Applied Biosystems MDS Sciex 3200 Q Trap LC/MS/MS System With PC Lab

This system was removed from a university lab where it was surplus to requirements. All units power  (more)up but this has not been tested further as a system. It is in reasonably good cosmetic condition with marks from use. Included are; 1x Waters Pump Control Module IIModel: PC2S/N: K05PC2 650E 1x Waters Temperature Control Module IIModel: TC2S/N: H05TC2 641E 1x Waters 515 HPLC PumpModel: 515S/N: L05515 088A 1x Waters Column Fluidics OrganizerModel: APCS/N: K05APC 452M 1x Waters 2767 Sample ManagerModel: 2767 SAMPLE MGR.Part no: 725000299S/N: H05XY6 738MSample tubes fit 16ml vials. 1x Samsung MonitorModel: 171S SS/N: GH17HJCTB07621N 1x AOC LCD MonitorModel: LM520 AS/N: T5GJ32AR05528 1x Fujitsu Siemens Mouse1x Acer Mouse1x Acer KB-0759 Keyboard1x BTC 5197 Keyboard 1x Applied Biosciences Programmable Absorbance DetectorModel: 785AS/N: 29511519 1x IBM ThinkCentre PCMT-M 8143-QGHS/N: LMPM2TKThe hard drive has been removed from the PC.We are certain it was paired up with Control Modules. 1x HP vw8400 WorkStationS/N: CZC7113H1HMassLynxMassLynx DiversitySirius Analytical Instruments 1x Waters Column Heater ModuleModel: CHMS/N: M05CHM174M 1x Waters Leak Sensor Module 1x Gilson 506C System Interface ModuleS/N: 369J8PA500 1x Waters Fraction Collector III Ver.W2.01Model: WFCS/N: D06WFC178J 1x Perkin Elmer Series 200 LC PumpS/N: 291N 5110302 1x S-Video Mini-DIN 4-pin1x RS-232C Serial Cable1x Control Cable Assembly1x SCSI I to SCSI II Cable1x Drive Cable 25 Pin male/male 1x Waters 2525 Binary Gradient Module Installation & Maintenance Guide1x Waters 2767 Sample Manager Injector Installation & Maintenance Guide1x Waters 515 HPLC Pump Operator's Guide1x Performance Maintenance Protocol 2007-20091x Waters Purification of Compounds - Using FractionLynx

This system was removed from. a university lab where it was surplus to requirements. The unit has be (more)en professionally serviced and is in full working order. It is in good cosmetic condition with minor marks. Included are; AS50:Powers up okPassed all internal checksInstalled options tested/checkedInject port alignment okFirmware 1.10Bios 30.00All ok UVD170U:Connects successfully to Chromeleon v6.8 (USB)Lamps switch on/offPowers on okChromeleon reports no errors GP50:Powers on okAll internal tests passedRan pump to pressure 2.0ml/min at 1000psi variance < 3psi/5 mins - No leaksFirmware 3.46Bios 30.00Unit all okNew leak sensor fitted

This item has just arrived in our stock. Please enquire for further details.

This LDC Analytical HPLC Membrane Degasser was removed from a university lab where it was surplus to (more) requirements. The unit powers up but we were unable to test it further at our facility. It is in reasonable cosmetic condition with some marks and stains.

System contains: Solvent tray Vacuum degasser Binary pump Autosampler Thermostatted colomn compartme (more)nt Variable wavelength detector Vacuum degasser: The Agilent 1100 HPLC Degasser features a 4-channel vacuum container, including four tubular plastic membranes, and a vacuum pump. This degasser has a maximum flow rate of 0-10ml/min flow rate per channel and 5-10ml/min at reduced degassing performance. Binary pump: Flow Precision: <0.3 % RSD (typically <0.15 % RSD) Flow Range: Setpoints from 0.001 to 5.0 ml/min,  in 0.001 ml/min increments Operating range: 0 – 40 MPa (0 – 400 bar, 0 – 5880 psi) Pulsation: <2 % amplitude (typically <1 %) at 1 ml/min isopropanol at all pressures >1 MPa (> 10 bar, >147 psi) Compressibility compensation: User selectable, based on mobile phase compressibility Delay volume: 180 – 480 µl (600-900 µl with mixer) dependent on back pressure Recommended pH range: 1.0 – 12.5. Solvents with pH <2.3 should not contain acids which attack steel Well-plate autosampler: Safety features: Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display Injection range: 0.01 – 8 µl in 0.01 µl increments Precision: Typically < 0.5 % RSD of peak areas from 5 – 40 µl, Typically < 1 % RSD from 1 – 5 µl, Typically < 3 % RSD from 0.2 – 1 µl Sample viscosity range: 0.2 – 5 cp Sample capacity: 2 × well-plates (MTP) + 10 × 2 ml vials, 100 x 2 ml in one tray, 40 x 2 ml in half tray Injection cycle time: Typically < 30 s using following standard conditions: Default draw speed: 4 µl/min, Default eject speed: 10 µl/min, Injection volume: 0.1 µl Carry-over: Typically < 0.05 % using the following conditions: Column: 150 x 0.5 mm Hypersil ODS, 3 µm Mobile phase: Water/Acetonitrile = 85/15 Column Flow rate: 13 µl/min Injection volume: 1 µl caffeine (=25ng caffeine), 1 µl water to test carryover. Outside wash of needle before injection: 20 sec with water using flush port Thermostatted colomn compartment: Temperature range: 10 degrees below ambient to 80 °C, up to 80 °C: flow rates up to 5 ml/min Temperature stability: ± 0.15 °C Temperature accuracy: ± 0.8 °C (± 0.5 °C With calibration) Column capacity: Three 30 cm Warm-up/cool-down time: 5 minutes from ambient to 40 °C, 10 minutes from 40 – 20 °C Dead volume: 3 µl  Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN via other series module Safety and maintenance: Extensive diagnostics, error detection and display (through control module and Agilent ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Variable wavelength detector: Detection type: Double beam photometer Light source: Deuterium lamp Wavelength range: 190 – 600 nm Wavelength accuracy: ± 1 nm Bandwidth: 6.5 nm Linearity:> 2AU (5%) upper limit Flow cell standard: 14 µl volume, 10 mm cell path length, 40 bar

The GE AKTA Purifier 10 FPLC System is versatile, modular liquid chromatography systems for fast and (more) reliable separations of proteins, peptides, and nucleic acids by FPLC. AKTA Purifier 10 is designed for purification of microgram to milligram quantities of protein, operating at flow rates of 0.001 to 10 ml/min at pressures of 0 to 25 MPa. Flow Rate Range: Isocratic mode: 0.01 to 100 ml/min in steps of 10 µl/min Gradient mode: 0.01 to 100 ml/min in steps of 10 µl/min Double mode: 0.01 to 200 ml/min in steps of 10 µl/min Pressure Range: 0 to 10 MPa (100 bar, 1450 psi) pH Stability Range: 1 to 13 (1 to 14 with <1 day exposure) Viscosity: Max 5 cP Flow Rate Accuracy (0.2 – 10 MPa): ± 2% or 20 µl/min, whichever is greater Flow Rate Reproducibility (flow rate ≥ 0.5 ml/min): rsd < 0.5% Gradient Composition Accuracy: < ±1% at 0.5 to 100 ml/min Gradient Composition Reproducibility: rsd < 0.25% at 0.5 to 100 ml/min Pressure Sensor Range: 0 to 27.5 MPa Offset error: < 0.05 MPa Scale error: < ±2% Total Volume Between Inlet and Outlet: < 800 µl/module Wavelength range: 190 – 700 nm in steps of 1nm, 3 wavelenghts simultaneously Bandwidth: 4 nm Wavelength accuracy: ±2 nm Wavelength reproducibility: ±0.01 nm Wavelength switch time: < 500 ms (one cycle from 214 nm to 254 nm and back to 214 nm) Linearity: <2 % deviation up to 2 AU at 260 nm with Uracil at pH 2 Noise: Single wavelength (short term, 0.5 – 1 min): <6×10⁻⁵ AU at 230 nm Single wavelength (long therm, 1 – 10 min): <6×10⁻⁵ AU at 230 nm Dual wavelength (short term, 0.5 – 1 min): <2×10⁻⁴ AU at 230 nm and 254 nm Dual wavelength (long therm, 1 – 10 min): <2×10⁻⁴ AU at 230 nm and 254 mm Drift: <2×10⁻⁴ AU at 254 mm System consists of: UPC-900 monitor P-900 pump P-960 pump 2x INV-907 valve 2x PV-908 valve FRAC-950 fraction collector PC

Perkin Elmer LS 55 Luminescence Spectrometer This was removed from a university lab where it was sur (more)plus to requirements. The unit powers up and is in good cosmetic condition with marks from use. The lab reported that it was in good working order prior to removal, but we were unable to test it further at our facility.

Tuttnauer 3850ELP-D Lab Line Benchtop Autoclave Features - Take Advantage of Tuttnauer’s state-of-th (more)e-art advanced control system with multi-color display - Intuitive Multi-color display for easier reading gives quick access to important information. Color is used to indicate the stage of the cycle - Safe Automatic pressure locking system. Door will not open when the chamber is over pressured - 316 Ti grade high quality stainless steel chamber and door with electro-polish finish - Connect to a local network for use with RPCR Software for remote monitoring of up to 8 autoclaves - The 3850EL-D autoclave comes with 8 factory set cycle programs that cover the diverse processing needs of most laboratories and research centers - internal printer allows for the printing of Documents date, time, temperature and pressure Advanced multi-color control panel features intuitive method readouts in a multitude of languages. 316 Ti grade high quality stainless steel chamber and door with electro-polish finish allows for long product life and ease of periodic cleaning Designed to save space on your laboratory workbench, the 3850ELP-D is a front loading benchtop autoclave that provides high quality, repeatable performance and accountability for a wide range of applications used in modern laboratories. Each model has a number of optional added-value features which can be configured for fast cooling, efficient drying, biohazard and waste sterilization, Fo control, and more. The 3850ELP-D autoclave comes with 8 factory set cycle programs that cover the processing needs of most laboratories and research centers. This model features a printer.INCLUDED: The Tuttnauer 3850ELP-D Lab Line Benchtop Autoclave includes: - Power Cord - Operator's Guide - 3 Year Manufacturer's Warranty

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

The HX7.4P2 C is a powder coated beam scale equipped with the PUE HX7 indicator. This 4-load-cell me (more)chanical design can be used in a wider range of applications when compared to the standard pallet solutions. Beam spacing allows to place any loads onto the scale using either a forklift or a transporter crane. Transport-supporting handles facilitate transfer of the device to the place of use. The indicator has been outfitted with a colour 7&quot; graphic display and a diode bar graph which via red and green lights presents the current load mass referred to the scale range or preset minimum and maximum thresholds. At the back of the housing there are hermetic connectors of RS232, RS485, USB and Ethernet communication interfaces, plus digital inputs/outputs and analogue output. This enables cooperation with external devices such as barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. With use of the bracket you can either place the indicator at any flat horizontal surface, or fix it to the wall adjusting the tilt respectively to suit your needs. The terminal&#39;s software allows carrying out processes such as weighing, parts counting, dosing, labelling, formulations and percent weighing. Indicator&rsquo;s system of information is based on databases (users, products, weighings, packaging, formulations, customers) and ALIBI memory which guarantees stored data safety.