Metrohm LL Unitrode WOC 60259100

The ClonePix FL builds on the success of the Genetix white light ClonePix adding fluorescent imaging (more) capabilities for more intelligent selection. The unique proprietary technology behind ClonePix FL represents a major advance in cell line selection and development, significantly reducing the time and costs associated with new biopharmaceutical product development especially when compared to standard techniques such as limited dilution or cell sorting. Specification: White light imaging- Trans-illumination for imaging low contrast colonies such as adherent monolayers or small colonies in suspension. Epi-illumination for imaging colonies as they are collected Fluorescence imaging- Software-controlled switching between up to 5 excitation /emission filter pairs (we recommend no more than 3 filters be multiplexed for optimal performance) Data tracking- Internal barcode reader for source and destination plates enables data tracking for each run Camera- Integrated 16-bit cooled CCD camera Imaging speed- 6-well microplate: 5 min for 2 wavelengths (standard conditions) Resolution- Standard: 28 micron; Maximum: 1.5 micron Containment- Fully enclosed working environment with Class 100-type, HEPA filtration Source plate type- PetriWell-6 plate, PetriWell-1 plate, Greiner 6 well plate, Nunc 6 well plate, Nunc OmniTray Destination plate type- PetriWell-96 plate, Costar 96 well plate, Greiner 96 well plate, Nunc 96 well plate, Falcon 96 well plate Source plate capacity- 10 plates Destination plate capacity- 10 plates Picking head- 8 x picking pins – each pin independently controlled Picking pin size- Diameter of picking pins is application specific – F1: suspension cells, F2: adherent cells Picking speed > 200 clones per hour Wash bath- Ethanol wash bath, automatically refilled Picking system fluids- 5 L sterile water supply, 5L waste bottle Pin drying- Proprietary halogen pin drying station

Downflow velocity: 0.35 m/s Sound level: < 58 dBA Light intensity: > 800 lux Pre-filter (EN 779): G4 (more) Horizontal HEPA filter (EN 1822): H14 Dimensions (WxDxH): 1900 x 740 x 1360 mm Interior dimensions (WxDxH): 1800 x 600 x 685 mm Height with support frame: 2240 mm Aperture height (work mode/maximum): 165/375 mm Weight: 230 kg Filter check is ok, but has a stain.

COURAGE + KHAZAKA Cutometer MPA580 This was removed from a university lab where it was surplus to re (more)quirements. The unit did not power up in testing. It is sold for spares/repairs.

ISMATEC peristaltic pump drive motor type MC Motor only, without peristaltic head Type: MC ISMATEC S (more)A brand 40W 50Hz

Taylor Wharton CX500 Liquid Nitrogen Dewar This was removed from a university lab where it was surpl (more)us to requirements. The unit is in good cosmetic condition with minor marks but has not been tested.

This Nikon Microphot-FXA Fluorescence Microscope was removed from a university lab where it was surp (more)lus to requirements. The PSU is missing so we were unable to power up the Microscope. It requires a Nikon PSM-4A. The power supply unit for the mercury lamp is present. The PSU is working but the bulb needs to be replaced. The system is in reasonably good cosmetic condition with marks from use. It has; 2x Nikon FX-350X 35mm film cameras attached via Nikon mounts.1 x SOFT RTS 25.4 2mp slider with data lead. 1 x NIKON 4/0.101 x NIKON FLUOR 20 0.75 160/0.171 x NIKON FLUOR 40 0.85 160/0.11-0.231 x NIKON FLUOR 100 / 1.30 OIL 160/0.172 x CFWN D10 X/20 There is a PC with ISMOL Software &amp; relevant PCI cards for connecting everything.