Radwag AVK 1000.5Y.CP Automatic Constant Pressure Mass Comparator

The HRP 5Y.KO series of mass comparators enables calibrating mass standards and weights in accordanc (more)e with OIML Recommendation (R-111) for class F2 and lower classes. Comparators are used to ensure consistency in mass measurements as well as to verify weights according to legal metrology requirements. RADWAG mass comparators have been recognized by calibration laboratories in many countries. The HRP 5Y.KO mass comparators consist of two elements: a professional weighing platform (modern design of an electromagnetic mechanism in a hermetic steel casing) and 5Y terminal. The weighing platform is made of steel and features marks facilitating centric loading of mass standards. The comparator has a user-friendly menu. Data security and work results archiving are ensured by RADWAG terminal software.

The anti-draft chamber is an optional accessory intended for WAY KO mass comparators working in unfa (more)vourable conditions (air-drafts). It is mounted on a table, inside the mass comparator is placed. The chamber features sliding top and side panes allowing free access to the weighing chamber of the mass comparator. All components of the anti-draft chamber are made of metal and glass with conductive coating eliminating influence of electrostatics on the weighing result.

Powerbank ZR-04 is used for rechargeable power supply for balances and scale accessories. It uses fa (more)st charging technology. It allows long operating time without recharging and, thanks to the “Low Power” function, powering devices with low power consumption. The ZR-04 powerbank is made of high-quality components that ensure reliable operation. A display indicating the state of charge enhances ergonomics. Powerbank ZR-04 meets airline standards, which means that it can be carried on board an airplane as hand luggage. The device can simultaneously power the balance/ scale and charge the internal battery. The average power time of the balance/ scale is, depending on the product series, from 8 to as much as 24 hours.

The IM02.1 (MediaBox) communication module enables the expansion of the available range of interface (more)s of the PUE CY10 weighing terminal and 5Y series balances. It is equipped with RS 232, Virtual Com (USB type B) and 4 opto-isolated inputs and 4 semiconductor outputs, which enables interfacing PUE CY10 terminals and 5Y series balances with accessories such as: printers, control buttons (e.g. print-tar), light columns, buzzers, PLC controllers and other control and signalling devices. Assignment of input and output functions is possible from the menu of the PUE CY10 weighing terminal and 5Y series balances.

Mass comparators of UMA 5 series stand for the highest standard of professional automatic mass compa (more)rators. They provide comparison of 1 mg – 5 g weights of E1 and lower classes. The device is equipped with 36 magazine positions allowing to deposit up to 36 weights. This solution allows to perform either comparison for complete set of weights carried out within one process or comparison for just a few weights of the same mass. Owing to elimination of human factor and with temperature changes and air drafts reduced to zero, UMA automatic mass comparators provide the highest possible measurement repeatability.

The suspended self-centring weighing pan is designed specifically for the WAY 5Y.KO manual mass comp (more)arators. Installed It is installed during the device’s production stage in place of the standard weighing pan, so it should be ordered when ordering a comparator (it is not sold as a separate product). The weighing pan has the following functions: placing several weights, which are the resultant of the reference standard, off-centre, positioning the centre of gravity of the test and reference standards always in the same place.

Manufacturer: Beckman Coulter Model: J-26S XP BioSafe Three-Phase Description: The J-26S X sets the  (more)standard for performance, including high speed, low heat dissipation, imbalance tolerance and low noise level, and its wide range of separation capabilities is extended even further, now including three-phase filtration that further separates airlock material into solids, liquids and gases. The addition of a High Efficiency Particle Arrestance (HEPA) filter set makes the unit bio-safe. The J-26S XP centrifuge features a more impact-resistant lid, full containment barrier and automatic rotor detection. The ergonomic design - with lower unit height and hands-free door operation - remains unchanged. The J-265 XP can process six liters of fermentor output in less than 10 minutes, deliver a subcellular fraction at 82,000 x g, and run 24 microplates simultaneously. The unit automatically detects which rotor is installed and prevents the rotor from exceeding its maximum speed. It enables faster, quieter and more energy-efficient operation with better temperature control. The exclusive, high-torque SR (Switched Reluctance) drive reduces cycle times. Core features: - Processing six liters of digester output in less than 10 minutes. - Deliver a subcellular fraction at 82,000 x g - Run 24 microplates at once - Separate live cell populations with elutriation - Sterile filters prevent the escape of infectious material Specifications: Maximum speed: 26,000 rpm Acceleration: Maximum, slow or timed (1-10 minutes, 0-500 rpm). Deceleration: Maximum, Slow, Timed (1-10 minutes from 500-0 rpm) or Off Maximum capacity volume range: 1 - 6 L Refrigeration system: CFC-free, non-ozone depleting refrigerant Temperature range(s): 10°C - 40°C in 1 degree increments Weight: 290kg Dimensions (W x H x D): 71cm x 86cm x 86cm Power requirements: 220/380 VAC, 50 Hz, 3 phases Humidity restrictions:< 95% (non-condensing) Scope of delivery: - J-26S XP BioSafe Three-Phase without rotor - Instruction manual as PDF via e-mail If you need a suitable rotor, we are happy to help! The unit is in absolute top condition and has been 100% function tested.

This Randox RX Monza Automated Biochemistry Analysis System was removed from a university lab where  (more)it was surplus to requirements. The lab informed us that it was in full working order and had seen very little use. It has been powered up at our facility and is in excellent cosmetic condition. Accessories included:-Waste Bottle &amp; tubeCoagulation Testing Supplement (photocopy)Instructional DVDLamp (M925-002)RS232 Cable (M701-705)Thermal Paper Roll (M200-170)Small black part (M100-946)Pack of 0.4ml tubes (M800-099)

Stainless steel platform scale with four sensors No matter where you place the load on the platform, (more) the result will always be correct. This is due to the four sensors built into the platform. You will appreciate this especially when weighing an irregularly shaped object. It has been with us for years, and will stay for a long time to come The LCD display has accompanied us for long years. During this time it has proven its reliability. It guarantees the readability of the result from many angles and is energy efficient. Inner power No access to mains power? Power failure? No problem. Thanks to its internal rechargeable battery, the H315 scale works anyway (up to 7 hours). Power supply is available at an extra charge. As standard, the scale is equipped with a RS232 cable, to which you can connect most of the accessories from our range. Not just weighing But also parts counting, percent weighing, animal weighing and peak hold. The power of H315&rsquo;s working mods. Do you require fast and repeatable weight measurement under difficult conditions? The H315 scale is made for that! Work as you like The PUE H315 terminal sits on a 3-meter cable that allows you to hang the terminal on the wall. This allows you to arrange your weighing workplace in many ways. The power of steel The use of stainless steel guarantees you a long life for the scale. It is not afraid of contact with moist objects or accidental splashes. The membrane keyboard is another argument in the discussion of the water resistance of this scale. If you need a dual-range scale, we can make one for you at an extra cost.

Multifunctional scales TMX H is designed to fast and precise determination of mass in industrial con (more)ditions. TMX H Multifunctional scales TMX H comprises terminal PUE 5 and a weighing platform. Labelling system series TMX H is used to print labels for marking weighted goods e.g. in the process of packing. The program can generate standard labels for single goods. Functionality of the software: a function of weight control (weighing control + / -), previewing weighments carried out on weighing terminal as a table of weighments, simplified reporting module allowing the report to be generated, creation of label templates from labels in weighing terminal, identification of goods by using the code EAN-13 and EAN-128, quick search using the range of barcode scanner, the availability of databases: the operators, products, clients, warehouses, tares (packages), etc. The application enables measurements execution and their record into a local database or on the server. Networked terminals allow transmission of the measurements to the parent database installed on the server. The ability to work with a computer program E2R SYSTEM. Terminal types: PUE 5.15R, PUE 5.19R &ndash; resistive touch screen technology. Protection class IP68. High resistance to moisture and dust. In comparison to remaining models, limited brightness and lower resistance to shocks and scratches. Possibility of operation using gloves preventing scratches (latex, material). PUE 5.15IR, PUE 5.19IR &ndash; infrared touch screen technology. Protection class IP68. Very high brightness and readability level. High resistance to moisture and dust. High mechanical resistance, possibility of operation using gloves (made of latex, material or even steel chain). PUE 5.15C, PUE 5.19C &ndash; capacitive touch screen technology. Protection class IP68. High brightness and readability level. High resistance to moisture and dust, good mechanical resistance. Absolute precision of touch detection, sensing multiple points of touch (multi-touch).