200 Series Compact GC

Hewlett Packard HP 6890 GC Gas Chromatograph & Agilent 6890 Series Injector This was removed fro (more)m a university lab where it was surplus to requirements. The unit has had the mains power board removed and is sold for spares/repairs. It is in reasonably good cosmetic condition but has some marks from use.

Reason for return - Investigate faults and re-list accordingly: - We received the item with a cracke (more)d glass piece to the photoionization detector. We replaced it with a piece that was provided. - We piped the system with N2 carrier gas and gas lines carrying product to the inlet of the GC. We turned on the switch to the Photoionization detector, under high sensitivity, and can visibly see it turn on. The source is aligned. The detector is aligned.  - We programmed the event on the software to turn the valve of the 10-way valve accordingly to enable the carrier gas to bring the product through the GC. - We introduced acetone via the sample loop (inlet gas) - we saw no peaks. We introduced acetone via injection - we saw no peaks.  - I leaked checked the piping including within the detector - no issues. I checked the point of outlets to make sure flow is continuous too - no issues. - The mechanism of the valve turning - it made a cranky sound, and I am not convinced it is turning the valve.  - There may be two issues. I had figured it was the valve so I tried injecting acetone directly into the line, but we could not see any peak of acetone. (Issues with the detector?) I am not sure if the valve's squeaking/cranky sound implies it is turning but there might be an issue here too. This SRI 8610C GC Gas Chromatograph System was removed from a university lab where it was surplus to requirements. The unit powers up but we were unable to test it further at our facility. The lab did confirm however, that is in good working order. It is in very good cosmetic condition with only very minor marks from use.

Job Lot of Varian GC Systems Gas Chromatograph Spares or Repairs All items are in good cosmetic cond (more)ition with minimal wear This job lot of items comes from a university lab, The items were no longer required. None of these items have been tested at our site - it is likely that some will be spares / repairs, but we anticipate that a reasonable amount should operate well. None of these items have been PAT or electrical safety tested. For this reason we have marked these as spares/repairs as they should not be used without appropriate electrical safety checks. They are sold as a spares/repairs bundle and further investment in each individual product may be required. It is an excellent opportunity for anyone looking to benefit from individual equipment resale. The units have not been tested at all. This job lot includes the following: Varian CP-3800SN - 06822 Varian CP-3800SN - 105885 Varian CP-3800SN - 03297 Varian CP-3800SN - 05481 Varian CP-3800SN - 05482 Varian 3900SN - 00283 Varian Chrompack Micro GC CP - 2003PSN - 941039 Varian PN - 03-917569-10SN - 8487

Shimadzu GC-2014 Gas Chromatograph This item was removed from a university lab where it was surplus  (more)to requirements. It is in good cosmetic condition and powers on, but there is no software included.Therefore, we are unable to conduct further testing. The lab confirmed it was in working order prior to removal, but were unable to provide the PCs and Software. Includes:- Manual - Users manual on disc - LabSolutions GC Solution release 2.30 Specifications:- Model: GC-2014 - Serial No.: C11484301470

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Varian 660-IR FT-IR Spectrometer This item was removed from a university where it was surplus to req (more)uirement. It is in good cosmetic condition and powers on, it has been seen by an engineer with a summary of the report stated below. The beam splitters showing signs of moisture damage, and the unit has software recognition issues.As a result, it is listed as Spares/Repair.

VACUUBRAND VACUU-PURE 10C Screw Pump Ultimate Vacuum 0.005 mbar (0.0038 Torr) Maximum Pumping Speed (more) 5.3 CFM Inlet/Outlet Connection Small Flange KF DN 25 Features - 10-3 mbar vacuum range - 100% oil-free - Chemically resistant - No wear parts The dry screw pump VACUU-PURE® 10C reliably delivers the benefits of oil-free vacuum technology in the pressure range of 10-3 mbar. The new vacuum pump combines three important benefits for the user: 100% oil-free, chemically resistant, and no wear parts. VACUU-PURE 10C is ideally suited for clean processes and the production of pure products. The screw pump is especially designed for processes in the vacuum range down to 10-3 mbar, however unlike other fine vacuum technologies it can be used across the entire pressure range from atmospheric pressure to its ultimate vacuum. At the same time, aggressive gases and vapors can be pumped without any worries because of the high chemical resistance. The use of a cold trap is no longer necessary in most applications. VACUU-PURE easily handles high vapor loads through its extraordinary condensate compatibility. Thanks to this capability, a gas ballast is unnecessary, avoiding associated disadvantages like the reduction in pumping speed and an increase in noise levels. The integrated regeneration mode enables rapid drying of the pump at the end of the process. This allows sample throughput to be increased significantly as compared to other pump technologies. INCLUDED: The VACUUBRAND VACUU-PURE 10C Screw Pump includes: - 2 x Centering Rings - 2 x Clamping Rings - Power Cord - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

RW 5Y.F42 Robotic Weighing System is a mobile filter weighing station. Its important component is th (more)e multi-range robotic arm, which has a reach of 500 mm and a maximum capacity of 3 kg. The arm moves in several axes and has as many as six degrees of freedom, that is, it bends in six places. Incomparable Microbalance Readability RW 5Y.F42 is synonymous with full automation of filter weight measurement. The device is based on the XA 6.5Y.M.A Microbalance weighing mechanism, which provides incomparable repeatability and a readability [d] of 1 µg. The RW 5Y.F42 enables the weighing procedure and dust determination of up to 42 filters with a diameter of 47 mm. The Cobot’s Helping Hand A cobot working together with the balance takes samples from the magazine, identifies them with a 2D code reader, and then ionizes and weighs them. The use of a cobot equipped with a range of certified safety systems allows the robot to interact directly with laboratory personnel and minimize the space required for its work. Monitoring of ambient conditions records the current environmental circumstances, allows them to be viewed and data reported. What Do You Get When You Buy the RW 5Y.F42? XA 6.5Y.M.A Microbalance with a draft shield Cobot, which is a robot with a gripper that allows you to transport filters between the magazine and the microbalanc Magazine for storing filters (storage capacity: 42 cassettes) Ionizer Camera for casettes identification THB-S Sensor which monitors ambient conditions, mostly temperature, humidity and pressure 5Y weighing terminal for managing the operation of the device QR code reader built into the device PC with RMCS Filters software to manage the operation of the entire device. Ergonomics and Compatibility of RADWAG Products The 10-inch touchscreen display of the 5Y terminal guarantees readability of the result from many angles and comfort of use. The ergonomics of work is also enhanced by touch-free operation of the device. Thanks to the available communication interfaces, the RW 5Y.F42 will connect you to a spreadsheet (USB-C), to a smartphone or tablet (Hotspot), a printer (Ethernet, Wi-Fi, USB-A), a computer (Ethernet, Wi-Fi, USB-A), a barcode scanner (USB-A), as well as to a keyboard and mouse. What Do You Gain When You Buy the RW 5Y.F42? Fully automated weighing system for 47 mm diameter filters Compliance with EN 12341:2014 Time savings compared to the procedure of weighing filters manually Elimination of the human factor as a cause of measurement errors Process management with RMCS Filter software Automatic data recording as well as creating reports and statistics Identification of filters thanks to a system of QR codes applied to the casettes Elimination of the influence of electrostatics on the measurement Mobility of the system Ease of installation and operation.