Aperio Scanscope CS 20X Automatic Slide Scanning Microscope Scanner w/o Computer

Leica S 6D Stereo Microscope 6.3x - 40x with Leica L2 Lightbox and Schott KL 1500 Electronic This sy (more)stem was removed from a university lab where it was surplus to requirements. The Leica S 6D stereo microscope is in good condition with minor wear. The Leica L2 lightbox is missing its power lead, while the Schott KL 1500 light source is in good condition and fully operational. The system comprises the following: - Leica S 6D Stereo Microscope - Model: S 6D - Serial No.: N/A - Leica L2 Lightbox - Model: L2 - Art No.: 10 446385 - Serial No.: N/A - Schott KL 1500 Electronic - Model: KL 1500 - Serial No.: N/A

Nikon OPTIPHOT-2 Microscope System with Sony CCD-IRIS Camera This system was removed from a universi (more)ty lab where it was surplus to requirements. All included item are in good cosmetic condition. The microscope powered on via test leads due to a disconnected door trip switch.Voltage selector, lamps, and stage movement are all functioning correctly. The cabinet is faulty, but the scope inside is operational. System Components: - Microscope Base: Nikon OPTIPHOT-2 with Nikon Transformer Model UN - Objectives Included: - Nikon 241187 M Plan 40/0.40 210/0 SLWD - Nikon 322002 M Plan 100 0.90 Dry 210/0 - Nikon 322580 M Plan 60 0.80 210/0 - Nikon 334439 M Plan 40 0.65 210/0 - Nikon 328356 M Plan 20 0.4 LWD 210/0 - Additional Equipment: - Bruker Infrared Microscope Power Supply - Door Trip Switch Override - Sony CCD-IRIS Camera Condition and Testing:The microscope was powered on using test IEC leads due to the door trip switch being disconnected, preventing a direct power connection.- Voltage selector is operational. - Both lamps power on as expected. - Stage movement is functioning correctly.

Zeiss Stemi SV 11 Dual Viewing Discussion Teaching Stereo Microscope Lab This item was removed from  (more)a university where it was surplus to requirement. It is in good cosmetic condition and in good working order. This item features the following: - 4 x Zeiss W-PL 10 x / 23 eyepieces (45 50 44) - XXX CellTech Microscope Stand - Zeiss Dual Observation Bridge

This item has just arrived in our stock. Please enquire for further details.

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Motic Panthera E2 Trinocular Compound Microscope Manufactured to Withstand the Time With the new mic (more)roscope Series Panthera E2, your decision is distinct. This microscope series allows to experience Life Sciences in a new way, with the best possible learning effect. From now on, you achieve your teaching goals in the easiest way, with the highest precision and accuracy that meet all your intentions in mind. Even in a small lab with a small budget, these new technologies from Motic will convince you.Panthera E2 microscopes combine high-quality materials and precise engineering to a persistent and resilient construction. The smooth operation of the mechanics is self-evident for fast and reliable results, responsible for shifting your daily work in the classroom and lab to a higher level of quality. User-friendly design, robust for tough environments, and unique features grants the best performance. Models of this series convince positively in smooth operation and haptic.Robust Functionality for Demanding Environments Panthera E2 was developed by listening to your objectives in mind. Features like a reversed 4-fold nosepiece, a rackless X/Y-stage with a standard slide holder and an upper limit stop fulfill users' demands. The standard eyepiece tubes can be adjusted to accommodate different physiques. In addition, all tubes are rotatable. Together with a small footprint and compact design worries about small working places or storage problems are obsolete.Strong Optical Performance with Ultra Contrast Optics The Panthera E2 series is equipped with new Ultra Contrast (UC) Plan Achromatic objectives in a range from 4X to 100X magnification. These objectives together with neutral eyepieces guarantee the best performance in terms of color fidelity and contrast. A fully corrected intermediate image for digital access is granted. The optional 100X/0.8 "Dry objective" is especially favorable in environments where the time-consuming immersion procedure is considered too difficult and complicated.Efficiency and Energy Saving LED Illumination Setup The low consumption LED light source in a Fixed Koehler setup stands for a "cool" illumination with a long lifetime. An unbeatable key feature for outdoor activities: A USB port in the stand grants the functionality of the microscope independent from the mains by a power bank.Close to your Individual Applications Panthera E2 microscopes can be upgraded for different contrast methods: Phase contrast for unstained samples from botany, zoology, and medicine is a classic, Darkfield for impressive images from protozoa is on the verge of extinction, POL contrast for birefringent structures is an underrated method for biology and medicine. For plastics and foils from the industrial lab, this method is standard.Click Here to View Product Video INCLUDED: The Motic Panthera E2 Trinocular Compound Microscope includes: - 4X/0.10 (WD 30.5mm), 10X/0.25 (WD 17.4mm), 40X/0.65/S (WD 0.6mm), 100X/1.25/S-Oil (WD 0.16mm) Objectives - Dust Cover - Power Cord - Allen Key - Immersion Oil (5ml) - 5 Year Manufacturer's Warranty

Chemometec A/S NucleoCounter NC-200 Automated Cell Counter System Lab This system was removed from a (more) university lab where it was surplus to requirement. Both the Chemometec A/S NucleoCounter NC-200 and Laptop are in very good cosmetic condition and powered up, we are unable to test them further at our facility. Please note that this system does not include the software required to operate but the original laptop is included as it may have useful hardware. Nucleocounter C-200Serial No. 9000201112003522 Lenovo Thinkpad T15 laptopWindows 10 operating systemSerial No. PF-2J9PPX Also includes the following: Included:2 x Low-voltage power supplies1 x Data lead

Stainless Steel HRP.H Platform Wherever high readability and precision are important. Wherever good  (more)repeatability in harsh industrial conditions matters. Stainless Steel HRP.H Platforms are the ideal solution for any type of industry. Repeatability that cannot be repeated by others Stainless Steel HRP.H Platforms have a built-in internal adjustment system. Automatic internal adjustment guarantees the best quality of work and repeatability of results. You save time and avoid the inconvenience of manual adjustment. Unbreakable Stainless Steel HRP.H Platforms feature a modern electromagnetic mechanism design in a sealed steel housing and overload protection. The use of stainless steel for the pan guarantees you a long life of the platform. Fearless of its contact with moist objects or accidental splashing. Stainless Steel HRP.H Platforms are distinguished by a high degree of protection IP 67. For an additional charge we will make HRP platforms in Ex version, but in order for the device to work in explosive areas, you need to supply the PUE HX5.EX terminal. Use the potential Stainless Steel HRP.H Platforms work with one of two weighing terminals: PUE HY10 or PUE 7.1. The terminals’ software enables you to archive your work results, ensures data safety, and allows the platforms to work with powerbanks from our offer. In turn, you will select appropriate antivibration tables for the platforms, and thus increase the readability of your measurements.

Do you need a moisture analyzer that not only determines moisture or dry matter content with impress (more)ive accuracy, but also performs a digital audit, responds to your voice commands and sends you light messages? If so, learn about the functionality of the ELLIPSIS series of moisture analyzers: It Dries in 4 Ways The MA 5Y Moisture Analyzer offers you four drying profiles: standard, mild, fast and step. The standard profile is the usually used drying profile. It allows the most accurate determination of moisture content. The mild profile is designed for drying substances that are sensitive to the rapid heat released by the filaments, which heat full power at the initial stage of the process. An example of such a substance is leather. You will use the fast profile for samples with significant moisture content – of the order of even several tens of percent. The step profile will be ideal for drying substances that contain more than 15 percent moisture. Within this profile you can define any three temperatures. You will choose the values of temperature and duration of heating experimentally. What Drying Temperature Should I Set? The drying temperature determines the duration of the process. Its value depends on the type of material. If the temperature is too low, it will under-dry the sample and, consequently, unnecessarily increase the measurement time, while if it is too high, it will cause a burning effect on the material. The drying temperature for the traditional (oven) method is determined by industry or factory standards. If there are no standards, you will select the temperature experimentally. The maximum drying temperature on the MA 5Y Moisture Analyzer is 160°C. How Do I Finish the Drying? In 4 Ways The MA 5Y Moisture Analyzer has four finish modes: automatic, manual, time-defined and user-defined. Automatic mode You define the moisture loss limit value in 60 seconds. When the moisture analyzer reaches the set criterion, the measurement will automatically end. Manual mode You terminate the measurement yourself by pressing the STOP button. Time-defined mode The measurement ends after the set time has elapsed regardless of the result. You have up to 99 hours 59 minutes to manage! User-defined mode When you remove all volatiles from a sample, by definition, its mass should be constant. During drying, the dry mass of the sample is defined by a condition: if the mass of the sample is stable within 1 mg during the observation time (Auto 1-5), we consider that all volatile components have been removed from its structure. Digital Weighing Auditor Ensures that your moisture analyzer is ready for use. What is more, it informs about the need for a moisture analyzer inspection or a periodic audit of the moisture analyzer’s accuracy and sensitivity. 10-Inch Display Bigger screen – 10’’ – means more information in one place. On the new ELLIPSIS terminal, you will see up to 3 screens, widgets, graphs, statuses, notes, handy measurement history. Uncompromising User Verification For the first time ever, the moisture analyzer will verify the user using a password, RFID card, fingerprint reader, facial recognition mechanism, or any combination of these. Ambient Light – an Innovative Way for the Moisture Analyzer to Communicate With the User The light colour will tell you about status, process results, procedures, or alerts. Hotspot Use the moisture analyzer on any device connected to it. This can be a smartphone, tablet, or computer. RFID ELLIPSIS works with RFID tags* that can be used to tag your products or formulation ingredients in the database. They can also be used to identify a user. Live Note – Note Down Your Conclusions It’s the first time you can add a voice memo to a measurement series or procedure report. If you prefer to write it down, ELLIPSIS allows you to add a text note. Handy Library This is where a series of recent measurements or a report ready for digital signature, according to 21 CFR Part 11, can be found. Widgets Prepared to display what you need most at any given moment. 21 CFR Part 11 Do you work in the pharmaceutical industry? Do you need a digital signature? We are offering the moisture analyzer which as a standalone fully meets the requirements of 21 CFR Part 11/ EU GMP Annex 11. Full data security Electronic signatures Validations Electronic records Audit trails Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13.56 MHz

HX7 H scale’s multi functions Many functions, many interfaces and great robustness (IP66/ IP68 (more)) mean many possibilities for you to use this advanced scale. Tomorrow you can apply it to a different process than today – that’s the multifunctionality. That’s the saving! Use the potential Barcode scanners, receipt printers, label printers, external displays, control buttons, light signalling towers and other controlling/ signalling devices – thanks to multipurpose software, HX7 scale can work with all of them. You can easily connect them thanks to the fact that the balance is equipped with interfaces: RS232, RS485, USB, Ethernet, 4 IN/ 4 OUT. Optionally, the balance can be equipped with 12 IN/ 12 OUT and analog output module. You can find all accessories in our regular offer. And if you have questions about compatibility, our experts will help you. Easy and pleasant Simple and convenient operation with a 7-inch color display. Perfectly visible messages additionally supported by bargraph. The top part of the operation panel features a bar graph consisting of 9 red and green diode fields. The bar graph is a graphic visualisation informing the user on a current net weight of a product presented with reference to the scale range or declared min and max thresholds. The bracket allows the terminal to be placed on any flat horizontal surface or screwed to the wall with adjustable angle. The power of steel The use of stainless steel guarantees you a long life for the scale. It is not afraid of contact with moist objects or accidental splashes. The construction of the scale is made of a stainless steel. This guarantees you work for many years. Not just weighing But also parts counting, dosing, percent weighing and formulations. The power of HX7’s working mods. Do you need ALIBI? There you have it. ALIBI memory is like a black box of a scale. It records all measurements taken on the device. The ALIBI memory cannot be modified or erased. Referring to stored weighings you can generate weighing reports, formulation reports and reports on performed control processes. Single weighing is stored in the ALIBI memory as long as it is specified by a Weighing Storage Period (days) parameter.

Boekel Scientific 1344 Desiccator, Large w/SS ShelvesThe Boekel Scientific 1344 Desiccator isperfect (more) for drying and storing moisture sensitive laboratory samples.Fabricated from stainless steel and glass. Built for performance anddurability. Superior seal integrity Rigid door full length door hinges One piece neoprene door gasket Shelves are adjustable in half-inch increments Two different sizes to select from 2 year warranty Applications Storing reagents, IR cells or soil samples. Drying biological specimens Storage sludge samples Temperature stabilization prior to weighing Storage of raw materials Storage of API Testing Wastewater total suspended solids Used for crucibles or dishes Food manufacturing and testing INCLUDED: The Boekel Scientific 1344 Desiccator, Large w/SS Shelves includes: - Two Stainless Steel Shelves - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Accessory designed for viscosity measurements of non-flowing substances. In these materials the vis (more)co- sity cannot be measured by standard methods and spindles due to cavitation effect around the spindle. We recommend using the HELDAL unit and T-bar spindles for comparative measurements on non- flowing substances. A Fungilab viscometer is mounted on the Heldal unit, and it restricts measuring head to smoothly run up and down within pre-established limits, allowing cons- tant contact between T-bar spindle and test sample thanks to the helical line described.