Servomex Analyser CO2 Series 1400 Analyser Lab

Designed to maximize turnaround time, RAPIDLab 1200 Systems have the capacity to enhance blood gas t (more)esting efficiency in the clinical laboratory by combining testing speed and reliability with low maintenance. RAPIDLab 1200 systems are our proven solution for high-volume critical care testing sites. Leverage the benefits of RAPIDLab 1200 Systems: Comprehensive test menu addresses a variety of critical care testing needs Intuitive operation and minimal maintenance help increase productivity without increasing staff. Industry-proven accuracy and reliability through long-life Ready Sensor electrode technology Biosafe automatic sampling system with clot detection and clearance Effortless onboard Automatic Quality Control (AQC) for enhanced quality assurance and regulatory compliance Assays Blood gas: pH, pCO2, pO2 Electrolytes: Na+, K+, Ca++, CI- Metabolites: Glucose, Lactate CO-oximetry: tHb, HHb, O2Hb, sO2, COHb, MetHb, Neonatal Total Bilirubin Dimensions (WxHxD): 584 x 572 x 559 mm Weight: 29.5 kg

Dräger X-am 5100 Gas Analyser Lab This item was removed from a university where it was surplus to re (more)quirement. It is in excellent cosmetic condition and powers on, we are unable to test it further at our facility. This item includes the charging dock and additional Type E, Type I and Type A plug fittings.

ATI Portasens lll Gas Leak Detector Kit Model D16 with H2O2 Sensor Lab This item was removed from a  (more)university where it was surplus to requirement. It is in very good cosmetic condition and powers on, we are unable to test it further at our facility. The gas leak detection kit contains the following items: 1 x main D16 detection unit1 x ATI H2O2 sensor1 x H10 Sensor Keeper 00-09811 x Sampling Wand for localised detection2 x Tenenergy 10,000 mAh NiMH rechargeable batteries1 x Intellicharger Newi2 charger with power cable1 x Dwyger Instuments Minimaster flow meter1 x 1/4" straight connector1 x USB cable1 x hard carry case

ATI Portasens lll Gas Leak Detector Kit Model D16 with H2O2 Sensor Lab This item was removed from a  (more)university where it was surplus to requirement. It is in very good cosmetic condition and powers on, we are unable to test it further at our facility. The gas leak detection kit contains the following items: 1 x main D16 detection unit1 x ATI H2O2 sensor1 x H10 Sensor Keeper 00-09811 x Sampling Wand for localised detection2 x Tenenergy 10,000 mAh NiMH rechargeable batteries1 x Intellicharger Newi2 charger with power cable1 x Dwyger Instuments Minimaster flow meter1 x calibration t-fitting1 x filters1 x 1/4" straight connector1 x USB cable1 x hard carry case

Servomex Analyser Series 1400 CO2 Analyser Lab This item was removed from a university where it was  (more)surplus to requirement. It is in good cosmetic condition and powers on, we are unable to test it further at our facility.

This Gasmet FT-IR Gas Analyser Spectrometer Model - DX4030 was removed from a university lab wh (more)ere it was surplus to requirement. The unit powers up and we have run a hardware check. Acceptable values for hardware parameters: Cell temp: close to ambient tempCell pressure: close to ambient pressureSource intensity: >50% (original =100%) - Unit showed 89%Interf height: >3V when cell is filled with zero gas (original approx 5.5V - Unit showed 3.57VInterf center: 2000...3000 point - unit showed 2483 pointsElectronic temp: 0...50ºC - unit showed 21.43Detector temp: -37ºC - Unit showed -37.08ºCExt detector temp: +25ºC - Unit showed 19.82ºC Nothing seems out on the acceptable values for the hardware parameters. We then ran the Zero Calibration check after flushing the air for 3 minutes.The unit showed - Min: 115.0000 Max: 58825.0000Acceptable values for Maximum background spectrum are >40 000 or >70% of original. The system is in good cosmetic condition but has some minor marks from use. It comes in Hardigg Storm Case with:-2 x Gasmet Battery UnitsGasmet Software CDQuantitech DongleGasmet DongleGasmet DX4030 Quick Reference Cards2 x Black carry cases

Unused demo product in original packaging. Great condition. 12 months warranty. For: - Hei-Tec - Hei (more)-Connect - Hei-End - Hei-PLATE Mix 'n' Heat Core

Climet Model CI-95+ Microbial Air Sampler Lab This item was removed from a university where it was s (more)urplus to requirement. It is in good cosmetic condition and powers on, we are unable to test it further at our facility. This item does not include a battery pack and charger.

Stainless steel platform scale with four sensors No matter where you place the load on the platform, (more) the result will always be correct. This is due to the four sensors built into the platform. You will appreciate this especially when weighing an irregularly shaped object. It has been with us for years, and will stay for a long time to come The LCD display has accompanied us for long years. During this time it has proven its reliability. It guarantees the readability of the result from many angles and is energy efficient. Inner power No access to mains power? Power failure? No problem. Thanks to its internal rechargeable battery, the H315 scale works anyway (up to 7 hours). Power supply is available at an extra charge. As standard, the scale is equipped with a RS232 cable, to which you can connect most of the accessories from our range. Not just weighing But also parts counting, percent weighing, animal weighing and peak hold. The power of H315’s working mods. Do you require fast and repeatable weight measurement under difficult conditions? The H315 scale is made for that! Work as you like The PUE H315 terminal sits on a 3-meter cable that allows you to hang the terminal on the wall. This allows you to arrange your weighing workplace in many ways. The power of steel The use of stainless steel guarantees you a long life for the scale. It is not afraid of contact with moist objects or accidental splashes. The membrane keyboard is another argument in the discussion of the water resistance of this scale. If you need a dual-range scale, we can make one for you at an extra cost.

The HX5.EX scale is a modern weighing instrument assuring fast and reliable measurement in hazardous (more) areas classified as zones 1/21 and 2/22. To ensure precision and excellent measurement repeatability, high quality electronic components are used. The weighing platforms offered in wide range of dimensions and maximum capacities, this combined with excellent metrological parameters enables easy selection of an instrument that meets the most demanding requirements. Standard version of the scale is equipped with 2 serial, intrinsically safe RS232 communication interfaces, and with one RS485 interface. They facilitate cooperation with equipment intended for operation in hazardous areas. Possibility to add digital inputs/outputs extends the range of instruments compatible with the indicator by automatic elements compliant with ATEX directive. More demanding customers can use the IM01.EX module, installed in the safe area, which extends the available connectors by Ethernet, USB, 4-20mA/0- 10V analog outputs, Profibus DP and additional digital inputs/outputs. This enables cooperation with external devices: barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. Scale operation requires use of a dedicated PM01.EX power supply, which is not a standard scale component. To operate the scale, order a selected type of the dedicated intrinsically safe power supply. Power supply types: PM01.EX-1 - power supply for operation in ATEX area. Used when it is required to connect the power supply to voltage source placed in hazardous area. PM01.EX-2 - power supply for operation outside ATEX area. Used when power supply connection to voltage source is carried out outside hazardous area. Complex software enables carrying out many tasks connected with mass measurement, e.g. parts counting, checkweighing and statistics. The scales feature user-friendly graphic interface, which can be customized using widgets. This and the large colour display of high resolution guarantee easy and clear transmission of data on current process. Colour bar graph significantly influences performance by signalling whether the weighing result is within declared thresholds or not.

IKA KS 4000ic Incubator Shaker Type of Movement Orbital Temperature Setting Range 12°C - 80 °C Speed (more) Range 10 to 500 RPM Features - Large LED display for speed and time settings - Controls with antimicrobial coating for reduction of bacteria - Integrated PID temperature control (use of two PT 1000 temperature sensors) - Junction box in the workspace for connection of an additional temperature sensor e.g. PT 1000.60 - Electronic temperature and speed control - Electronic timer switch: 0 – 999 h (set by the minute or by the hour) - Optional built-in cooler for connection to an external cooling unit e.g. RC 2 basic / control - Unit switches off automatically if disturbed - Unit stops automatically when hood is lifted - Collecting tray with drain hose on rear of unit - Simple operation - All functions can be controlled and documented with labworldsoft - Attachments are not included in delivery, please order seperatly The IKA KS 4000ic Incubator Shaker combines precise control and user-friendly features, ideal for laboratory applications. It features a large LED display for speed and time settings, antimicrobial-coated controls, and integrated PID temperature control with dual PT 1000 sensors. The electronic timer switch allows settings from 0 to 999 hours, while the unit includes options for an external cooling connection. Safety mechanisms, such as automatic shutoff when disturbed or hood lifted, ensure reliable operation. With a permissible shaking weight of 20 kg, a speed range of 10-500 rpm, and a temperature range from 12°C to 80°C, this shaker provides optimal performance for your lab needs.