Disperser OV 725 Digital System Velp

Sample preparation stirrer Modernize your laboratory with Guardian 5000 Series shakers, designed to  (more)be safe and deliver exceptional safety and superior performance. Numerous cutting-edge Ohaus features: - SafetyHeat system to protect the laboratory: an industry-leading sensing system uses two independent safety controls to continuously monitor the electronics and shut off the heat before it overheats - Powerful and consistent shaking performance: precise stirring from 60 to 1600 rpm is made possible by the design of a powerful, robust motor with magnet and software controlled ramp rate, ensuring safe stirring even for viscous applications. - Easy to read LCD display with everything you need to know: the bright LCD display includes temperature and speed settings, intuitive icons and hot top indicator - Durable and reliable with SmartHousing: smartHousing is resistant to chemicals with an innovative and easy to clean design; the lines allow any liquid spills to drain out of the instrument Available models: Model e-G51HP07C: plate 178x178mm; flow rate 15 litres; ceramic plate; heating up to 500°C. Model e-G51HS07C: plate 178 x 178mm; flow rate 15 litres; ceramic plate; heating up to 500°C and stirring up to 1600rpm. Model e-G51HS10C: plate 254x254mm; flow rate 18 litres; ceramic plate; heating up to 500°C and stirring up to 1600rpm. Model e-G51HSRDM: plate Ø135mm; flow rate 18 litres; aluminum plate; heating up to 380°C and stirring up to 1600rpm. Model e-G51ST07C: plate 178x178mm; flow rate 15 litres; ceramic plate; stirring up to 1600rpm. Applications Boiling water, water/oil bath preparation, sample and solution preparation, dissolution buffers and reagents, sample concentration Display Backlit LCD display for temperature and speed, green lights when unit is heating and agitating, prominent hot light, probe in use icon, single point calibration icon Operation Stirring from 60 to 1600 rpm, ambient temperature range from +5°C to 500°C (ceramic top) or 380°C (aluminum top), power cord (included), the stirring models include a 1.5” (3.8cm) PTFE coated stir bar Construction Probe connection, SmartHousing™ stays cool to the touch and is resistant to chemicals, IP21 rated, polycarbonate front panel, control knobs, On/Off switch to disconnect heater, integrated pole holder, easy-to-use ceramic or aluminum tops to clean Characteristics Hot top light, audible alarm, SafetyHeat™ protection shuts down heater in case of malfunction, temperature calibration function for 3 probes and 3 platen setpoints

The ClonePix FL builds on the success of the Genetix white light ClonePix adding fluorescent imaging (more) capabilities for more intelligent selection. The unique proprietary technology behind ClonePix FL represents a major advance in cell line selection and development, significantly reducing the time and costs associated with new biopharmaceutical product development especially when compared to standard techniques such as limited dilution or cell sorting. Specification: White light imaging- Trans-illumination for imaging low contrast colonies such as adherent monolayers or small colonies in suspension. Epi-illumination for imaging colonies as they are collected Fluorescence imaging- Software-controlled switching between up to 5 excitation /emission filter pairs (we recommend no more than 3 filters be multiplexed for optimal performance) Data tracking- Internal barcode reader for source and destination plates enables data tracking for each run Camera- Integrated 16-bit cooled CCD camera Imaging speed- 6-well microplate: 5 min for 2 wavelengths (standard conditions) Resolution- Standard: 28 micron; Maximum: 1.5 micron Containment- Fully enclosed working environment with Class 100-type, HEPA filtration Source plate type- PetriWell-6 plate, PetriWell-1 plate, Greiner 6 well plate, Nunc 6 well plate, Nunc OmniTray Destination plate type- PetriWell-96 plate, Costar 96 well plate, Greiner 96 well plate, Nunc 96 well plate, Falcon 96 well plate Source plate capacity- 10 plates Destination plate capacity- 10 plates Picking head- 8 x picking pins – each pin independently controlled Picking pin size- Diameter of picking pins is application specific – F1: suspension cells, F2: adherent cells Picking speed > 200 clones per hour Wash bath- Ethanol wash bath, automatically refilled Picking system fluids- 5 L sterile water supply, 5L waste bottle Pin drying- Proprietary halogen pin drying station

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Masticator lab blenders are used in homogenizations during microbiological testing in food, cosmetic (more) and pharmaceutical labs. The 400 ml Masticator blender is meant to homogenize 10 to 40 g (previously diluted) samples. 400 ml bags with and without filters can be used, the former allow to ensure pipetting of debris-free homogenized liquid and are particularly recommended when homogenizations yield sample suspensions with high amounts of large-sized particles.

The Model 400 Hybridization oven is a high precision rotating convection oven for Northern blot and  (more)Southern blot hybridizations and other applications.