP Core features an operating concept that is focused on the essentials: clear and with access to the basic parameters rotation speed and heating bath temperature at any time. Two separate knobs with dynamic control for setting the rotation speed and heating bath temperature: fast turning for large jumps, slow turning for precise setting of the set values. The Intuitive LED ring light system makes activated functions clearly visible even from a distance. Features: - Digital display - Direct access to rotation and heating bath temperature - Lock function - Standby button - Residual heat warning Click Here to View Product Video INCLUDED: The Heidolph Hei-VAP Core ML/G3 Non Coated Motor Lift w/ G3 Vertical Glassware includes: - Heating Bath - Control Panel - G3 Vertical Glassware - 1 Liter Receiving Flask - 1 Liter Evaporating Flask - Vapor Tube - Vacuum Seal - Power Cord - Operator's Guide - Full 3 Year Manufacturer's Warranty

Refurbished device.. Great condition. 6 Months warranty. PN: 1645070 The PowerPac Universal power su (more)pply fits the broadest range of applications of all power supplies on the market, from mini vertical and high-throughput electrophoresis to blotting. Features and Benefits - User intuitive programming permits multistep (up to 9 steps) methods and timed runs with a choice of constant voltage, current, or power output. - LCD screen displays all run parameters at once - User optional run completion after an AC power failure - Constant voltage, constant current, or constant power operation with automatic Crossover - Stackable case with adjustable viewing angle via flip down legs Applications and Uses - Nucleic acid gel electrophoresis - Protein gel electrophoresis Specifications: - Volts: 10–500 V - Current: 0.01–2.5 A - Power: 1–500 W - Type of output ((with automatic crossover): Constant voltage, constant current, or constant power - Timer: 1 min–99 hr, 59 min - Volt-hour control: Yes, 99,000 V-hr - Programmable methods: Stores 9 methods, each with up to 9 steps - Real-time clock: Yes - Number of output jack: 4 sets in parallel

Capacity: 30 g/ 60 g/ 110 g/ 160 g Readability: 1 mg/ 2 mg/ 5 mg/ 10 mg Reproducibility: ±1 mg/ ±2 m (more)g/ ±5 mg/ ±10 mg Linearity: ±1 mg/ ±2 mg/ ±5 mg/ ±10 mg Response time: 2 sec Weighing plate: Ø 80 mm Weighing chamber height: 200 mm Weight: 5.5 kg

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW