Bio-Rad PowerPac Basic Power Supply

Destainer power supply DPS

VG Micromass Programmed Power Supply  Model - M18A w/  M426 Analogue Ratio Unit These unit (more)s were removed from another system. VG Micromass Programmed Power SupplyModel - M18ASN - 1403-13We were unable to plug this in to test. It requires an adapter that we do not have. VG Micromass Analogue Ratio UnitModel - M426SN - 1421-02Powers on

Genapta Laser Enable and Disbale Units & Single Photon Counting Box This system was removed from (more) a university lab where it was surplus to requirements. All the units power on but we were unable to test any further. They are in a reasonable used cosmetic condition with marks from use.

Zeiss Axioskop Microscope w/ J04Z0H Power Supply Lab This item was removed from a university where i (more)t was surplus to requirement. Both the microscope and power supply are in good cosmetic condition and full working order. The previous client has stated that this microscope was in full working order when it was last used. It has been tested with an in-house objective, which is not included. Includes the following: 1 x Zeiss Axioskop Microscope-2 x Zeiss PL 10 X/ 20 Eyepiece 1 x Zeiss J04Z0H Power Supply 1 x Zeiss 12V 100W Halogen HAL Lamphouse

Leica Diavert Inverted Microscope w/ 4 x Objectives & 465 Power Supply This was removed from a u (more)niversity lab where it was surplus to requirements. The unit is in reasonably good cosmetic condition. There are some light tape marks from general use, as well as some patina from age. It is in good working order. Included are; 1 x Leitz Phaco A 0.25 L62 Lamp 2x Eyepieces:PERIPLAN GF 12.5x /20 M lietz Wetzlar Germany 4x Leitz Wetzlar Objectives: 1x 170/- 4/0.121x 170/- L32/0.4 Phaco 11x 170/- L20/0.32 Phaco 11x 170/- 10/0.25 Phaco Power Supply:Model. 465

The certified intrinsically safe PM01.EX power supply, manufactured by RADWAG, has been designed to  (more)power the HX5.EX indicator. PM01.EX power supply comes in two designs: PM01.EX-1: power supply intended for operation in hazardous area: Zone 1 and 2, where there is a risk of explosion due to mixture of air with vapour, mist or gas, classified as explosion group IIC, IIB and IIA and as temperature class T1, T2, T3, T4. Zone 21 and 22, where there is a risk of explosion due to mixture of air with dust, flammable fibres and volatile fuels, classified as explosion group IIIC, IIIB and IIIA. PM01.EX-2: power supply intended for operation outside hazardous area, equipped with intrinsically safe circuits that can be placed in: Zone 1 and 2, where there is a risk of explosion due to mixture of air with vapour, mist or gas, classified as explosion group IIC, IIB and IIA and as temperature class T1, T2, T3, T4. Zone 21 and 22, where there is a risk of explosion due to mixture of air with dust, flammable fibres and volatile fuels, classified as explosion group IIIC, IIIB and IIIA. The certified intrinsically safe PM02.EX power supply, manufactured by RADWAG, has been designed to power the HRP.EX. PM02.EX power supply comes in two designs: PM02.EX-1-2: power supply intended for operation in hazardous area: Zone 1 and 2, where there is a risk of explosion due to mixture of air with vapour, mist or gas, classified as explosion group IIC, IIB and IIA and as temperature class T1, T2, T3, T4. Zone 21 and 22, where there is a risk of explosion due to mixture of air with dust, flammable fibres and volatile fuels, classified as explosion group IIIC, IIIB and IIIA. PM02.EX-2-2: power supply intended for operation outside hazardous area, equipped with intrinsically safe circuits that can be placed in: Zone 1 and 2, where there is a risk of explosion due to mixture of air with vapour, mist or gas, classified as explosion group IIC, IIB and IIA and as temperature class T1, T2, T3, T4. Zone 21 and 22, where there is a risk of explosion due to mixture of air with dust, flammable fibres and volatile fuels, classified as explosion group IIIC, IIIB and IIIA.

Do you need a moisture analyzer that not only determines moisture or dry matter content with impress (more)ive accuracy, but also performs a digital audit, responds to your voice commands and sends you light messages? If so, learn about the functionality of the ELLIPSIS series of moisture analyzers: It Dries in 4 Ways The MA 5Y.IC Moisture Analyzer offers you four drying profiles: standard, mild, fast and step. The standard profile is the usually used drying profile. It allows the most accurate determination of moisture content. The mild profile is designed for drying substances that are sensitive to the rapid heat released by the filaments, which heat full power at the initial stage of the process. An example of such a substance is leather. You will use the fast profile for samples with significant moisture content – of the order of even several tens of percent. The step profile will be ideal for drying substances that contain more than 15 percent moisture. Within this profile you can define any three temperatures. You will choose the values of temperature and duration of heating experimentally. What Drying Temperature Should I Set? The drying temperature determines the duration of the process. Its value depends on the type of material. If the temperature is too low, it will under-dry the sample and, consequently, unnecessarily increase the measurement time, while if it is too high, it will cause a burning effect on the material. The drying temperature for the traditional (oven) method is determined by industry or factory standards. If there are no standards, you will select the temperature experimentally. The maximum drying temperature on the MA 5Y.IC Moisture Analyzer is 160°C. How Do I Finish the Drying? In 4 Ways The MA 5Y.IC Moisture Analyzer has four finish modes: automatic, manual, time-defined and user-defined. Automatic mode You define the moisture loss limit value in 60 seconds. When the moisture analyzer reaches the set criterion, the measurement will automatically end. Manual mode You terminate the measurement yourself by pressing the STOP button. Time-defined mode The measurement ends after the set time has elapsed regardless of the result. You have up to 99 hours 59 minutes to manage! User-defined mode When you remove all volatiles from a sample, by definition, its mass should be constant. During drying, the dry mass of the sample is defined by a condition: if the mass of the sample is stable within 1 mg during the observation time (Auto 1-5), we consider that all volatile components have been removed from its structure. Digital Weighing Auditor Ensures that your moisture analyzer is ready for use. What is more, it informs about the need for a moisture analyzer inspection or a periodic audit of the moisture analyzer’s accuracy and sensitivity. 10-Inch Display Bigger screen – 10’’ – means more information in one place. On the new ELLIPSIS terminal, you will see up to 3 screens, widgets, graphs, statuses, notes, handy measurement history. Uncompromising User Verification For the first time ever, the moisture analyzer will verify the user using a password, RFID card, fingerprint reader, facial recognition mechanism, or any combination of these. Ambient Light – an Innovative Way for the Moisture Analyzer to Communicate With the User The light colour will tell you about status, process results, procedures, or alerts. Hotspot Use the moisture analyzer on any device connected to it. This can be a smartphone, tablet, or computer. RFID ELLIPSIS works with RFID tags* that can be used to tag your products or formulation ingredients in the database. They can also be used to identify a user. Live Note – Note Down Your Conclusions It’s the first time you can add a voice memo to a measurement series or procedure report. If you prefer to write it down, ELLIPSIS allows you to add a text note. Handy Library This is where a series of recent measurements or a report ready for digital signature, according to 21 CFR Part 11, can be found. Widgets Prepared to display what you need most at any given moment. 21 CFR Part 11 Do you work in the pharmaceutical industry? Do you need a digital signature? We are offering the moisture analyzer which as a standalone fully meets the requirements of 21 CFR Part 11/ EU GMP Annex 11. Full data security Electronic signatures Validations Electronic records Audit trails Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13.56 MHz

M1 Mass Standard - knob weights. Nominal value - 100 kg.

Crest Ultrasonics Mesh Basket for P500 Ultrasonic Cleaner The Crest Ultrasonics Mesh Basket for P500 (more) Ultrasonic Cleaner features a mesh size of 8 x 8mm and a wire thickness of1mm making this ideal for use inultrasonic cleaning.All baskets are equipped with drain handles, helping toprevent unnecessary carryover of the cleaning agent andkeeps your workplace clean. The Crest Ultrasonics Mesh Basket for P500 Ultrasonic Cleaner is 11.5" in length x 5.25" in width x 5" in depth and is for use with the P500 Ultrasonic Cleaners. The Crest Ultrasonics Mesh Basket for P500 Ultrasonic Cleaner is brand new in box . Includes a Full 1 Year Parts and Labor Warranty.

Benchmark MyFuge12 Mini Centrifuge Unlike traditional mini centrifuges, the new MyFuge 12 eliminates (more) the need to change rotors when switching between microtubes and PCR strips. The included, unique COMBI-Rotor is all that is required for running 12 microtubes and/or 4 PCR strips. With a fixed speed that produces 2,000 x g, this centrifuge is perfect for quick spin downs. Simply close the lid and the unit quickly ramps up to 5,500 rpm. Open the lid, and the rotor quickly decelerates for removal of samples. At just 5.5 inches wide and less than 4.5 inches tall, the MyFuge 12 truly is a personal microcentrifuge with unmatched capacity and flexibilty. INCLUDED: The Benchmark MyFuge12 Mini Centrifuge includes: - COMBI-Rotor - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty