Mutek Infrared Laser System - TLS 150, 0LS150, KMPV50-0.5-J2 Lab

This Perkin Elmer AutoIMAGE FT-IR Microscope was removed from a university lab where it was surplus  (more)to requirements. The item powers on and is in a reasonable used cosmetic condition. Included with it is a Perkin Elmer LC Separation Notes Version 1.0 Disc

This Perkin Elmer AutoIMAGE FT-IR Microscope was removed from a university lab where it was surplus  (more)to requirements. The item powers on and is in a reasonable used cosmetic condition. Included with it is a Perkin Elmer LC Separation Notes Version 1.0 Disc

Mutek Infrared Laser System - TLS 150, 0LS150, KMPV50-0.5-J2 Lab The lab confirmed that the sys (more)tem has not been used for 10 years but was working prior to being put away into storage. Mutek Infrared Laser System The Item Powers on and is in Good Condition with Some WearModel - 0LS150 Mutek Infrared TLS 150Model - TLS 150 Kolmar Technologies Infrared Detector Model - KMPV50-0.5-J2 Kolmar Technologies Infrared Detector PSU Has no Information Plate

Varian 7000 FT-IR Spectrometer with FTS 6000 Power Supply This was removed from a university lab wh (more)ere it was surplus to requirements. The unit powers up but we were unable to test it further without the software. It is in good cosmetic condition with marks from use. Included are; Varian SpectrometerModel - 7000 FT-IRSN - 46040-409 Varian Power SupplyModel - FTS 6000SN - PS-0391-0806

This Gasmet FT-IR Gas Analyser Spectrometer Model - DX4030 was removed from a university lab wh (more)ere it was surplus to requirement. The unit powers up and we have run a hardware check. Acceptable values for hardware parameters: Cell temp: close to ambient tempCell pressure: close to ambient pressureSource intensity: >50% (original =100%) - Unit showed 89%Interf height: >3V when cell is filled with zero gas (original approx 5.5V - Unit showed 3.57VInterf center: 2000...3000 point - unit showed 2483 pointsElectronic temp: 0...50ºC - unit showed 21.43Detector temp: -37ºC - Unit showed -37.08ºCExt detector temp: +25ºC - Unit showed 19.82ºC Nothing seems out on the acceptable values for the hardware parameters. We then ran the Zero Calibration check after flushing the air for 3 minutes.The unit showed - Min: 115.0000 Max: 58825.0000Acceptable values for Maximum background spectrum are >40 000 or >70% of original. The system is in good cosmetic condition but has some minor marks from use. It comes in Hardigg Storm Case with:-2 x Gasmet Battery UnitsGasmet Software CDQuantitech DongleGasmet DongleGasmet DX4030 Quick Reference Cards2 x Black carry cases

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

A Simple Western size assay is an automated Western – no gels, no transfer devices, no blots, no fil (more)m and no manual analysis. Simple Westerns take place in a capillary. Wes automates all steps of the process for you including sample loading, protein separation, immunoprobing or labeling, washing, detection and data analysis. Up to 25 samples can be processed in a single run. Wes performs Simple Western size-based assays: Immunoassay and Total Protein assay. All you have to do is pipette your samples and immunoreagents into Wes’s pre-filled plate, load the capillary cartridge and press start. Sample Required Total Protein: 0.3-1.2 µg lysate Sample Required Immunoassay Charge: 0.6-1.2 µg Volume Required Total Protein: 3 µL/well Volume Required Immunoassay Charge: 3 µL/well Size or pI Range Total Protein: Molecular weight (MW) ladders range from 2-440 kDa Size or pI Range Immunoassay Charge: Molecular weight (MW) ladders range from 2-440 kDa Sizing CV Total Protein: <10% Sizing CV Immunoassay Charge: <10% Intra-assay CV Total Protein: <15% Intra-assay CV Immunoassay Charge: <15% Resolution (± percent difference in MW) Total Protein: ± 15-20% for MW <20 kDa, ±10 % for MW > 20 kDa Resolution (± percent difference in MW) Immunoassay Charge: ± 15-20% for MW <20 kDa, ±10 % for MW > 20 kDa Quantitation CV Total Protein: <20% Quantitation CV Immunoassay Charge: <20% Dynamic Range Total Protein: 2-3 logs Dynamic Range Immunoassay Charge: 3 logs Sensitivity Total Protein: ng Sensitivity Immunoassay Charge: Low pg Capillary: 5 cm, 100 µm, 400 nL Dimensions (HxWxD): 360 x 360 x 570 mm Weight: 23 kg

With use of IM01.EX communication module it is possible to expand communication interfaces range of  (more)the HX5.EX indicator. The module is installed outside the hazardous area, and connected to the indicator using intrinsically safe interface. IM01.EX allows to establish communication between the scale and various accessories, e.g. barcode scanners, printers, displays, control buttons, light signalling towers, buzzers and other controlling/signalling devices. It also enables connection with systems of automatic adjustment and control of industrial processes, and with superior IT systems. IM01.EX-4 interfaces: 2 x RS232, USB, 4 IN, 4 OUT (digital), Ethernet, Profibus DP. It is possible to configure module interface quantity following the Interface Configuration Table that is to be found in product data sheet.

IKA Mini MR standard Speed Range 0 - 2,500 RPM Maximum Load 2 kg Stirring quantity max. per stirring (more) position (H2O) 1 liter Features - Modern magnet coil technology ensures reliable stirring. - Wear-free drive with no moving parts for longevity. - High IP protection class (IP 65) for resistance against dust and water. - Chemically resistant materials used for both set-up plate and casing. - Slip-proof stand ensures safety during operation. The IKA Mini MR Standard, a compact magnetic stirrer designed for efficient stirring tasks without heating. With a stirring capacity of up to 1000 ml (H2O), it offers versatility for various laboratory applications. With a wide speed range from 0 to 2,500 rpm, the MR Standard offers precise control over stirring processes. The white set-up plate allows for easy observation of color reactions, enhancing experimental monitoring. Constructed with durable polyester material, the set-up plate ensures stability and longevity. Equipped with a turning knob for speed adjustment, it offers user-friendly operation. Whether in research, education, or industrial settings, the Mini MR Standard delivers reliable stirring performance in a compact package.INCLUDED: The IKA Mini MR standard includes: - IKA Mini MR standard - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Benchmark R2020-1520 Tube holder, 11 x 1.5/2.0, 2/pk (1 pack included) The Benchmark R2020-1520 Tube (more) Holder, 11 x 1.5/2.0, 2/pk is for use with Benchmark Rotomini and Rotomini Plus Series Tube Rotators. INCLUDED: The Benchmark H3770-CSTF Clamp set for H3770 Chemically resistant/inert teflon, includes rod and clamp includes: - Set of 11 x 1.5/2.0 Tube Holders - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

dimensions (hxwxl): 215x210x195 mm