Radwag Label Editor R02

Spinning top lift BOY 08 510.00 PROLABO 20 x 20 cm Lifting support, lifting table for laboratory Tab (more)letop dimensions: 200 x 200 mm With traces of wear

This Irori AccuTag 100 Scanning Station  Model: At-100-CS-CE was removed from a university lab  (more)where it was surplus to requirements. The item is in reasonable cosmetic condition. There are scratches/dents on the surface, along with stains. The accessories have been used and thus have broken seals. The item was plugged in, but there wasn't any clear indication it had powered on. We were unable to test it further without a PC connection. Also included are the following:1x AccuTag Synthesis Manager Version 1.01x AccuTag Synthesis Manager Version 2.2612x Irori Radio Frequency Tag1x PSU1x DE-9 cable

This Adaptif Phototonics Polarization Synthesizer Model. A3300 was removed from a university lab whe (more)re it was surplus to requirements. The unit powers on and is in good cosmetic condition. The power light does not illuminate when switched on but we could hear it running. No PSU was supplied so we used a multi-adapter (not included). The APC input and output ports are in good cosmetic condition. The control button moves freely.

Sheen Wet Abrasion Scrub Tester Model - 903 Lab This item was removed from a university where it was (more) surplus to requirement. It is in reasonably good cosmetic condition and powers on, we are unable to test it further at our facility.

RareCyte CyteFinder & CyteSealer Liquid Biopsy Analysis System This system was removed from a l (more)aboratory where it was surplus to requirements. Both units power up and are in good cosmetic condition with marks from use. It comes with 8 x Trays (53.5 x 16cm). One tray has been labelled as 'Not moving'

This Hema-tek 2000 Slide Stainer Model - 4488A was removed from a university lab where it was surplu (more)s to requirements. The unit powers up and runs. The lab informed us that it had no known faults prior to removal. It is in good cosmetic condition with minor marks from use.

VACUUBRAND VACUU-Select Complete Benchtop Controller Upper Measuring Limit 810 torr Lower Measuri (more)ng Limit 0.1 torr Accuracy Less than +/- 1 mbar/hPa/torr Features - Supplied complete and ready for use, including integrated valve and common hose connections - Predefined vacuum applications and automatic boiling point detection saves time - Simple setup - connect VACUU·SELECT in-line between pump and vacuum application - Integrated vent valve allows inert gas connection - Integrated check valve minimizes interaction with other applications on the same vacuum supply The VACUU·SELECT complete controller provides enhanced process efficiency to applications supported by a vacuum source such as a basic pump or a powerful vacuum network. The VACUU·SELECT controller has you covered. Use manual set-point-control for simple processes, run pre-defined applications at the touch of a button, or create your own application with simple drag-and-drop editing. The controller is available as a benchtop unit, ready for mounting on lab scaffolding, or as a built-in version for lab casework. The integrated controller includes the VACUU·SELECT vacuum controller, a check valve, and a chemical-resistant solenoid isolation valve. The ceramic vacuum sensor and venting valve are built right into the body of the VACUU·SELECT controller. The compact unit is easy to install and setup. With its intuitive, application-based interface, the controller offers predefined vacuum processes for all common laboratory applications. In the case of solvent evaporation, it detects the boiling pressure and then holds the pressure level stable using two-point control.INCLUDED: The VACUUBRAND VACUU-Select Complete Benchtop Controller includes: - VACUU·SELECT complete controller bench-top device - Solenoid valve - Non-return valve - Integrated ceramic diaphragm vacuum sensor - Venting valve - Power supply - Operator's Manual - Manufacturer's Documentation - 2 Year Manufacturer's Warranty