AIRFLOW TA2-2 Thermisches Anemometer Thermometer 0-2 M/S 0-80°C Velocity

Sherwood M851 Air Compressor This item was removed from a university lab where it was surplus to req (more)uirements. The item is in good cosmetic condition, powers on, and is fully functional.

Woods 63KO Variable Pitch Aeronautical Engineering Wind Testing Tunnel This was removed from a univ (more)ersity engineering department where it was surplus to requirements. The tunnel was dismantled when we collected so no testing was carried out, but we were told that it was still in operational condition prior to dismantling. It is in five sections: Section 1- Main Power/ Fan Unit.-405 kg. 120 cm x 120 cm x 150 cm. Outlet flanges 63 cm inside diameter. 3 phase 5 pin 415V motor. Section 2- Silencer Unit- 160 kg. 127 cm x 91 cm x 131 cm. Flanges are 79 cm and 63 cm inside diameters. Section 3- Air Intake Funnel- 155 kg. 170 cm x 121 cm x 145 cm .Apertures are 41cm x 41 cm and 80 cm x 80 cm. Section 4- Large Tunnel Section-155 kg. 118 cm x 73 cm x 120 cm. Apertures are 41 cm x 41 cm and 64 cm diameter internal. Section 5- Work Access Unit-85 kg. 55 cm x 55 cm x 160 cm. This has 8 openings 30 cm x 60 cm. It comes with a variety of doors, 8 in total.

Ekom DK50 2VS 10bar Industrial Air Compressor with Enclosure This was removed from a university lab  (more)where it was surplus to requirements. The unit powers up and is in good working order. The lab confirmed it was working prior to removal.

Genlab LCI/9V/DIG Lab Incubator This was removed from a university lab where it was surplus to requi (more)rements. The unit powers up and is in good working order. (Digital thermometer not included). It is in good cosmetic condition with minor marks. 6 Shelves 50 x 50cm

This Bruker ImagePrep Sample Preparation Matrix Deposition Device was removed from a university lab  (more)where it was surplus to requirements. The unit is in good used cosmetic condition but it does have some marks and signs of use. It powers up fine and we have been through a few of the menus and they all work as they should. We were unable to test further as it requires a gas supply etc. We were told by the lab manager that it needed additional parts to make it operational, though we are unsure what exactly the fault is. It comes with a touch pen.

WEG CFW -11 Venture Inverter Control Box Lab This item was removed from a university where it was su (more)rplus to requirement. It is in good cosmetic condition, we are unable to power it on or test it further at our facility. The key is not included but can be opened with a standard control cabinet key. Includes manual. The unit has no cable so is sold for spares/repairs

The ramps are used to easily place the trolleys containing loads onto the 4-load-cell platform scale (more)s. They enable placing the scale into the production line as a measuring or control workstation. Uncomplicated loading and unloading of the weighing platform allows smooth control over the loads and is time saving.

If you buy a High Resolution Scale HY10 by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. Fast and Stable Measurement The scale displays the final result even in one second. High Maximum Capacity and Accuracy in a Single Device On the large weighing pan of an HRP scale, you can weigh a load of 150 kg with a readability of 1 g and impressive repeatability. Minimum Eccentricity Error Over the Entire Range On the HRP scales, you can also weigh irregularly shaped items with a centre of gravity significantly displaced from the weighing pan axis. Parameter Stability Over Time and After Transport Retain the correct metrological parameters even after prolonged, intensive use and transport of the scale due to its resistant and robust mechanical design. Weighing Pan Dimensions Adapted to the Accuracy of the Balance Weigh with the highest readability of 0.02 g on the 360 x 280 mm weighing pan and with a readability of 20 g on the 1,250 x 1,000 mm weighing pan. Maximum Robustness IP 67 platforms with additional sealing elements to protect against dust, dirt and moisture and can be cleaned with a pressure washer. New, lmproved MONOBLOCK® The new, taller and larger MONOBLOCK® enables the best repeatability and speed in its class of weighing platforms. New HRP Platform HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. Readability of 0.01 g at 10 kg maximum capacity and 0,2 g at 120 kg maximum capacity. Repeatability down to 0.01. Higher resistance to changes in ambient conditions. The platforms are so robust that they can be cleaned with a pressure washer. Transport protection that stiffens the structure during transport, eliminating any unwanted stresses. Platforms with a maximum capacity starting at 300 kg include transport handles, which makes them easy to move. Platforms of IP 67. PUE HY10 Terminal HY10 terminal is a constructional component of industrial multifunctional load cell scales, it connects with RADWAG high resolution platforms and weighing modules. High Level of Protection HRP scales have additional sealing elements to protect them from dust, dirt and moisture. This allows them to be cleaned with a pressure washer.

Labconco 9000620 WaterPro PS/HPLC Polishing Station, 115V, 60HzFeatures - Timed dispense for unatte (more)nded operation - Automatic/intermittent recirculation through polishing loop to maintain water quality, minimize bacterial growth and reduce rinse up time - Attractive and corrosion-resistant Type 304 stainless steel front panel - Unpigmented virgin natural polypropylene bowls have no impurities to contaminate water. - Water quality alert. LED flashes the actual megohm-cm when water quality falls below set point. - Built-in dispensing center - Quiet 1/4 hp motor and rotary vane recirculation pump - Dispensing valve - Wall mountable - TOC dump valve allows a small portion of purified water to drain during automatic recirculation to maintain low TOC levels (Analytical Instrument and Hybrid models). - UV flush valve allows a small portion of the purified water to rinse the ultrafilter during automatic recirculation to extend the life of the ultrafilter (Life Science and Hybrid models). - ETL listed (115 volt models) - CE Conformity (230 volt models WaterPro PS Polishing Stations deliver Type I, 18.2 megohm-cm water from the dispensing valve or optional dispensing gun at a typical rate of 1.8 liters per minute depending on feedwater flow rate and pressure, and installed purification modules.The control panel includes a timed dispense feature that allows unattended dispensing of pure water without risk of overfilling. The dispenser shuts off automatically once user-set time has elapsed. Labconco has designed WaterPro PS Stations with the right combinations of purification technologies to meet your needs. Choose from specialized stations for general chemistry, analytical, life science or combination usage. In addition, models designed for general chemistry may be upgraded with additional purification modules at a later time for use in analytical or life science applications.Click Here to View Product Video INCLUDED: The Labconco 9000620 WaterPro PS/HPLC Polishing Station, 115V, 60Hz includes: - Operator's Guide - Manufacturer's Documentation - 1 Year Manufacturer's Warranty