Axon Instruments GenePix 4000A Microarray Scanner Lab

Odessy LI-COR Unit Model-9120 Lab This item was removed from a university where it was surplus to re (more)quirement. It is in good cosmetic condition and powers on, we are unable to test it further at our facility as it requires software. Software not included.

GenePix 4300A MicroArray Scanners Lab This item was removed from a university where it was surplus t (more)o requirement. It is in reasonably good cosmetic condition and powers on, we are unable to test it further at our facility.

Perkin Elmer ProScanArray HT Microarray Scanner This was removed from a university lab where it was  (more)surplus to requirements. The unit powers up but has not been tested further at our facility. It is in great cosmetic condition with minimal wear.

LGC Biosearch Technologies Araya + Tape Counter Lab This item was removed from a university where it (more) was surplus to requirement. It is in good cosmetic condition and powers on, we are unable to test it further at our facility. Includes the following: Biosearch Technologies Tape Counter Model- TC1412S/N- C521002 5L Water Supply Bottle With PumpModel- DS-AC2102S/N- 1210242 The table the item sits on is included.

VWR Galaxy Miniarray minicentrifuge. Speed of 4,000 rpm. Capacity for 2 microarray slides. Specifica (more)tions: 230 V; 50-60 Hz

The HX5.EX scale is a modern weighing instrument assuring fast and reliable measurement in hazardous (more) areas classified as zones 1/21 and 2/22. To ensure precision and excellent measurement repeatability, high quality electronic components are used. The weighing platforms offered in wide range of dimensions and maximum capacities, this combined with excellent metrological parameters enables easy selection of an instrument that meets the most demanding requirements. Standard version of the scale is equipped with 2 serial, intrinsically safe RS232 communication interfaces, and with one RS485 interface. They facilitate cooperation with equipment intended for operation in hazardous areas. Possibility to add digital inputs/outputs extends the range of instruments compatible with the indicator by automatic elements compliant with ATEX directive. More demanding customers can use the IM01.EX module, installed in the safe area, which extends the available connectors by Ethernet, USB, 4-20mA/0- 10V analog outputs, Profibus DP and additional digital inputs/outputs. This enables cooperation with external devices: barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. Scale operation requires use of a dedicated PM01.EX power supply, which is not a standard scale component. To operate the scale, order a selected type of the dedicated intrinsically safe power supply. Power supply types: PM01.EX-1 - power supply for operation in ATEX area. Used when it is required to connect the power supply to voltage source placed in hazardous area. PM01.EX-2 - power supply for operation outside ATEX area. Used when power supply connection to voltage source is carried out outside hazardous area. Complex software enables carrying out many tasks connected with mass measurement, e.g. parts counting, checkweighing and statistics. The scales feature user-friendly graphic interface, which can be customized using widgets. This and the large colour display of high resolution guarantee easy and clear transmission of data on current process. Colour bar graph significantly influences performance by signalling whether the weighing result is within declared thresholds or not.

Precision in PRO version The CY10 series precision balance is designed for fast, accurate and repeat (more)able weight determination. It comes with an advanced PUE CY10 terminal, and that means working comfort with a 10-inch high-resolution display with a smooth and intuitive interface. Software for special tasks Thanks to the terminal advanced software, the CY10 series precision balance: Cooperates with up to 2 weighing platforms Continuously updates all statistical data after the next measurement is entered into the balance’s memory – either globally (regardless of the weighed commodity) or separately for each weighed commodity selected from the database Has a Tare mode expanded to include End-product issue mode capability Works with RFID tags* (accessing personal data as well as marking specific goods or recipe ingredients in the database). Precision balance and labelling scale in one device If you need a labeling scale, the CY10 is the perfect solution. With a terminal that: Cooperates with the computer program Label Editor R02 Is compatible with ZEBRA label printers Supports single labels, bulk labels and bulk from bulk labels Allows import/ export of label designs using a pendrive Enables you to assign labels to goods or customers and print a global label The CY10 series precision balance can operate as a labeling scale. Light or dark? Which color theme will you set on your CY10 balance? Both are user-friendly and clear, but we are curious which one you like more. Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13,56 MHz

Do you need a moisture analyzer that not only determines moisture or dry matter content with impress (more)ive accuracy, but also performs a digital audit, responds to your voice commands and sends you light messages? If so, learn about the functionality of the ELLIPSIS series of moisture analyzers: It Dries in 4 Ways The MA 5Y.IC Moisture Analyzer offers you four drying profiles: standard, mild, fast and step. The standard profile is the usually used drying profile. It allows the most accurate determination of moisture content. The mild profile is designed for drying substances that are sensitive to the rapid heat released by the filaments, which heat full power at the initial stage of the process. An example of such a substance is leather. You will use the fast profile for samples with significant moisture content – of the order of even several tens of percent. The step profile will be ideal for drying substances that contain more than 15 percent moisture. Within this profile you can define any three temperatures. You will choose the values of temperature and duration of heating experimentally. What Drying Temperature Should I Set? The drying temperature determines the duration of the process. Its value depends on the type of material. If the temperature is too low, it will under-dry the sample and, consequently, unnecessarily increase the measurement time, while if it is too high, it will cause a burning effect on the material. The drying temperature for the traditional (oven) method is determined by industry or factory standards. If there are no standards, you will select the temperature experimentally. The maximum drying temperature on the MA 5Y.IC Moisture Analyzer is 160°C. How Do I Finish the Drying? In 4 Ways The MA 5Y.IC Moisture Analyzer has four finish modes: automatic, manual, time-defined and user-defined. Automatic mode You define the moisture loss limit value in 60 seconds. When the moisture analyzer reaches the set criterion, the measurement will automatically end. Manual mode You terminate the measurement yourself by pressing the STOP button. Time-defined mode The measurement ends after the set time has elapsed regardless of the result. You have up to 99 hours 59 minutes to manage! User-defined mode When you remove all volatiles from a sample, by definition, its mass should be constant. During drying, the dry mass of the sample is defined by a condition: if the mass of the sample is stable within 1 mg during the observation time (Auto 1-5), we consider that all volatile components have been removed from its structure. Digital Weighing Auditor Ensures that your moisture analyzer is ready for use. What is more, it informs about the need for a moisture analyzer inspection or a periodic audit of the moisture analyzer’s accuracy and sensitivity. 10-Inch Display Bigger screen – 10’’ – means more information in one place. On the new ELLIPSIS terminal, you will see up to 3 screens, widgets, graphs, statuses, notes, handy measurement history. Uncompromising User Verification For the first time ever, the moisture analyzer will verify the user using a password, RFID card, fingerprint reader, facial recognition mechanism, or any combination of these. Ambient Light – an Innovative Way for the Moisture Analyzer to Communicate With the User The light colour will tell you about status, process results, procedures, or alerts. Hotspot Use the moisture analyzer on any device connected to it. This can be a smartphone, tablet, or computer. RFID ELLIPSIS works with RFID tags* that can be used to tag your products or formulation ingredients in the database. They can also be used to identify a user. Live Note – Note Down Your Conclusions It’s the first time you can add a voice memo to a measurement series or procedure report. If you prefer to write it down, ELLIPSIS allows you to add a text note. Handy Library This is where a series of recent measurements or a report ready for digital signature, according to 21 CFR Part 11, can be found. Widgets Prepared to display what you need most at any given moment. 21 CFR Part 11 Do you work in the pharmaceutical industry? Do you need a digital signature? We are offering the moisture analyzer which as a standalone fully meets the requirements of 21 CFR Part 11/ EU GMP Annex 11. Full data security Electronic signatures Validations Electronic records Audit trails Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13.56 MHz

IKA C-Mag MS 10 Magnetic Stirrer Speed Range 100 to 1,500 RPM Stirring Quantity Max. 15 l Set-up  (more)Plate Material Ceramic Features - Powerful motor for stirring quantities of up to 15 l (H2O) - Elevated control panel for protection against leaking liquids - Speed range: 100 - 1500 rpm - Simple controls ensure ease of use an integration in a lab space - Small footprint for optimization of benchtop space usage The IKA C-Mag MS 10 Magnetic Stirrer is a powerful and versatile laboratory tool designed for stirring quantities up to 15 liters (H2O) without heating. Featuring a durable ceramic set-up plate, it offers excellent chemical resistance, making it suitable for a wide range of applications. The stirrer operates within a speed range of 100 to 1500 rpm, controlled via a scale from 0 to 6, and can accommodate stirring bars up to 80 mm in length. The elevated control panel protects against leaking liquids, ensuring safe and reliable operation. With dimensions of 300 x 105 x 415 mm and a weight of 6 kg, the IKA C-Mag MS 10 is compact and easy to integrate into any laboratory setting. It operates efficiently within an ambient temperature range of 5 to 40 °C and relative humidity up to 80%, with a motor rating output of 1.5 W and a power input of 30 W.

Eppendorf A-4-81 Microplate MTP Buckets # 022638840 The Eppendorf 022638840 Replacement MTP/Flex Buc (more)kets for Rotor Model A-4-81-MTP (Pack of 4) is a reliable and durable solution for your laboratory's sample processing needs. These replacement buckets are designed to fit the A-4-81-MTP rotor, ensuring seamless integration with your Eppendorf centrifuge system.The buckets have a user-friendly design and a secure locking mechanism that keeps your samples safe during centrifugation. With a capacity of up to 4 microtiter plates, they offer ample space for a range of laboratory applications, including working with DNA, RNA, proteins, and other biomolecules.Upgrade your lab's sample processing capabilities with the Eppendorf 022638840 Replacement MTP/Flex Buckets for Rotor Model A-4-81-MTP and experience the exceptional quality and reliability that Eppendorf is known for. Eppendorf A-4-81 Microplate MTP Buckets #022638840 Technical SpecificationsMaximum Rotational Speed4,000 RPMMaximum RCF2,900 x gINCLUDED: The Eppendorf A-4-81 Microplate MTP Buckets # 022638840 includes: - Full 6 Month Parts and Labor Warranty