Agilent 1100 HPLC System

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Gilson HPLC System & Accessories - 306 - 811B - 805 - 832 - 7955- 119 - 506C This was removed fr (more)om a university lab where it was surplus to requirements. This is a large system. Most of the units have been powered up but it has not been tested further. We anticipate it may take some level or refurbishment to get it back to full working order. Included are; 1x Gilson XL Sampling injector:Model 231 The unit powers on and is in good cosmetic condition 2x Gilson Piston Pumps:Model 306 The units both power on and are in good cosmetic condition. 1x 15 pin MALE to FEMALE Ribbon cable:The unit is in good cosmetic condition. 1x Gilson Manometric Module:Model 805 The unit is in good cosmetic condition.There was no power port on the unit, it must be powered by a controller cable connected via a 306 Pump. 1x Gilson Dynamic Mixer:Model 811B The unit powers on and is in good cosmetic condition. 1x Gilson Temperature Regulator:Model 832 • Version 1.01The unit powers on and is in good cosmetic condition. 1x Gilson Collum Chiller:Model 7955 The unit powers on and is in reasonable cosmetic condition. 1x Gilson UV/VIS Detector:Model 119 •Version 2.01 The unit powers on and is in good cosmetic condition. 1x Gilson 506C System Interface unit:The unit is in good cosmetic condition. No sign of power. 1x 25 pin MALE to FEMALE serial cable for the (Gilson 506C System Interface unit)The unit is in good cosmetic condition. 1x 25pin Male to 9pin FEMALE connector adaptor.The unit is in good cosmetic condition. 1x Gilson Dilutor:Model 401 The unit powers on and is in good cosmetic condition. 1x Decade Electrochemical Amperometric Detector: ANTEC LeydenVersion 3.02The unit powers on and is in good cosmetic condition. 1x Viglen Contender PC:Model C3000A *OSWindows 98 •SoftwareUniPoint LC Version 3.01 The unit powers on. Accessories: 1x Viglen MonitorModel TS700 The unit powers on and is in good cosmetic condition. 1x Viglen KeyboardModel KB-0325 •PS/2 connector The unit is in good working and cosmetic condition  1x Microsoft Mouse:FCC ID: c3kkmp1 •PS/2 connector 1x VGA Cable:The unit is in good working and cosmetic condition. CD:1x Gilson UNIPOINT for Windows 98Version 3.0 Floppy Disk:Gilson System Software: •Version 1.71 •Disks 1 - 4Ser no. 219H8B765The units are in good cosmetic condition. •Win32s Disks 1-2The units are in good cosmetic condition. 2x Gilson 10WSC heads (cases)Ref E50056 • 3x Gilson WSC Pistion Pump Head user guides are inside the cases. 1x Gilson Thermostatic Rack Unit:Ser no. 270J1G048 The unit powers on via the (Gilson 832 temperature regulator)the unit is in good cosmetic condition. Gilson Racks for the thermostatic unit. 1x Rack Well, 60x 2ml glass or plastic vials.Part no 30 1x Rack Well, 108 x 0.7ml glass or plastic vials.Part no 31 The units are in good cosmetic condition. 1x Gilson Serial Input/Output Channel: 5 sets of( 2x FEMALE to 1x MALE 9pin connectors) Manuals:1x Unipoint system software: (Folder)The manual is in good condition and appears to be complete. 1x Gilson 506C System Interface User Guide:The manual is in good condition and appears to be complete. 1x Gilson 401 Dilutor Instruction manual:The manual is in good condition and appears to be complete. 2x Gilson 231-401 Auto Sampling Injector Instruction manual:The manuals are in good condition and appear to be complete. 1x Gilson 119 uv/VIS Detector User Guide:The manual is in good condition and appears to be complete. 1x 802C. 803C, 804C Manometric Module Instruction manual:The manual is in good condition and appears to be complete. 2x Gilson 306 Piston Pump User Guide:The manuals are in good condition and appear to be complete. 3x Gilson WSC Pistion Pump Head User Guides:The manuals are in good condition and appear to be complete. 1x Gilson UNIPOINT for Windows 98 User Guide:The manual is in good condition and appears to be complete. 2x 1x Decade Electrochemical Amperometric Detector Manuals:The manuals are in good condition and appear to be complete. 1x Gilson 832 Temperature Regulator User Guide:The manual is in good condition and appears to be complete. 1x Gilson 811B Dynamic Mixer User Guide:The manual is in good condition and appears to be complete. 1x Gilson 805-806-807 Manometric Modules User Guide:The manual is in good condition and appears to be complete. 1x Gilson SC- type Piston pump head Instruction manual:The manual is in good condition and appears to be complete. 1x Gilson 506C System Interface User Guide:The manual is in good condition and appears to be complete. 1x Gilson 506 Contact/ Modem Operators Guide:The manual is in good condition and appears to be complete. Syringes: 2x Phenomenex HPLC Columns:Model SYNERGI 4U Hydro- RP 80A 1x •Size 250x4.60mm1x •Size 250x3.00mm The units are in good cosmetic condition. 1x Phenomenex HPLC Column:Model SYNERGI 4U Polar - RP 80A •Size 250x4.60mm The unit is in good cosmetic condition. 1x Phenomenex HPLC Columns:Model HyperClone 5u ODS (C18) 120A •Size 250x4.60mm The unit is in good cosmetic condition. 1x Phenomenex HPLC Columns:Model HyperClone 5u SILICA 120A •Size 250x4.60mm The unit is in good cosmetic condition. 1x Phenomenex HPLC Columns:Model Phenosphere - NEXT 5u C18 •Size 250x4.60mm The unit is in good cosmetic condition. 2x HYPERSIL (5u ODS) Syringes:Prod no. 30105-062 •Size 150x4.60mm The units are in good cosmetic condition. 1x HYPERSIL (5u HyPURITY) Syringe:Prod no. 21005-022 •Size 150x4.60mm The unit is in good cosmetic condition. 2x HYPERSIL (ELITE C18 5u) Syringes:Prod no. 30105-062 •Size 150x4.60mm The units are in good cosmetic condition. 2x Phenomenex SYNERGI 4u Hydro -RP 80A Syringes:Part no. 00G-4375-E0 •Size 250x4.60mm The units are in good cosmetic condition. 1x Phenomenex HYPERSIL 3u C18 (ODS) Syringe: •Size 100x2.00mm The unit is in good cosmetic condition. 1x Phenomenex HYPERSIL 4u MAX -R P 80A Syringe: •Size 150x4.60mm The unit is in good cosmetic condition. 1x Phenomenex LUNA 3u c18(2) 100A Syringe: •Size 100x2.00mm The unit is in good cosmetic condition. 2x HYPERSIL 3 C18 Syringes: •Size 100x4.60mm The units are in good cosmetic condition. 1x Phenomenex BIOSep- SEC-S 200 Syringe: •Size 300x7.80mm The unit is in good cosmetic condition. 1x Phenomenex JUPITER 5u C18 300A Syringe: •Size 150x4.60mm The unit is in good cosmetic condition. 1x Hamilton Microliter Syringe:Model no. 1802RSNE •25uL The unit is in good cosmetic condition. 1x Hamilton Microliter Syringe:Model no. 1801RSNE •10uL The unit is in good cosmetic condition. 1x Hamilton Microliter Syringe:Model no. 801RNE WAT •10uL The unit is in good cosmetic condition.

AZURA preparative HPLC pump P 2.1L covers wide flow rate range and pressure capabilities. It has bee (more)n designed for purification of mg and gram samples. The Mobile Control allows intuitive control in stand-alone operation. The integrated automatic recognition of the pump head with RFID technology allows fast adaptions of the pump for various applications. Preparative pump offers wide range of flow rates (0.1-1000 ml/min) Choice of different LC software platforms Improved electronic drive compensation Integrated compressibility compensation Integrated leak management Constant pressure operation mode Solvent delivery Pump type: Preparative HPLC pump Delivery system: double piston pump with Al²O³ pistons Pump head: 250 ml/min Pump head materials: titanium Pressure sensor materials: PEEK (Polyether ether ketone) Maximum delivery pressure: 22.5 MPa (225 bar, 3260 psi) up to 100 ml/min, 20 MPa (200 bar, 2900 psi) at 250 ml/min Flow rate range: 0.1-250 ml/min, 0.5-200 ml/min (recommended) Flow rate increment: 0.01 ml/min Flow rate accuracy: ± 2 %, measured at 5 – 50 % of flow range using ethanol/water 10:90 Flow rate precision: < 0.2 % RSD Gradient support: isocratic, upgradeable to a binary HPG system with additionalpump P 2.1L or to a binary orternary LPG system HPG: gradient accuracy: ± 2 % (5 – 95 %, measured at 5 – 50 % of flow range, water/caffeine tracer) HPG: gradient precision: 1 % RSD, based on retention time at constant room temperature LPG: gradient accuracy:  ± 3 % (5 – 95 %, measured at 5 – 50 % of the flow range, water/caffeine tracer) LPG: gradient precision: 2 % RSD, based on retention time at constant room System protection: soft start, Pmin and Pmax are programmable Wetted materials: titanium,stainless steel, graphite fiber reinforced PTFE, FKM, PEEK, sapphire, aluminum oxide (Al²O³) Ambient conditions: temperature range: 10–40 °C; 50–104 °F, air humidity: below 90 % humidity (non condensing) Leak sensor: Yes Communication Control: LAN; RS-232; analog and event controlled Analog inputs: 0-10 V Analog control input: flow rate Level/event outputs: 8 event outputs (TTL, OC, relays) Programming: 19 programs + 9 links (to programs) + 1 wake up program Special features: system pump head is detected automatically using radio frequency identification (RFID) General Power supply: voltage range: 100 – 240 V, 50 – 60 Hz Dimensions: 361 x 208.2 x 523 mm (W x H x D) Weight: 19 kg

HPLC Waters 600 system. Includes a Waters Delta 600 multi-solvent quaternary pump, CPG column, a Wat (more)ers photodiode array detector (PDA) 2996, a Waters 600 controller, a Waters 717 autosampler, a PC with a PCI card and Empower software 3. Pump head volume of 225 μL at a flow rate of 45 ml / min or a pump head volume of 100 μL at a flow rate of 20 μl. ml / min It has an operating flow range of 0.01 to 45.0 mL / min, adjustable in increments of 0.01 mL / min.

The GE AKTA Purifier 10 FPLC System is versatile, modular liquid chromatography systems for fast and (more) reliable separations of proteins, peptides, and nucleic acids by FPLC. AKTA Purifier 10 is designed for purification of microgram to milligram quantities of protein, operating at flow rates of 0.001 to 10 ml/min at pressures of 0 to 25 MPa. Flow Rate Range: Isocratic mode: 0.01 to 100 ml/min in steps of 10 µl/min Gradient mode: 0.01 to 100 ml/min in steps of 10 µl/min Double mode: 0.01 to 200 ml/min in steps of 10 µl/min Pressure Range: 0 to 10 MPa (100 bar, 1450 psi) pH Stability Range: 1 to 13 (1 to 14 with <1 day exposure) Viscosity: Max 5 cP Flow Rate Accuracy (0.2 – 10 MPa): ± 2% or 20 µl/min, whichever is greater Flow Rate Reproducibility (flow rate ≥ 0.5 ml/min): rsd < 0.5% Gradient Composition Accuracy: < ±1% at 0.5 to 100 ml/min Gradient Composition Reproducibility: rsd < 0.25% at 0.5 to 100 ml/min Pressure Sensor Range: 0 to 27.5 MPa Offset error: < 0.05 MPa Scale error: < ±2% Total Volume Between Inlet and Outlet: < 800 µl/module Wavelength range: 190 – 700 nm in steps of 1nm, 3 wavelenghts simultaneously Bandwidth: 4 nm Wavelength accuracy: ±2 nm Wavelength reproducibility: ±0.01 nm Wavelength switch time: < 500 ms (one cycle from 214 nm to 254 nm and back to 214 nm) Linearity: <2 % deviation up to 2 AU at 260 nm with Uracil at pH 2 Noise: Single wavelength (short term, 0.5 – 1 min): <6×10⁻⁵ AU at 230 nm Single wavelength (long therm, 1 – 10 min): <6×10⁻⁵ AU at 230 nm Dual wavelength (short term, 0.5 – 1 min): <2×10⁻⁴ AU at 230 nm and 254 nm Dual wavelength (long therm, 1 – 10 min): <2×10⁻⁴ AU at 230 nm and 254 mm Drift: <2×10⁻⁴ AU at 254 mm System consists of: UPC-900 monitor P-900 pump P-960 pump 2x INV-907 valve 2x PV-908 valve FRAC-950 fraction collector PC

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

IKA RV 8 Flex Rotary Evaporator Speed Range 5 to 300 RPM Temperature Range Ambient to 180°C Maximu (more)m Flask Size 4L Features - New: 4 l heating bath - Integrated safety lift-out function in case of power failure - Package includes Woulff bottle - Water/oil heating bath with carrying handles - Locking button for fixing heating bath temperature - Clearly legible, glass-covered, black-and-white display panel - Locking mechanism: red indicator shows unlocked position of the vapor tube - Manual lift for precise positioning of the glassware - Adjustable immersion angle - Single-handed manual lift handling, suitable for left and right-handed operators - Speed range: 5 - 300 min-1 - Low device voltage (24V) ensures user safety - Flask clamping mechanism with integrated push-off function for easy exchange of evaporation flasks - High-efficiency condenser with 1500 cm² cooling surface - low space requirements - Compatible with the entire range of IKA RV 8 glassware The RV 8 Rotary Evaporator is the manual basic model in the family of IKA Rotation Evaporators. It finds a multitude of uses in the chemical, pharmaceutical, and biotechnology industries, in research and development, in manufacturing and quality assurance, in laboratories, and in plant construction. Digital displays for speed and heating bath temperature enable optimum control of all distillation processes. INCLUDED The IKA RV 8 Flex Rotary Evaporator includes: - RV 8 S099 - HB digital S099 Heating Bath - RV 05.10 Balljoint clamp - RV 10.73 Vapor tube (NS 24/40) - RV 10.8001 Seal - RV 3.4 Woulff bottle - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer Warranty (+ Additional Free 3 Year Warranty Extension with IKA Registration) IKA RV 8 Flex Rotary Evaporator SpecificationsType of coolingverticalCooling surface1500 cm2Motor principleDCSpeed range5 - 300 rpmSpeed tolerance set rotation speed &lt; 100rpm1 ±rpmSpeed tolerance set rotation speed 100rpm1 ±%LiftmanualStroke120 mmHeating temperature rangeroom temp. - 180 °CHeat output1400 WSet temperature resolution 1 ±KFilling volume max. 4 lDimensions (W x H x D)510 x 490 x 345 mmWeight22.366 kgPermissible ambient temperature5 - 40 °CPermissible relative humidity80 %Protection class according to DIN EN 60529IP 20Voltage100 - 240 VFrequency50/60 HzPower input1500 WDC Voltage24 VComparison of ModelsSpecificationIKA RV 10 Auto Pro FlexIKA RV 10 Digital FlexIKA RV 3 FlexIKA RV 8 FlexType of CoolingWithout CondenserVerticalN/AVerticalCooling Surface1500 cm²0 cm²N/A1500 cm²Speed Range5 - 300 rpm5 - 280 rpm20 - 300 rpm5 - 300 rpmLiftMotorMotorManualManualStroke140 mm140 mm150 mm120 mmHeating Temperature RangeRoom Temp. - 180 °CRoom Temp. - 180 °CRoom Temp. - 99 °CRoom Temp. - 180 °CTimerYesYesN/AN/ADimensions (W x H x D)500 x 430 x 440 mm500 x 430 x 440 mm440 x 530 x 330 mm510 x 490 x 345 mmWeight18.6 kg18.5 kg12 kg22.366 kgRS 232 InterfaceYesYesN/AN/AUSB InterfaceYesYesN/AN/AVoltage100 - 240 V220 - 240 / 115 / 100 - 240 / 100 - 120 / 100 - 115 V100 - 240 V100 - 240 V.comparison-table tr td:nth-child(5) { background-color: #fffacd; }Request a Formal Quote

The Memmert BE 400 is ideally suited for all applications with temperatures up to 70°C in research,  (more)medicine, pharmacy and food analysis, as well as food chemistry. It is especially useful for incubating live cultures at 37°C. The incubator is equipped with manually regulated air flow. Temperature range: Ambient temperature +5°C to 70°C Capacity: 40 L Internal glass door for observation Convection: natural Dimensions (WxDxH): 555 x 515 x 675 mm Internal dimensions (WxDxH): 380 x 285 x 385 mm Weight: 54 kg