Bio-Rad Tetrad 2 Peltier Thermal Cycler Lab

This was removed from a university lab where it was surplus to requirements. The unit powers up but  (more)when we tried to connect it to a PC with software we had some issues. (Software not included). We installed software on a test PC and it did seem to connect to the RG3000, but it is stating that there is a Fatal Hardware Malfunction. The machine can't be used until the distributor has service it. After starting it again we got another error: Thermistor is Open. We have removed the casing to check inside the unit and cannot find any obvious issues. There is an LCD panel inside that is showing 'TEMP OVER 140/127.5/2.1/152.0'. This displays as soon as the unit is switched on, so it looks like there is some sort of temperature error happening. There are 4 x PTC EPCOS C810 Thermistors in the power supply section of the unit. It's possible that there is a fault with at least one of those. It is in otherwise reasonable cosmetic condition with marks from use, but is sold for spares/repairs The item holds up to 72 x 0.1ml strip tubes.

This G-STORM Thermal Cycler GS00482 was removed from a university lab where it was surplus to requir (more)ements. The unit powers up and is in full working order. It is in good cosmetic condition with minor marks. It has a 2 block cylinder with 48 wells in each block

This VWR UnoCycler PCR Thermal Cycler was removed from a university lab where it was surplus to requ (more)irements. The unit powers up and is in good working order. The touch screen is a little out of calibration but it works well with a mouse. It is in good cosmetic condition with minor marks from use.

Real Time PCR Cycler Corbett Rotor Gene 3000. Fully equipped for real-time amplification, endpoint a (more)nalysis, autocall genotyping, and nucleic acid concentration measurement. Rotor for  72 0.1 ml strip tubes. Excitation source 470nm, 530nm, 585nm, 625nm high power LEDs. 510nm, 555nm, 610nm and 660nm, 580nm, 610nm high pass and bandpass detection filters. Detected fluorophores Sybr-Green I, Fam, Tet, Joe, Vic, Max, Rox, Tamra, Cy3, Cy5, Cy5.5, Tex Red. Temperature range 25 - 99 ° C. Heating / cooling range 2.5 ° C / sec (tube temperature); uniformity +/- 0.01 ° C. Includes PC and software. User manual. Real Time PCR Cycler Corbett Rotor Gene 3000. The Rotor-Gene multi-filter system can detect all available real-time chemistries including Sybr-Green, dual-labelled and MGB probes, FRET and Molecular Beacons.Most DNA amplification enzymes/ buffers can be used on the system to generate Quantitation/Melt data. It is not necessary to use expensive kits that are specific to the instrument. Additionally, Rotor-Gene offers the most user-friendly real-time analysis software system currently available. Using an experiment Wizard, a new real-time protocol can be setup within a matter of minutes in a few easy to follow steps.

Hermle C2417-3202 4 x PCR (32 x 0.2ml) Strip Rotor The Hermle C2417-3202 4 x PCR (32 x 0.2ml) Strip  (more)Rotor is designed for exclusive use with the Hermle MC-24 and MC-24R centrifuges. It achieves a remarkable maximum speed of 13,500 RPM and a maximum RCF of 13,602 x g, making it ideal for high-speed applications. With a capacity to accommodate 4 x PCR strips (32 x 0.2ml), this rotor is specifically tailored for PCR work, offering unparalleled adaptability for a broad spectrum of research and application needs. INCLUDED: The Hermle C2417-3202 4 x PCR (32 x 0.2ml) Strip Rotor includes: - Hermle Z327-200-AC 4 x 200 ml Swing Out Rotor - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Benchmark MultiCycler 332, MultiBlock Thermal Cycler, 3 x 32 x 0.2ml, 115V Display 10” full color  (more)touch screen with adjustable angle Block Temperature Range 4°C - 99.9°C Temperature Accuracy ≤±0.2°C (at 90°C) Features - Dual block format - 3x 32 well blocks - All accept 0.2 mL PCR tubes and strips, flat or dome caps - Each block functions independently - Block temperature range: 4°C - 99.9°C; Lid temperature range: 30 - 112°C - Intuitive Touch Screen Control - Large 10-inch adjustable touch screen - folds away when not in use - Program wizard for fast and easy programming - Advanced program features - Gradient capabilities - up to 8 temperatures per block Designed for laboratories wanting flexibility in their applications, Benchmark’s MultiCycler™ Thermal Cyclers offer multiple, independent cycling blocks in a single unit. Dual or triple block models are available, both offering extremely fast cycling profiles, large touch screen interfaces, self-adjusting heated lids, gradient capabilities, and an easy-to-use program wizard. All programming features are accessed from the large, 10” full color touch screen. The screen can be angled towards the user when in use and then tucked away to save space. A program wizard guides users through the simple protocol set up process. Advanced programming features include gradient, adjustable ramp rates, and time increments and decrements. For multi-user labs, password protection prevents interference of an existing run. A USB provides for unlimited program storage and easy transfer of protocols between MultiCycler machines. The auto-adjusting heated lid prevents condensation and evaporation of samples. Lid temperature can be programmed, and when the block temperature is below 35°C, the lid automatically shuts off. Peltier units allow for exceptionally fast heating and cooling of the blocks. Temperature change is precisely and accurately controlled within tight tolerances by a proprietary algorithm that simulates sample temperature, resulting in fast runs and reproducible results. The wells are arranged in a 4×8 and 6×8 format, allowing for the use of PCR strip tubes in both models. Each block is independently controlled. INCLUDED: The Benchmark MultiCycler 332, MultiBlock Thermal Cycler, 3 x 32 x 0.2ml, 115V includes: - Power Cord - Two Year Manufacturer's Warranty

600 x Thermo MicroAmp Optical 384-Well Reaction Plates with Barcode (4309849) These are sold on beha (more)lf of a client. The lot is brand new and unused. Quantity - An Overpack of 600 plates (12x50)Make/Brand - Applied BiosystemsModel Number - 4309849Product Number - 4309849Exp Date - N/ASKU - PLA-384WELL50-LIF The normal terms and conditions do not apply to this item. This item is non returnable and non refundable.

Varian 7000 FT-IR Spectrometer with FTS 6000 Power Supply This was removed from a university lab wh (more)ere it was surplus to requirements. The unit powers up but we were unable to test it further without the software. It is in good cosmetic condition with marks from use. Included are; Varian SpectrometerModel - 7000 FT-IRSN - 46040-409 Varian Power SupplyModel - FTS 6000SN - PS-0391-0806

If you buy a Multifunctional Scale HY10 by July 31, 2024, you will receive each of these products al (more)ong with a FREE lifetime license for the Workflow Module. Multifunctional scales HY10 series is designed to fast and precise determination of mass in industrial conditions. The HY10 scales features a terminal PUE HY10 series in stainless steel housing and a single load cell weighing platform. The HY10 series scales is made of stainless steel OH18N9 including the weighing platform, and it is equipped with 10,1”colourful touch screen display, keyboard with numeric and function keys. The scales enables cooperation with an additional weighing platforms. Additionally, the HY10 series offers full functionality available in the terminal PUE HY10 series: programmable display and function keys, designing custom printout templates, designing text data indicated on terminal display. Multifunctional scales HY10 series is offered with a terminal connected to a weighing platform through a cable. Scales HY10 series is available in dual range version on surcharge. Dedicated Applications Smart Editor The application is intended for scales equipped with the HY10 terminal. It does not require any additional installations. Enter the terminal’s address in the browser address field and log in. The application enables: - remote databases editing - import of images from the graphic file to the scale - labels import from lb file to the scale - creating and preview of report, e.g. Workflow - dosing processes operation Smart Display The application allows to personalise the scale screen and display it on a computer. The Smart Display enables customization of the display screen in a simple and clear way. Place the individual elements on a grid visible on the screen. These elements can be further scaled to suit user needs. When operated directly on the scale, the user gets a new, refreshed look with the possibility of any configuration of the home screen. If the application is operated via a computer browser, it enables remote control of the desktop or setting larger mass indication window. The Workflow Module will improve work in your company. It enables developing a path of customized weighing process adapted to individual requirements of a particular production system, and next sending it to all weighing instruments cooperating with the E2R. The given process is started on the weighing instrument upon operator logging or after selecting a product, a formulation or an ingredient to which it is assigned. Modifications are made with use of convenient and intuitive interface.

The HX5.EX scale is a modern weighing instrument assuring fast and reliable measurement in hazardous (more) areas classified as zones 1/21 and 2/22. To ensure precision and excellent measurement repeatability, high quality electronic components are used. The weighing platforms offered in wide range of dimensions and maximum capacities, this combined with excellent metrological parameters enables easy selection of an instrument that meets the most demanding requirements. Standard version of the scale is equipped with 2 serial, intrinsically safe RS232 communication interfaces, and with one RS485 interface. They facilitate cooperation with equipment intended for operation in hazardous areas. Possibility to add digital inputs/outputs extends the range of instruments compatible with the indicator by automatic elements compliant with ATEX directive. More demanding customers can use the IM01.EX module, installed in the safe area, which extends the available connectors by Ethernet, USB, 4-20mA/0- 10V analog outputs, Profibus DP and additional digital inputs/outputs. This enables cooperation with external devices: barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. Scale operation requires use of a dedicated PM01.EX power supply, which is not a standard scale component. To operate the scale, order a selected type of the dedicated intrinsically safe power supply. Power supply types: PM01.EX-1 - power supply for operation in ATEX area. Used when it is required to connect the power supply to voltage source placed in hazardous area. PM01.EX-2 - power supply for operation outside ATEX area. Used when power supply connection to voltage source is carried out outside hazardous area. Complex software enables carrying out many tasks connected with mass measurement, e.g. parts counting, checkweighing and statistics. The scales feature user-friendly graphic interface, which can be customized using widgets. This and the large colour display of high resolution guarantee easy and clear transmission of data on current process. Colour bar graph significantly influences performance by signalling whether the weighing result is within declared thresholds or not.

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Temperature range: 16°C to 22°C Cooling power (at 20°C): 600 watt Pump capacity max. 0.4 bar pump: 2 (more)8 l/min Pump capacity max. 3.5 bar pump: 10 l/min Dimensions (WxDxH): 360 x 470 x 590 mm Weight: 52 kg