Amersham Biosciences AKTA Pilot Liquid Chromatography System Lab

Agilent 1100 system consisting of: 1x Agilent 1100 Degasser type G1379A 2x Agilent 1100 Isocratic Pu (more)mp type G1310A 1x Agilent 1100 Variable Wavelength Detector type G1314A 1x Agilent 1100 Fluorescence Detector type G1321A 2x Solvent tray Manual injector with 1 ml sample loop Laptop Agilent 1100 IsoPump: Hydraulic system: Dual piston in series pump with proprietary servo-controlled variable stroke drive, floating pistons and active inlet valve Setable flow range: 0.001 – 10 ml/min, in 0.001 ml/min increments Flow range: 0.2 – 10.0 ml/min Flow precision: < 0.3 % RSD (typically 0.15 %), based on retention time, at 1 ml/min Pressure: Operating range 0 – 40 MPa (0 – 400 bar, 0 – 5880 psi) up to 5 ml/min, Operating range 0 – 20 MPa (0 – 200 bar, 0 – 2950 psi) up to 10 ml/min Pressure pulsation: < 2 %amplitude (typically < 1 %), at 1 ml/min isopropanol, at all pressures > 10 bar (147 psi) Compressibility compensation: User-selectable, based on mobile phase compressibility Recommended pH range: 1.0 – 12.5, solvents with pH > 2.3 should not contain acids which attack stainless steel Dimensions (HxWxD): 140 x 345 x 435 mm Weight: 11 kg Agilent 1100 VWD: Detection type: Double-beam photometer Light source: Deuterium lamp Wavelength range: 190–600 nm Short term noise (ASTM): ± 0.75 x 10-5 AU at 254 nm Drift: 3 x 10-4 AU/hr at 254 nm Linearity: > 2 AU (5%) upper limit Wavelength accuracy: ± 1 nm Self-calibration with deuterium lines, verification with holmium oxide filter Band width: 6.5 nm typical Flow cell: 14-µl volume, 10-mm cell path length and 40 bar (588 psi) pressure maximum Dimensions (HxWxD): 140 x 345 x 435 mm Weight: 11 kg Agilent 1100 FLD: Detection type: Multi-signal fluorescence detector with rapid on-line scanning capabilities and spectral data analysis Light source: Xenon flash lamp Pulse frequency: 296 Hz for single signal mode, 74 Hz for spectral mode Excitation monochromator: range; 200 – 700 nm and zero-order,  bandwith; 20 nm, monochromator; concave holographic grating F/1.6 blaze 300 nm Emission monochromator: range; 280 – 900 nm and zero-order,  bandwith; 20 nm, monochromator; concave holographic grating F/1.6 blaze 400 nm Spectrum acquisition: Excitaiotn or emmision spectra, scan  speed; 28 ms per data point, step size; 1 – 20 nm Wavelength characterisric: Repeatability; ±0.2 nm, accuracy; ±3 nm Flow cell: 8 µl volume and 20 bar pressure, quartz Dimensions (HxWxD): 135 x 345 x 435 mm Weight: 11.5 kg

AZURA preparative HPLC pump P 2.1L covers wide flow rate range and pressure capabilities. It has bee (more)n designed for purification of mg and gram samples. The Mobile Control allows intuitive control in stand-alone operation. The integrated automatic recognition of the pump head with RFID technology allows fast adaptions of the pump for various applications. Preparative pump offers wide range of flow rates (0.1-1000 ml/min) Choice of different LC software platforms Improved electronic drive compensation Integrated compressibility compensation Integrated leak management Constant pressure operation mode Solvent delivery Pump type: Preparative HPLC pump Delivery system: double piston pump with Al²O³ pistons Pump head: 250 ml/min Pump head materials: titanium Pressure sensor materials: PEEK (Polyether ether ketone) Maximum delivery pressure: 22.5 MPa (225 bar, 3260 psi) up to 100 ml/min, 20 MPa (200 bar, 2900 psi) at 250 ml/min Flow rate range: 0.1-250 ml/min, 0.5-200 ml/min (recommended) Flow rate increment: 0.01 ml/min Flow rate accuracy: ± 2 %, measured at 5 – 50 % of flow range using ethanol/water 10:90 Flow rate precision: < 0.2 % RSD Gradient support: isocratic, upgradeable to a binary HPG system with additionalpump P 2.1L or to a binary orternary LPG system HPG: gradient accuracy: ± 2 % (5 – 95 %, measured at 5 – 50 % of flow range, water/caffeine tracer) HPG: gradient precision: 1 % RSD, based on retention time at constant room temperature LPG: gradient accuracy:  ± 3 % (5 – 95 %, measured at 5 – 50 % of the flow range, water/caffeine tracer) LPG: gradient precision: 2 % RSD, based on retention time at constant room System protection: soft start, Pmin and Pmax are programmable Wetted materials: titanium,stainless steel, graphite fiber reinforced PTFE, FKM, PEEK, sapphire, aluminum oxide (Al²O³) Ambient conditions: temperature range: 10–40 °C; 50–104 °F, air humidity: below 90 % humidity (non condensing) Leak sensor: Yes Communication Control: LAN; RS-232; analog and event controlled Analog inputs: 0-10 V Analog control input: flow rate Level/event outputs: 8 event outputs (TTL, OC, relays) Programming: 19 programs + 9 links (to programs) + 1 wake up program Special features: system pump head is detected automatically using radio frequency identification (RFID) General Power supply: voltage range: 100 – 240 V, 50 – 60 Hz Dimensions: 361 x 208.2 x 523 mm (W x H x D) Weight: 19 kg

This system was removed from a university lab where it was surplus to requirements. All units power  (more)up but this has not been tested further as a system. It is in reasonably good cosmetic condition with marks from use. Included are; 1x Waters Pump Control Module IIModel: PC2S/N: K05PC2 650E 1x Waters Temperature Control Module IIModel: TC2S/N: H05TC2 641E 1x Waters 515 HPLC PumpModel: 515S/N: L05515 088A 1x Waters Column Fluidics OrganizerModel: APCS/N: K05APC 452M 1x Waters 2767 Sample ManagerModel: 2767 SAMPLE MGR.Part no: 725000299S/N: H05XY6 738MSample tubes fit 16ml vials. 1x Samsung MonitorModel:&nbsp;171S SS/N: GH17HJCTB07621N 1x AOC LCD MonitorModel: LM520 AS/N: T5GJ32AR05528 1x Fujitsu Siemens Mouse1x Acer Mouse1x Acer KB-0759 Keyboard1x BTC 5197 Keyboard 1x Applied Biosciences Programmable Absorbance DetectorModel: 785AS/N: 29511519 1x IBM ThinkCentre PCMT-M 8143-QGHS/N: LMPM2TKThe hard drive has been removed from the PC.We are certain it was paired up with Control Modules. 1x HP vw8400 WorkStationS/N: CZC7113H1HMassLynxMassLynx DiversitySirius Analytical Instruments 1x Waters Column Heater ModuleModel: CHMS/N: M05CHM174M 1x Waters Leak Sensor Module 1x Gilson 506C System Interface ModuleS/N: 369J8PA500 1x Waters Fraction Collector III Ver.W2.01Model: WFCS/N: D06WFC178J 1x Perkin Elmer Series 200 LC PumpS/N: 291N 5110302 1x S-Video Mini-DIN 4-pin1x RS-232C Serial Cable1x Control Cable Assembly1x SCSI I to SCSI II Cable1x Drive Cable 25 Pin male/male 1x Waters 2525 Binary Gradient Module Installation &amp; Maintenance Guide1x Waters 2767 Sample Manager Injector Installation &amp; Maintenance Guide1x Waters 515 HPLC Pump Operator's Guide1x Performance Maintenance Protocol 2007-20091x Waters Purification of Compounds - Using FractionLynx

This Agilent Technologies 1200 Series HPLC G1312B Binary Pump was removed from a university lab wher (more)e it was surplus to requirements. The item is in good cosmetic condition and powered up, as seen the item is missing the front door panel. We are unable to test this item further at our facility. Power supply included.

Waters Acquity UPLC H07UPT, H07UPA, H07UPB &amp; F07UPH System This item was removed from a univers (more)ity where it was surplus to requirement. All included units are in good cosmetic condition and power on independently, we are unable to test them further as a system at our facility. This system comprises the following: 1 x Waters Acquity TUV Detector- H07UPT1 x Waters Acquity Sample Manager- H07UPA1 x Waters Acquity Binary Solvent Manager-H07UPB1 x Waters Acquity Ethernet Box -F07UPH

Gilson MiniPuls 3 peristaltic pump Technical characteristics Voltage: 220-240V, 50/60Hz Power: 45VA  (more)Speed: 0-48 revolutions 8 channels Standard flow rate: 0.3 µL/min – 30 mL/min at maximum pressure 0.5 MPa Pump head speed: adjustable 0 to 48 rpm with increments 0.01 rpm to 9.99 rpm and increments 0.1 rpm to 10 rpm Standard model pipe diameter: 0.25–4 mm (ID) External dimensions (L) x (D) x (H): 15 x 17.5 x 29.5 cm

This job lot of items comes from a variety of university laboratories. The items were no longer requ (more)ired, collected from various store rooms and facilities. None of these items have been tested at our site - it is likely that some will be spares/repairs, but we anticipate that a reasonable amount should operate well. None of these items have been PAT or electrical safety tested. For this reason, we have marked these as spares/repairs as they should not be used without appropriate electrical safety checks. They are sold as a spares/repairs bundle intended to be purchased by someone who has time to test and where necessary refurbish the units. It is an excellent opportunity for anyone looking to benefit from individual equipment resale. The units have not been tested at all. Included are; 4 x ESI Nuclear scaler - timer - ratemeter 2454 x S&amp;J Juniper Standard hotplates with aluminium top plate4 x Farnell Proto-Board 203A solderless bread board2 x Bowens Espirit 500 professional photography lighting flash headElga Elgastat UHQPS water purification systemGenomic Solutions vacuum pump 6035A080Techne TC-3000 FTC3/02 thermal cyclerEriComp Power Block ll system easy cycler4 x Irwin Croydon Type J1 MKlll power supply unitsBayer DCA 2000+ analyserApplied Biosystems 2720 thermal cyclerLabnet Multigene gradient thermal cycler TC9600-G (locked)Thermo Hybaid SPRT001 Issue 2 PCR spring authorised thermcyclerNaiad Technologies DabOut system PN DO-C DO-LVS-CShimbo SMS-200B stroboscopeTechne Dri-Block DB-3A FDB03ADGrant Type QBT2 digital block heaterGrant 38L water bath with GD120 heater-stirrer2 x Grant Type JB1 heated waterbathSorvall TFT 70.38 70,000rpm fixed angle centrifuge rotor 8 x 25mm tubesMitsubishi P93E monochrome thermal printerOerlikon Leybold vacuum exhaust filter AF16LKB Bromma Model 11800 ultramicrotome system pyramitomeJob lot water baths, heater elements and pumps

Fusion UV DRSE 120 UV Coating System Lab This system was removed from a university where it was surp (more)lus to requirement. All units are in good cosmetic condition and powered on, however the Conveyor belt motor runs independently but not when connected to the main unit. The UV lights are not working and the power supply is showing error codes related to interlock and RF detector issues. Due to the faults stated above, this system is listed as Spares/Repair. This system comprises the following: - Fusion UV DRSE 120 UV Coating System - Fusion Systems Power Supply P150 - Fusion Systems Model I250B - Fusion Systems Blower K523/2 - 2 x Fusion UV Magnetron 554172 (New in Original Packaging) - Fusion UV Variable Power Supply

The scales is designed for weighing patients in health care facilities and in clinics. It is equippe (more)d with indicator PUE C315 series comprising a backlit LCD display and 5-button keyboard ensuring simple operation of scale basic functions. Personal scales is supplied either by mains or by batteries. The model without height-meter has an indicator attached to the weighing platform. It is manufactured as a dual range instrument.

IKA Eurostar 100 Control P4 Overhead Stirrer Speed Range 10 - 300 RPM Viscosity Max. 100,000 mPas  (more)Stirring Quantity Max. 100 l Features - Reverse function - Multilingual TFT display - Programmable functions - Integrated temperature measurement - Interval operation - Timer function - Adjustable safety circuit - Locked function - Infinitely adjustable speed - Push-through agitator shafts - Overload protection - Short-term overload operation - Quiet operation - Error code Display - H 67.60 temperature sensor and WH 11 WiCo holder included in delivery The extremely powerful laboratory stirrer EUROSTAR 100 control P4 with a removable wireless controller and a digital TFT display is especially suitable for highly viscous applications and provides a torque of up to 320 Ncm. It automatically adjusts the speed through microprocessor controlled technology within the speed range of 0/10 - 300 rpm. The stirrer comes equipped with a RS 232 and a USB interface to control and document all parameters. Furthermore, an integrated torque trend display is provided for the measurement of viscosity changes and its electronic safety circuit ensures automatic cut-off in an anti-stall or overload conditions. Continuous comparison of shaft speed to desired speed is maintained and variations are adjusted automatically. This guarantees a constant speed even with changes in viscosities of the sample.INCLUDED: The IKA Eurostar 100 Control P4 Overhead Stirrer includes: - EUROSTAR 100 control P4 - H 67.60 Temperature sensor, stainless steel - WH11 - OS 1.0 WiCo power supply unit - USB Cable - USB A to Micro-B, 2 m - USB cable micro A – micro B 2.0 - Screw driver - Protective cover for WiCo contact - Chuck key - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer Warranty ( + Additional Free 1 Year Warranty Extension with IKA Registration) IKA Eurostar 100 Control P4 Overhead Stirrer Specifications Stirring quantity max. per stirring position (H2O)100 lMotor rating input174 WMotor rating output142 WMotor principleBrushless DCSpeed displayTFTSpeed range10 - 300 rpmReversible direction of rotationyesIntermittent operationyesViscosity max.100000 mPasOutput max. at stirring shaft 100 WPermissible ON time 100 %Torque max. at stirring shaft 320 NcmSpeed controlsteplessSetting accuracy speed1 ±rpmDeviation of speed measurement n &lt; 300rpm3 ±rpmStirring element fasteningchuckConnection for ext. temperature sensorPT1000Temperature displayyesChuck range diameter0.5 - 10 mmFastening on standextension armExtension arm diameter16 mmExtension arm length220 mmTorque displayyesNominal torque3.20 NmTorque measurementtrendDeviation of torque measurement I30 ±NcmTimeryesTimer displayTFTTime setting range1 - 6000 minTemperature measuring range-10 - +350 °CTemperature measurement resolution0.1 KAccuracy of temperature measurement±0.5 + tolerance PT1000 (DIN EN 60751 Class A) KLimit deviation temperature sensor≤ ± (0.15 + 0.002xITI) KHousing materialalu-cast coating / thermoplastic polymerCommunication distance (depend onbuilding) max.150 mDimensions (W x H x D)86 x 352 x 230 mmWeight5.2 kgPermissible ambient temperature5 - 40 °CPermissible relative humidity80 %Protection class according to DIN EN 60529IP 40RS 232 interfaceyesUSB interfaceyesVoltage230 / 115 / 100 VFrequency50/60 HzPower input150 W DownloadsTechnical Specification Download Operator's Manual Download Request a Formal Quote

Benchmark Compact Anti Static Ionizer Static charge can accumulate on many types of samples as well  (more)as weighing containers, affecting mass determination on an analytical balance. The Benchmark Scientific W3130 Accuris Anti-Static Ionizer produces and emits negatively and positively charged ions that will neutralize static electricity on samples and containers. A blower can be turned on for rapid static discharge, or turned off for work with powders or light-weight materials. INCLUDED: The Benchmark Compact Anti Static Ionizer includes: - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty