2 GC 3800 Gas Chromatographs for VARIAN parts

GC-MS Thermo Scientific Trace GC Ultra / ITQ 1100 / TriPlus AS/HS Autosampler System This item was r (more)emoved from a university laboratory where it was surplus to requirements. All system components are in good cosmetic condition. The working condition for each unit is listed below. The Thermo Scientific Trace GC Ultra's service panel has been removed, and some components are missing. The earthing cable is disconnected. Due to the disconnected components and lack of full testing, this system is sold as Spares/Repair. Components and Condition: Thermo Scientific Trace GC Ultra - Model: K04300000000080 - Serial No.: 320070204 - Condition: Not powered on. The service panel has been removed, and some components are missing. The earthing cable is disconnected. Thermo Scientific ITQ 1100 (Polaris Q-Mass Spectrometer) - Model: Polaris Q-Mass Spectrometer - Serial No.: MS211856 - Condition: Powers on with a green power light, and fans are running. No further testing has been conducted. Thermo Scientific DPC (Direct Probe Controller) - Model: Direct Probe Controller - Serial No.: DPC 10513 - Condition: Powers on with a green power light. No further testing. Thermo Scientific TriPlus Autosampler - Model: TriPlus - Serial No.: 20088612 - Condition: Powers on with a green power light. No further testing. Thermo Scientific TP 101 - Model: TP 101 - Serial No.: 20170459 - Condition: Powers on with a green power light. No further testing. Thermo Scientific TP112 TriPlus HS Headspace Turret Injector - Serial No.: 20087277 Thermo Scientific TriPlus TP111 AS Liquid Handler Turret - Serial No.: 20172100 Included Accessories and Components: - Thermo Swap It GC/MS Interface CD - Thermo MSD Transferline Ferrule - Thermo Swap-Tight Ferrule (0.00/0.25/0.32) - Thermo Pro-Cap (0.25/0.32/0.53) - Thermo Direct Insertion Probe (Serial No.: 119300-ODIP) - Thermo TriPlus SPME Kit (Serial No.: 20084014) - Thermo ION Volume Insertion/Removal Tool - Thermo Ion Volume Holder - Alumaseal Ferrule 0.4mm (Pack of 10) - MGVF-005 (Pkt. 5) and MGVF-004 (Pkt. 4) - Thermal Fitting (Part No.: 34705451) - Seal Flat Silicone MM18X7X2 (Part No.: 29003037) - Vespel/Graphite Ferrule 1/16" x 0.5mm ID (Pack of 10) - Graphite Sealing Ring for 8mm Inlet (Pack of 2) - Filament Assembly ION Trap/DSQ II (x3) - Inlet Liner Seal for Trace 2000GCs (Pack of 2) - Graphite Vespel Ferrule for 0.1-0.25 (Pack of 10) - Graphite Vespel Ferrule for 16-003 (Pack of 10) - Graphite Vespel Ferrule for 16-16 (Pack of 10) - Graphite Vespel Ferrule for CE-005 (Pack of 1) - Various wires included

2 GC 3800 Gas Chromatographs for VARIAN parts Without Software Without a computer For parts

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

This Perkin Elmer GC Gas Chromatograph Clarus 480 was removed from a university lab where it was sur (more)plus to requirements. It is in reasonably good cosmetic condition and powers up. The original ECD detector has been removed, leaving mains cables exposed, therefore, this item is listed as Spares/Repair. Part number- N664948ESerial number- 480S13030901

Digital block heater for two aluminum blocks provides precise temperature control in small vessels.  (more)Included PT-1000 temperature sensor allows temperature control directly in the sample vessel. The block heater is ideal for melting and boiling point determination, enzyme reactions, incubation and activation of cultures, immunoassays, DNA denaturation, culture media tests, coagulation tests, blood-urea-nitrogen determinations and in situ hybridizations. Stepless adjustable temperature up to 120°C Timer: Countdown, adjustable from 1 min to 99h 59min Counter: Display of heating time Highly versatile with a large number of blocks Error code display Fixed safety circuit Acoustic signal at end of test Number of blocks: 2 Heat output: 250 W Heating temperature range: Ambient +5°C to 120°C Temperature display: yes Adjustment and display resolution: 1 K Connection for ext. temperature sensor: CT (DIN12878) PT 1000 variation;DIN EN 60751 Kl. A: ≤ ± (0.15 +0.002xITI) K Temperature stability within the blocks at 37°C: ±0.2°C Temperature stability within the blocks at 60°C: ±0.4°C Temperature Homogenity at 37°C: 0.2 K Temperature Homogenity at 60°C: 0.4 K Heatingrate / Heat up time with external sensor: 4.5 K/min Set-up plate material: Aluminium alloy Set-up plate dimensions: 96 x 152 mm Fixed safety circuit: 150°C Timer: yes Time setting range: 1 – 5999 min Dimensions (WxHxD): 151 x 73 x 304 mm Weight: 1.724 kg Blocks included: 1x DB 1.2: Used for Eppendorf microtubes (1.5 ml) Pore size: Ø 11.5 mm No. of holes: 20 Hole depth: 36.9 mm Dimensions (WxDxH): 95 x 76 x 51 mm 2x DB 5.1: Used for 12 mm vials Pore size: Ø 12.7 mm No. of holes: 20 Hole depth: 30.0 mm Dimensions (WxDxH): 95 x 76 x 51 mm 1x 13.9: Used for round bottom tubes (12/13 mm) Pore size: Ø 13.7 mm No. of holes: 16 Hole depth: 48.4 mm Dimensions (WxDxH): 95 x 74 x 51 mm

Detection modes: Absorbance Read methods: End point, kinetic, linear scanning Microplate types: 96-w (more)ell plates Light source: Tungsten halogen Detector: photodiode Wavelength range: 380 to 900 nm Incl. Filters: 340, 405, 450, 490, 630 nm Dynamic range: 0 to 4.0 OD Resolution: 0.001 OD Pathlength correction: no OD accuracy: < 1% at 2.5 OD OD linearity: <1% at 2.5 OD, < 2% at 3.5 OD OD repeatability: < 0.5% at 2.5 OD, < 1.5% at 3.5 OD Reading speed (kinetic): 96 wells: 8 seconds Dimensions (WxDxH): 394 x 406 x 222 mm Weight: 13.6 kg Excl. software. Click for possible GEN5 basic/secure/IVD configurations

Chemagen Chemagic Separation Module I with Software &amp; Accessories This was removed from a unive (more)rsity lab where it was surplus to requirements. Included in the system are; 1 x Chemagic Magnetic Separation Module I10 x Tube Racks :-7 hold 12 x 50ml tubes2 Hold 12 x 15ml tubes1 holds 12 x 0.5ml tubes 1 x Chemagen BiopolymerVulkan TechnicOrder no. 200 03 014The unit powers on but not tested further. 1 x Compaq PCModel - Presario S0000Chemagen/Chemagic Software MSM (Release 5.1.0.6) Installed 1 x DGM MonitorModel - L-1731W 1 x Compaq Keyboard 1 x IBM Mouse All PC equipment powers up and seems to be in full working order. Boxed Accessories:-178 x Genetix Lids (opened)100 x Sealed 96 well 2.2ml storage plates6 x Sealed Nunclon Surface plates10 x Rubber plates5 x 384 well plates (S300RXFL)9 x 96 well 0.1ml slots8 x 100mm Tissue Culture Dishes11 x Chemagen Tubes (PK-400500-036-080403)18 x Microcon YM-100 Regenerated Cellulose38 x 2ml vials17 Packs of MicroAmp Optical Caps (8 caps per strip, 12 strips per pack)25 x Thermo Scientific 0.2ml Skirtled 96 well PCR Plates57 x fisherbrand Dispenser Tips 12.5mlPromega SV96 Total RNA Isolation System2 x Denletstor Metal racks size 38.5 x 15.5cm, 160 squares 1.5 x 15cm each2 x Wash Buffer 6 Bottles (both full) Volume unknown.Promega Vac-Man Laboratory Vacuum Manifold

If you buy a Multifunctional Scale HY10 by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. Multifunctional scales HY10 series is designed to fast and precise determination of mass in industrial conditions. The HY10 scales features a terminal PUE HY10 series in stainless steel housing and a single load cell weighing platform. The HY10 series scales is made of stainless steel OH18N9 including the weighing platform, and it is equipped with 10,1&rdquo;colourful touch screen display, keyboard with numeric and function keys. The scales enables cooperation with an additional weighing platforms. Additionally, the HY10 series offers full functionality available in the terminal PUE HY10 series: programmable display and function keys, designing custom printout templates, designing text data indicated on terminal display. Multifunctional scales HY10 series is offered with a terminal connected to a weighing platform through a cable. Scales HY10 series is available in dual range version on surcharge. Dedicated Applications Smart Editor The application is intended for scales equipped with the HY10 terminal. It does not require any additional installations. Enter the terminal&rsquo;s address in the browser address field and log in. The application enables: - remote databases editing - import of images from the graphic file to the scale - labels import from lb file to the scale - creating and preview of report, e.g. Workflow - dosing processes operation Smart Display The application allows to personalise the scale screen and display it on a computer. The Smart Display enables customization of the display screen in a simple and clear way. Place the individual elements on a grid visible on the screen. These elements can be further scaled to suit user needs. When operated directly on the scale, the user gets a new, refreshed look with the possibility of any configuration of the home screen. If the application is operated via a computer browser, it enables remote control of the desktop or setting larger mass indication window. The Workflow Module will improve work in your company. It enables developing a path of customized weighing process adapted to individual requirements of a particular production system, and next sending it to all weighing instruments cooperating with the E2R. The given process is started on the weighing instrument upon operator logging or after selecting a product, a formulation or an ingredient to which it is assigned. Modifications are made with use of convenient and intuitive interface.